• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.6
• /
• pp.50-59
• /
• 2021

Currently, the response correction factor is calculated by comparing the response measured by the load test on a bridge with the response analyzed in the initial analytical model. Then the load rating and the load carrying capacity are evaluated. However, the response correction factor gives a value that fluctuates depending on the measurement location and load condition. In particular, when the initial analytical model is not suitable for representing the behavior of a bridge, the range of variation is large and the analysis response by the calibrated model may give a result that is different from the measured response. In this study, a pseudo-static load test was applied to obtain static response with dynamic components removed under various load conditions of a vehicle moving at a low speed. Static response was measured on two similar PSC-I girder bridges, and the response correction factors for displacement and strain were calculated for each of the two bridges. When the initial analysis model was not properly set up, it is verified that the response of the analytical model corrected by the average response correction factor does not fall within the margin of error with the measured response.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.3D
• /
• pp.385-391
• /
• 2006

It is very important to make a decision for locating public facility site in a objectively way people in general agree with. This is because public facility affects not only daily life of people in there but also a regional development. This paper sets up a site selection model which utilize an accessibility theory and GIS spatial analysis techniques. This model has been applied to all the twelve alternatives of Chungnam Provincial Office (CPO) sites which are well known to the public. On the criterion of average access time from all the other areas in Chungnam Province, CH alternative is found to be the best one followed by CH/AS, AS alternatives. On the basis of total people-travel time CH/AS alternative turns out to be the best one followed by CH, AS alternatives. In conclusion top three best locations for CPO are CH and AS area where transportation facility are in good condition and population density is highest in Chungnam Province. This fact implies that a transportation accessibility and population density are the primary key in determining the location of public facility.

• Journal of KIISE:Databases
• /
• v.30 no.3
• /
• pp.296-309
• /
• 2003

One of commercial applications of mobile computing is ATIS(Advanced Traveler Information Systems) in ITS(Intelligent Transport Systems). In ATIS, a primary mobile computing task is to compute the shortest path from the current location to the destination. In this paper, we have studied the shortest path re-computation problem that arises in the DRGS(Dynamic Route Guidance System) in ATIS where the cost of topological digital road map is frequently updated as traffic condition changes dynamically. Previously suggested methods either re-compute the shortest path from scratch or re-compute the shortest path just between the two end nodes of the edge where the cost change occurs. However, these methods we trivial in that they do not intelligently utilize the previously computed shortest path information. In this paper, we propose an efficient approximate shortest path re-computation method based on the dynamic window scheme. The proposed method re-computes an approximate shortest path very quickly by utilizing the previously computed shortest path information. We first show the theoretical analysis of our methods and then present an in-depth experimental performance analysis by implementing it on grid graphs as well as a real digital road map.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.3
• /
• pp.303-310
• /
• 2021

Cracks in bridges are important factors that indicate the condition of bridges and should be monitored periodically. However, a visual inspection conducted by a human expert has problems in cost, time, and reliability. Therefore, in recent years, researches to apply a deep learning model are started to be conducted. Deep learning requires sufficient data on the situations to be predicted, but bridge crack data is relatively difficult to obtain. In particular, it is difficult to collect a large amount of crack data in a specific situation because the shape of bridge cracks may vary depending on the bridge's design, location, and construction method. This study developed a crack detection model that generates and trains insufficient crack data through a Generative Adversarial Network. GAN successfully generated data statistically similar to the given crack data, and accordingly, crack detection was possible with about 3% higher accuracy when using the generated image than when the generated image was not used. This approach is expected to effectively improve the performance of the detection model as it is applied when crack detection on bridges is required, though there is not enough data, also when there is relatively little or much data f or one class.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.17
• /
• pp.1-44
• /
• 1974

These studies were made at Suwon in 1972 and at Suwon, Iri, and Kwangju in 1973 to investigate grain filling process and variation of grain quality of NB 68513 and Caprock as hard red winter wheat, Suke ＃169 as soft red winter wheat variety and Yungkwang as semi-hard winter variety, grown under-three different fertilizer levels and seeding dates. Other experiments were conducted to find the effects of temperature, humidity and light intensity on the grain filling process and grain quality of Yungkwang and NB 68513 wheat varieties. These, experiments were conducted at Suwon in 1973 and 1974. 1. Grain filling process of wheat cultivars: 1) The frequency distribution of a grain weight shows that wider distribution of grain weight was associated with large grain groups rather than small grain group. In the large grain groups, the frequency was mostly concentrated near mean value, while the frequency was dispersed over the values in the small grain group. 2) The grain weight was more affected by the grain thickness and width than by grain length. 3) The grain weight during the ripening period was rapidly increased from 14 days after flowering to 35 days in Yungkwang and from 14 days after flowering to 28 days in NB 68513. The large grain group, Yungkwang was rather slowly increased and took a longer period in increase of endosperm ratio of grain than the small grain group, NB 68513. 4) In general, the 1, 000 grain weight was reduced under high temperature, low humidity, while it was increased under low temperature and high humidity condition, and under high temperature and humidity condition. The effect of shading on grain weight was greater in high temperature than in low temperature condition and no definite tendency was found in high humidity condition. 5) The effects of temperature, humidity and shading on 1, 000 grain weight were greater in large-grain group, Yungkwang than in small grain group, NB 68513. Highly significant positive correlation was found between 1, 000 grain weight and days to ripening. 6) The 1, 000 grain weight and test weight were increased more or less as the fertilizer levels applied were increased. However, the rate of increasing 1, 000 grain weight was low when fertilizer levels were increased from standard to double. The 1, 000 grain weight was high when planted early. Such tendency was greater in Suwon than in Kwangju or Iri area. 2. Milling quality: 7) The milling rate in a same group of varieties was higher under the condition of low temperature, high humidity and early maturing culture which were responsible for increasing 1, 000 grain weight. No definite relations were found along with locations. 8) In the varieties tested, the higher milling rate was found in large grain variety, Yungkwang, and the lowest milling rate was obtained from Suke ＃ 169, the small grain variety. But the small grained hard wheat variety such as Caprock and NB 68513 showed higher milling rate compared with the soft wheat variety, Suke ＃ 169. 9) There were no great differences of ash content due to location, fertilizer level and seeding date while remarkable differences due to variety were found. The ash content was high in the hard wheat varieties such as NB 68513, Caprock and low in soft wheat varieties such as Yungkwang and Suke ＃ 169. 3. Protein content: 10) The protein content was increased under the condition of high temperature, low humidity and shading, which were responsible for reduction of 1, 000 grain weight. The varietal differences of protein content due to high temperature, low humidity and shading conditions were greater in Yungkwang than in NB 68513. 11) The high content of protein in grain within one to two weeks after flowering might be due to the high ratio of pericarp and embryo to endosperm. As grains ripen, the effects of embryo and pericarp on protein content were decreased, reducing protein content. However, the protein content was getting increased from three or four weeks after flowering, and maximized at seven weeks after flowering. The protein content of grain at three to four weeks after flowering increased as the increase of 1, 000 grain weight. But the protein content of matured grain appeared to be affected by daily temperature on calender rather than by duration of ripening period. 12) Highly significant positive correlation value was found between the grain protein content and flour protein content. 13) The protein content was increased under the high level of fertilizers and late seeding. The local differences of protein content were greater in Suwon than in Kwangju and Iri. 14) Protein content in the varieties tested were high in Yungkwang, NB 68513 and Caprock, and low in Suke ＃ 169. However, variation in protein content due to the cultural methods was low in Suke ＃ 169. 15) Protein yield per unit area was increased in accordance with increase of fertilizer levels and early maturing culture. However, nitrogen fertilizer was utilized rather effectively in early maturing culture and Yungkwang was the highest in protein yield per unit area. 4. Physio-chemical properties of wheat flour: 16) Sedimentation value was higher under the conditions of high temperature, low humidity and high levels of fertilizers than under the conditions of low temperature, high moisture and low levels of fertilizers. Such differences of sedimentation values were more apparent in NB 68513 and Caprock than Yungkwang and Suke ＃ 169. The local difference of sedimentation value was greater in Suwon than in Kwangju and Iri. Even though the sedimentation value was highly correlated with protein content of grain, the high humidity was considered one of the factors affecting sedimentation value. 17) Changes of Pelshenke values due to the differences of cultural practices and locations were generally coincident with sedimentation values. 18) The mixing time required for mixogram was four to six minutes in NB 68513, five to seven minutes in Cap rock. The great variation of mixing time for Yungkwang and Suke ＃ 169 due to location and planting conditions was found. The mixing height and area were high in hard wheat than in soft wheat. Variation of protein content due to cultural methods were inconsistent. However, the pattern of mixogram were very much same regardless the treatments applied. With this regard, it could be concluded that the mixogram is a kind of method expressing the specific character of the variety. 19) Even though the milling property of NB 68513 and Caprock was deteriorated under either high temperature and low humidity of high fertilizer levels and late seeding conditions, baking quality was better due to improved physio-chemical properties of flour. In contrast, early maturing culture deteriorated physio-chemical properties, milling property of grain and grain protein yield per unit area was increased. However, it might be concluded that the hard wheat production of NB 68513 and Caprock for baking purpose could be done better in Suwon than in Iri or Kwangju area. 5. Interrelationships between the physio-chemical characters of wheat flour: 20) Physio-chemical properties of flour didn't have direct relationship with milling rate and ash content. Low grain weight produced high protein content and better physio-chemical flour properties. 21) In hard wheat varieties like NB 68513 and Caprock, protein content was significantly correlated with sedimentation value, Pelshenke value and mixing height. However, gluten strength and baking quality were improved by the increased protein content. In Yungkwang and Suk ＃ 169, protein content was correlated with sedimentation value, but no correlations were found with Pelshenke value and mixing height. Consequently, increase of protein content didn't improve the gluten strength in soft wheat. 22) The highly significant relationships between protein content and gluten strength and sedimentation . value, and between Pelshenke value, mixogram and gluten strength indicated that the determination of mixogram and Pelshenke value are useful for de terming soft and hard type of varieties. Determination of sedimentation value is considered useful method for quality evaluation of wheat grain under different cultural practices.

• Korean Journal of Health Education and Promotion
• /
• v.18 no.3
• /
• pp.133-162
• /
• 2001

Unexpected accidents in school has been gradually increased every year, and student's mistaken was the first reason of the accident. To preventing the students from Unexpected accidents in school, safety education is more important than having strong facilities to have much more strong protecting forces for the accidents. Therefore, systematic education of safety is needed most of all, and especially, strengthening safety education in school is needed. Hereby, this study is aimed at investigating and analysing the actual condition and demand of safety education. It also conducted a survey with the target of 1,255 students in the second grade of high school in Seoul from April 20 to May 19, and the result of this study is as follows. 1. In the general features of the subject of the survey, boy students and girl students occupied 50.8％ and 49.2％ each, and boys' high school (34.3％), girls' high school(32.2％) and co-ed(33.5％) participated in balance. In the location, north from Han river occupied 54.6％, south were 45.2％. 2. According to the status of experiencing an accident, boys were more experienced then girls(p〈0.05). From the section, home accident(56.8％) occupied most followed by school accident, traffic accident, sports accident and poisoning. The accident happening most often in detailed category is sports accident such as basket ball, foot ball and dodge ball. The actual condition of the subject's using a school health facility shows that boys students use it more often than girl students(p〈0.01) 3. In attitude toward safety, the subject showed lower interest in safety issues than other social issues. But attitude in seriality of safety problems were high. Also, they responded ‘individual citizen’(63.1％) as the one who should make efforts for safety. Regarding knowledge of preventing safety accidents in attitude toward individual safety, 42.2％ answered ‘they know a little’ and 32.6％ of respondents say ‘they do not know’. To a question of the degree of the subject's following safety rules, 36.4％ were answered ‘keeping’ and the group using a school health facility shows more ‘keeping’ the others(p〈0.05). 4. To a question of asking if they have experienced safety education, 51.2％ answered ‘yes’. Teachers who mainly take care of safety education are answered as training teacher(48.7％). As for education time, training class(51.3％) is said to have safety education most followed by health-related event and PE(Physical Education). Frequency of education shows once or twice a session (62.8％) most often, but in case of co-ed school, 5-7times a session or more(20.1％) are being practiced. Looking at education time, 1-2 hour(s)(22.1％) or for a short time(22.1％) during class are being practiced. As an education method, instruction(43.8％) and video education(32.5％) are being practiced, and when it comes to education evaluation method, ‘not practiced’(70.0％) answered. To the question if they are satisfied with school safety education, they answered more ‘no(43.1％)’ than ‘yes(6.7％)’, and the reason is that safety education class is just for formality's sake, and the fact they already know is being repeated. The contents of safety education is composed of school safety, home safety, and first aid. 5. It is turned out that 56.5％ of the total boy students and 61.1％ of the total girl students recognize the necessity of safety education. To the question if safety education is needed in an elementary and middle education course, 46.4％ of the subject answer answered' it's necessary'. The most reason for their answers are ‘safety education is directly related to life’. 6. Regarding the requested time of safety education is ‘one hour a week’ by 55.9％. For safety education, safety education teachers(38.7％) are answered to be the most proper. As a request for safety education, video education is answered to be the most appropriate(30.6％), followed by practical skills, lecture and discussion(p〈0.05). Demand of educational evaluation, practical skills, interview and observation are answered to be needed. To the question if they want to participate in the way of demanded safety education, 41.9％ of respondents answer ‘have a mind to participate in’ (41.9％). To benefits followed by completing safety education, 72.0％ of respondents answer ‘agree’, and 24.7％ ‘do not agree’, which means lout 4 disagrees with completing safety education. 7. Looking at demand of safety education according to the features of the subject, ‘our position for the person who has handicapped’ was answer to the most.

• Progress in Medical Physics
• /
• v.25 no.2
• /
• pp.100-109
• /
• 2014

In stereotactic body radiotherapy (SBRT), the accurate location of treatment sites should be guaranteed from the respiratory motions of patients. Lots of studies on this topic have been conducted. In this letter, a new verification method simulating the real respiratory motion of heterogenous treatment regions was proposed to investigate the accuracy of lung SBRT for Volumetric Modulated Arc Therapy. Based on the CT images of lung cancer patients, lung phantoms were fabricated to equip in $QUASAR^{TM}$ respiratory moving phantom using 3D printer. The phantom was bisected in order to measure 2D dose distributions by the insertion of EBT3 film. To ensure the dose calculation accuracy in heterogeneous condition, The homogeneous plastic phantom were also utilized. Two dose algorithms; Analytical Anisotropic Algorithm (AAA) and AcurosXB (AXB) were applied in plan dose calculation processes. In order to evaluate the accuracy of treatments under respiratory motion, we analyzed the gamma index between the plan dose and film dose measured under various moving conditions; static and moving target with or without gating. The CT number of GTV region was 78 HU for real patient and 92 HU for the homemade lung phantom. The gamma pass rates with 3%/3 mm criteria between the plan dose calculated by AAA algorithm and the film doses measured in heterogeneous lung phantom under gated and no gated beam delivery with respiratory motion were 88% and 78%. In static case, 95% of gamma pass rate was presented. In the all cases of homogeneous phantom, the gamma pass rates were more than 99%. Applied AcurosXB algorithm, for heterogeneous phantom, more than 98% and for homogeneous phantom, more than 99% of gamma pass rates were achieved. Since the respiratory amplitude was relatively small and the breath pattern had the longer exhale phase than inhale, the gamma pass rates in 3%/3 mm criteria didn't make any significant difference for various motion conditions. In this study, the new phantom model of 4D dose distribution verification using patient-specific lung phantoms moving in real breathing patterns was successfully implemented. It was also evaluated that the model provides the capability to verify dose distributions delivered in the more realistic condition and also the accuracy of dose calculation.

• Land and Housing Review
• /
• v.4 no.1
• /
• pp.77-87
• /
• 2013

About 1,800 villages have released from Greenbelt since Greenbelt-reform-policy for readjustment of the area was promoted after 1997. Even though the government intended to attract planned development & improvement of these lifted villages through District Unit Plan and designating the lifted area as low-rise and low-density zoning considering the characteristics of the Greenbelt region, there are still many problems to be solved: a lack of funds, insufficient capability for self-improvement and unexecuted SOCs in long-term etc. It seems that these problems are caused by focusing on the lifting areas itself instead of researching deeply the condition and characteristics of the villages and searching proper direction/plans of improvement before lifting Greenbelt In addition, the existing plan of village improvement and management was not considering physical and spacial characteristics of the areas, social and economic situation of residents and relationship between the villages and surrounding cities, though these conditions are different among each villages, and the related regulations are applied uniformly across all the villages and those have been causing many civil appeals and environmental problems. In these respects, this study aims to consider the problems of the lifted villages using the existing researches on them and to make typology by characteristics-data of the villages and to establish improvement strategies of each types. In this study, the villages were classified into 5 types as a result of cluster analysis on 424 villages among all 1,800 through variables of locational potentiality : location, accessibility, size and form of village, condition of regulations etc. According to function of the villages, they were divided into 4 types: urban-type, rural-type, industrial-type and neighborhood-centered-type. This study also drew 4 improvement-strategy-types by combination of locational potentiality and village-function : type of improving life-environment, type of improving production-infra, type of inducing-planned-improvement and type of constructing center-of living-circle. Finally, this study suggested the directions of the each 4 types to desirable improvement and management which could be used to make and complement plans for village improvement.

• Journal of dental hygiene science
• /
• v.4 no.3
• /
• pp.117-126
• /
• 2004

For a month of September, 2004, a questionnaire regarding dental hygiene was distributed to 165 workers of Ulsan area. A total of 125 questionnaire were analyzed: 102 collected of the distributed 165 pieces, and 23 questionnaires reported by patients of a dental clinic in Dong-gu, Woolsan. The result is as follows; (1) Labor workers of Ulsan have thought that they are in good dental health, 44.1% of respondents, following by those who they believe they are in moderate health and those who they think are in poor condition. 89.0% of total workers have experienced dental treatment. (2) Regarding the location of dental treatment, 85.0% of respondents have pointed out dental hospitals and clinics, while 3.9% have indicated that they had treatment from unlicensed dentists. Specifically, workers in their 40s over have ever experienced dental treatment by unlicensed dentists. Those who think they are in poor dental condition have tended to have more dental treatment by unlicensed dentists. (3) Regarding the reason that they put off the treatment, 59.1% of respondents have indicated that they have no time to have the treatment, following by economic burden and the lack of confidence in dentists. When they have tooth aches or the gum ache, 60% of respondents have suggested that they endure the ache or take a medicine to alleviate the pain, showing a lower understanding of early dental treatment. (4) Regarding the reason why they are unwilling to go to dentists, respondents have revealed the anxiety against pain, 50.4%, following by the difficulty of scheduling and unsatisfied services. (5) 47.2% of respondents have brushed their teeth 3 times everyday, following by those who have done it 2 times a day and those one a day. Regarding how to brush the teeth, most of respondents have brushed their teeth in the upper, lower, and the both side, 61.4%. The younger respondents and those who think they are in good dental health have tended to brush their teeth up and down. (6) Regarding the cause of the gum disease, 67.7% of respondents have thought that it is caused by poor dental hygiene, following by natural occurrence due to age, hereditary nature, and physical predisposition. (7) 67.7% of respondents have experienced dental scaling, while 32.3% of them have had no experience in it. 53.5% of workers have thought that scaling may not be recommended since they have the teeth scaled periodically once they had dental scaling, a higher rate than 46.5% who think scaling is good for the gum health.

• Journal of Internet Computing and Services
• /
• v.16 no.1
• /
• pp.57-65
• /
• 2015

As information technology fusion is accelerated, the researches to improve the quality and productivity of crops inside a plant factory actively progress. Advanced growth environment management technology that can provide thermal environment and air flow suited to the growth of crops and considering the characteristics inside a facility is necessary to maximize productivity inside a plant factory. Currently running plant factories are designed to rely on experience or personal judgment; hence, design and operation technology specific to plant factories are not established, inherently producing problems such as uneven crop production due to the deviation of temperature and air flow and additional increases in energy consumption after prolonged cultivation. The optimization process has to be set up in advance for the arrangement of air flow devices and operation technology using computational fluid dynamics (CFD) during the design stage of a facility for plant factories to resolve the problems. In this study, the optimum arrangement and air flow of air circulation fans were investigated to save energy while minimizing temperature deviation at each point inside a plant factory using CFD. The condition for simulation was categorized into a total of 12 types according to installation location, quantity, and air flow changes in air circulation fans. Also, the variables of boundary conditions for simulation were set in the same level. The analysis results for each case showed that an average temperature of 296.33K matching with a set temperature and average air flow velocity of 0.51m/s suiting plant growth were well-maintained under Case 4 condition wherein two sets of air circulation fans were installed at the upper part of plant cultivation beds. Further, control of air circulation fan set under Case D yielded the most excellent results from Case D-3 conditions wherein air velocity at the outlet was adjusted to 2.9m/s.