• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.2
• /
• pp.45-49
• /
• 2006

Electrochemical hydrogenation/dehydrogenation properties were studied for a single particle of a Mm-based(Mm : minh metal) hydrogen storage alloy($MmNi_{3.55}Co_{0.75}Mn_{0.4}Al_{0.3}$) for fuel cell and Ni-MH batteries. A carbon fiber microelectrode was manipulated to make electrical contact with an alloy particle, and the potential-step experiment was carried out to determine the apparent chemical diffusion coefficient of hydrogen atom($D_{app}$) in the alloy. Since the alloy particle we used here was a dense, conductive sphere, the spherical diffusion model was employed for data analysis. $D_{app}$ was found to vary the order between $10^{-9}\;and\;10^{-10}[cm^2/s]$ over the course of hydrogenation and dehydrogenation process. Compared with the conventional composite film electrodes, the single particle measurements using the microelectrode gave more detailed, true information about the hydrogen storage alloy.

• Journal of the Korean Society of Safety
• /
• v.5 no.2
• /
• pp.32-39
• /
• 1990

The ${\gamma}$-Fe$_2$O$_3$ compounds were oxidized in the furance after gas detecting sensor made molding as the Fe$_3$O$_4$ the synthesized Fe$_3$O$_4$, by ferrous sulfate and sodium hydroxide. Their sensities on carbon monoxide, ethyl alcohol and L. P. G. were measured at various temperatures, respectively. And then their electrical resistivities, thermal properties (D.T.A. ＆ T.G.A.), were examined about their having an effet on the gas-sensing in company with the effect of pure ${\gamma}$-Fe$_2$O$_3$ and the detecting sensor ${\gamma}$-Fe$_2$O$_3$, which reacts with $K_2$CO$_3$ in the hydrothermal coundition, and the electrical conductive mechanism was reflected simultaneously. It was observed that the electrical conductivities and response ratios showed highest value at the endothermic temperature part, 300~35$0^{\circ}C$ of D.T.A.―curve. Consequently, the response ratios and response times of the hydrothermal detecting sensor were higher than that of pure detecting sensor, the specific surface areas were the highest at the endothermic range of D.T.A.-curve. These response ratios of detecting sensor for $K_2$CO$_3$, process at hydrothermal condition on carbon monoxide appeared higher than that on ethyl alcohol and in case of L.P.G. last.

• Composites Research
• /
• v.26 no.5
• /
• pp.315-321
• /
• 2013

In this work, pitch-carbonized glass fibers were prepared for reinforcement of composites. The influence of acid functionalization of the fibers on the morphological, mechanical, and thermal properties of fiber-reinforced epoxy matrix composites was investigated. The acid functionalization of the fibers led to 10 and 150% increases in the mechanical and thermal properties, respectively, as compared to carbon fiber-reinforced composites. This can be attributed to the superior orientation of fiber structures and good interfacial interactions between fillers and epoxy matrix, resulting in enhanced degree of dispersion and formation of thermally conductive paths in the functionalized composites.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.396-396
• /
• 2008

투명 전도성 탄소나노튜브(carbon nanotube, CNT) 필름을 터치스크린이나 디스플레이 소자 등의 전극에 응용할 목적으로, CNT 필름의 전기저항 및 광 투과도를 향상시키기 위한 연구가 활발히 진행되고 있다. 본 연구에서는 단일벽 CNT (single-walled CNT)를 여러 가지 계면활성제로 분산시킨 수용액으로부터 제조한 CNT 필름을 산 처리하여 저항 및 투과도의 변화를 관찰하였다. 우선 계면활성제로 분산시킨 CNT 수용액을 알루미나 재질의 필터에서 정량적으로 진공 필터링하여 CNT 필름을 제조하였다. 알루미나 필터를 sodium hydroxide (NaOH) 수용액으로 용해시켜 제거함으로써 얻은 CNT 필름을 유리기판 위에 부착시킨 후 광 투과도와 먼 저항 (sheet resistance)을 측정하였다. CNT 필름을 질산 ($HNO_3$) 용액에 처리하였을 때 투과도는 1~5 % 향상되었으며, 면 저항은 계면활성제로 분산시킨 CNT 필름 대부분에서 감소하였다. 이는 CNT 표면에 코팅되어 있던 계면활성제들이 산에 의해 제거되었기 때문일 것으로 추측된다. 특히 sodium dodecylbenzene sulfonate (NaDDBS)로 제조한 CNT 필름의 경우, 질산을 처리 전에는 투과도 83%, 면 저항 450 $\Omega$/sq.의 특성을 보였으나, 처리 후에는 각각 86 %, 350 $\Omega$/sq.로 향상되었다. Polyvinyl pyrrolidone (PVP)과 cetyltrimethylammonium bromide (CTAB)를 사용하여 제조한 CNT 필름의 면 저항이 가장 뚜렷한 감소를 보였다. 제조된 필름과 삼 처리된 필름 특성을 Raman spectroscopy, scanning electron microscopy, UV-Vis spectroscopy 등을 이용하여 분석하였고, 4-point probe로 면 저항을 측정하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.5
• /
• pp.517-521
• /
• 2012

Carbon nanotubes (CNTs) have been regarded as a promising material for the fabrication of flexible conductors such as transparent electrodes, flexible heaters, and transparent speakers. In this study, a multiwalled carbon nanotube (MWCNT) film was deposited on a polyethylene terephthalate (PET) substrate using a spraying technique. MWCNTs were dispersed in water using sodium dodecyl sulfate (SDS). To evaluate the effect of the weight ratio between SDS and MWCNTs on the electromechanical properties of the film, direct tensile tests and optical strain measurement were conducted. It was found that the CNT film hardly affected the mechanical behavior of CNT/PET composite films, while the electrical behavior of the CNT film was strongly affected by the SDS concentration in the CNT film. The electrical resistance of CNT/PET films gradually increased with the strain applied to the PET substrate, even up to a large strain that ruptured the substrate.

• Composites Research
• /
• v.16 no.2
• /
• pp.68-73
• /
• 2003

Interfacial properties and electrical sensing fer fiber fracture in carbon and SiC fibers/epoxy composites were investigated by the electrical resistance measurement and fragmentation test. As fiber-embedded angle increased, the interfacial shear strength (IFSS) of two-type fiber composites decreased, and the elapsed time takes long until the infinity in electrical resistivity. The initial slope of electrical resistivity increased rapidly to the infinity at higher angle, whereas electrical resistivity increased gradually at small angle. Furthermore, both fiber composites with small embedded angle showed a fully-developed stress whitening pattern, whereas both composites with higher embedded angle exhibited a less developed stress whitening pattern. As embedded angle decreased, the gap between the fragments increased and the debonded length was wider for both fiber composites. Electro-micromechanical technique could be a feasible nondestructive evaluation to measure interfacial sensing properties depending on the fiber-embedded angle in conductive fiber reinforced composites.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.2
• /
• pp.157-164
• /
• 2012

The design strategy of the multi-functional structure is that the electrical components and the circuits are directly put on their supporting structural panel in which the radiation shields and the thermal control functions are integrated. Applying the multi-functional structure reduces the total mass and size of the space system and makes it possible to lower launch cost. In present study the performance of thermal radiation for six types of multi-functional structure are investigated by the numerical method. The effect of the rib configuration on heat transfer for the multi-functional-structure is not important alone but is meaningful considering with the structural stiffness, difficulty of manufacturing and mass increase. In heat spreading point of view, the thickness of the outer conductive layer is important rather than the rib configuration and the trade-off study with the mass and thickness is required for optimum design.

• Korean Journal of Materials Research
• /
• v.20 no.2
• /
• pp.51-54
• /
• 2010

Transparent conductive films of single wall carbon nanotube (SWCNT) were prepared by spray coating method. The effect of acid treatment on the SWCNT films was investigated. The field emission scanning electron microscope (FESEM) shows that acid treatment can remove dispersing agent. The electrical and optical properties of acid-treated films were enhanced compared with those of as deposited SWCNT films. Nitric acid ($HNO_3$), sulfuric acid ($H_2SO_4$), nitric acid:sulfuric acid (3:1) were used for post treatment. Although all solutions reduced sheet resistance of CNT films, nitric acid can improve electrical characteristics efficiently. During acid treatment, transmittance was increased continuously with time. But the sheet resistance was decreased for the first 20 minutes and then increased again. Post-treated SWCNT films were transparent (85%) in the visible range with sheet resistance of about $162{\Omega}/sq$. In this paper we discuss simple fabrication, which is suitable for different types of large-scale substrates and simple processes to improve properties of SWCNT films.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.156-156
• /
• 2016

The effect of nitrogen doping on the mechanical and tribological performance of single-layer tetrahedral amorphous carbon (ta-C:N) coatings of up to $1{\mu}m$ in thickness was investigated using a custom-made filtered cathode vacuum arc (FCVA). The results obtained revealed that the hardness of the coatings decreased from $65{\pm}4.8GPa$ to $25{\pm}2.4GPa$ with increasing nitrogen gas ratio, which indicates that nitrogen doping occurs through substitution in the $sp^2$ phase. Subsequent AES analysis showed that the N/C ratio in the ta-C:N thick-film coatings ranged from 0.03 to 0.29 and increased with the nitrogen flow rate. Variation in the G-peak positions and I(D)/I(G) ratio exhibit a similar trend. It is concluded from these results that micron-thick ta-C:N films have the potential to be used in a wide range of functional coating applications in electronics. To achieve highly conductive and wear-resistant coatings in system components, the friction and wear performances of the coating were investigated. The tribological behavior of the coating was investigated by sliding an SUJ2 ball over the coating in a ball-on-disk tribo-meter. The experimental results revealed that doping using a high nitrogen gas flow rate improved the wear resistance of the coating, while a low flow rate of 0-10 sccm increased the coefficient of friction (CoF) and wear rate through the generation of hematite (${\alpha}-Fe_2O_3$) phases by tribo-chemical reaction. However, the CoF and wear rate dramatically decreased when the nitrogen flow rate was increased to 30-40 sccm, due to the nitrogen inducing phase transformation that produced a graphite-like structure in the coating. The widths of the wear track and wear scar were also observed to decrease with increasing nitrogen flow rate. Moreover, the G-peaks of the wear scar around the SUJ2 ball on the worn surface increased with increasing nitrogen doping.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.152-152
• /
• 2008

탄소나노튜브(carbon nanotube) 필름은 낮은 전기저항, 높은 투명도, 우수한 기계적 강도 및 유연성, 열적 안정성 등의 뛰어난 특성을 가지고 있다. 본 연구에서는 다양한 계면활성제로 분산시킨 수용액으로부터 제조된 단일벽 탄소나노튜브(single-walled CNT) 필름의 면저항(sheet resistance) 특성을 비교하였다. 먼저 나노튜브의 분산을 위해 널리 사용되는 계면활성제인 sodium dodecyl sulfate(SDS)를 기준으로 탄소나노튜브의 양, 원심분리 시간, 초음파 세기 및 시간 등의 최적 공정조건을 정한 후 각 계면활성제에 대해 분산을 위한 최적 첨가량을 알아내어 계면활성제 별로 탄소나노튜브 수용액을 제조하였다. 다양한 계면활성제로 분산된 단일벽 탄소나노튜브 수용액을 알루미나 재질의 필터에 정량적으로 vacuum-filtration하여 필름을 만들었다. 이 필름들의 면저항을 측정함으로써 계면 활성제에 따른 전기적 특성의 차이를 관찰하였다. 본 연구에서 사용한 여러 가지 계면활성제 중 sodium dodecylbenze nesulfonate (NaDDBS)를 사용하여 만든 필름이 가장 낮은 면저항을 나타내었으며, 이는 NaDDBS가 단일벽 탄소나노 튜브 다발들을 개개의 튜브로 잘 분산시키기 때문인 것으로 생각된다.