• Journal of Ocean Engineering and Technology
• /
• v.23 no.1
• /
• pp.152-157
• /
• 2009

In designing and manufacturing a submarine, an expensive real mock up is usually built as a reference because of the spatial constraints of a submarine. This paper presents an integrated and automated design process for a submarine that uses a digital mock up. Various equipment libraries are built for feature based design. Using the developed digital mock up, this paper shows various ways to verify the design, including a space analysis to check for any interference between pieces of equipment and the hull and an ergonomic analysis using lifelike dummies to examine the work space and operability. As a part of the integrated design system, a design automation system was also developed to generate surface point data for the outer hull, pressure hull, casing, and sail. The whole process was applied to the design of a submarine for verification.

• International Journal of Aeronautical and Space Sciences
• /
• v.15 no.3
• /
• pp.309-319
• /
• 2014

This paper mainly focuses on the conceptual design and stealth performance of the three-surface military aircraft. A three-dimensional (3-D) digital mock-up of the three-surface strike fighter with stealth feature was designed and the schemes of carrying missiles were analyzed in CATIA. Based on physical optics principle and the Method of Equivalent Currents (MEC), a numerical simulation of the RCS feature of the aircraft was carried out with RCSPlus which is a software designed by Beihang University. The paper contributes to the RCS feature analysis of the whole plane and different parts on X-band, S-band and UHF-band and a comparison of RCS feature to Su-37 and T-50 military aircraft is drawn. On X-band, the pitch angle of the incident wave was $0^{\circ}$, and the result shows: (1) Compared with Su-37 aircraft, the forward scattering RCS of the three-surface strike aircraft was reduced to 14.9%, the side scattering RCS to 9.6% and the back scattering RCS to 40.2%. (2) Compared with T-50 aircraft, the forward scattering RCS was reduced to 38.61%, and the side scattering RCS to 67.26%. This paper should be useful for researchers in conceptual design and stealth technology of the military aircraft.

• Journal of the Korean Society of Costume
• /
• v.57 no.7
• /
• pp.70-83
• /
• 2007

Contemporary fashion design has been made a new attempt to extend restricted expressions through fusion with other genres in art. The recognition of fashion has recently been changed not only product but as a piece of work in specific value, concept and meaning created by fashion designer. It is observed that the contemporary fashion design has a notion to persue formative intentions and manners of Conceptual Art in Post-modern era. This study is to define this region of fashion design represented in cultural phenomena as 'Conceptual Fashion', also analyze the formative feature of this from a point of view in Conceptual art. The results which are analyzed according to outward techniques and forms, meanings and elements immanent in aesthetic contemplation of conceptual fashion lead to four distinctive things in such as anti-form, intervention and appropriation, metaphor and detour, process and series. The intrinsic values in conceptual fashion through aesthetic contemplation are indicated the four significant values in the following: the pluralistic interpretation, the parody and amusement, the pursuit of essence and truth and the participation and interaction. Conceptual fashion design is appeared complex not doing separate through classified formative features previously. And It has been evolved as a indeterminate concept which is able to variable elucidation by a non-player, as a instrument for communication on fashion culture which is aggrandized. The purpose of this study is to present of theoretical foundation about Conceptual fashion design and also to make proper understanding about interrelationship between contemporary fashion and art.

• International Journal of Aeronautical and Space Sciences
• /
• v.14 no.3
• /
• pp.222-228
• /
• 2013

A jetfighter shape modeling method based on design features is researched, to improve the efficiency of shape modeling in the stage of conceptual aircraft design. The aircraft's general design features and shape parameters, including geometric and position parameters, are described. The coordinate systems of the entire aircraft and its components are defined. As a sample of local shape, a method of inlet intake modeling is introduced. The whole process of the modeling method is proposed. Three examples of different jetfighters are listed, to describe the achievement of basic layout, which includes four main elements. The Fusion of Components can be achieved by regulating the details of the sections of the fuselage. Sample Cases of typical layouts are shown to verify the effectiveness of the proposed method, which provides the basis for further analysis and optimization.

• Nuclear Engineering and Technology
• /
• v.45 no.6
• /
• pp.721-730
• /
• 2013

Within the framework of the ASTRID project, core design studies are being conducted by the CEA with support from AREVA and EDF. The pre-conceptual design studies are being conducted in accordance with the GEN IV reactor objectives, particularly in terms of improving safety. This involves limiting the consequences of 1) a hypothetical control rod withdrawal accident (by minimizing the core reactivity loss during the irradiation cycle), and 2) an hypothetical loss-of-flow accident (by reducing the sodium void worth). Two types of cores are being studied for the ASTRID project. The first is based on a 'large pin/small spacing wire' concept derived from the SFR V2b, while the other is based on an innovative CFV design. A distinctive feature of the CFV core is its negative sodium void worth. In 2011, the evaluation of a preliminary version (v1) of this CFV core for ASTRID underlined its potential capacity to improve the prevention of severe accidents. An improved version of the ASTRID CFV core (v2) was proposed in 2012 to comply with all the control rod withdrawal criteria, while increasing safety margins for all unprotected-loss-of-flow (ULOF) transients and improving the general design. This paper describes the CFV v2 design options and reports on the progress of the studies at the end of pre-conceptual design phase 1 concerning: - Core performance, - Intrinsic behavior during unprotected transients, - Simulation of severe accident scenarios, - Qualification requirements. The paper also specifies the open options for the materials, sub-assemblies, absorbers, and core monitoring that will continue to be studied during the conceptual design phase.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.9
• /
• pp.84-93
• /
• 1996

This paper describes the development of new feature positioning method which embedded into the top-down assembly modeling system supporting conceptual design. In this work, the user provides the geometric constraints representing the position and size of features, then the system calculates their proper solution. The use of geometric constraints which are easy to understand intuitively enables the user to represent his design intents about geometric shapes, and enables the system to propagate the changes automatically when some editing occurs. To find the proper solution of given constraints, the Selective Solving Method in which the redundant or conflict equations are detected and discarded is devised. The validity of feature shapes satisfying the constraints can be maintained by this technique, and under or over constrained user-defined constraints can also be estimated. The problems such as getting the initial guess, controlling the multiple solutions, and dealing with objects of rotational symmetry are also resolved. Through this work, the feature based modeling system can support more general and convenient modeling method, and keeps the model being valid during modifying models.

• Korean Institute of Interior Design Journal
• /
• v.22 no.3
• /
• pp.3-10
• /
• 2013

The purpose of this study is to analyze environmental-friendly design features in landscape architecture. The process of the study first started theoretical research of 'Environmental-friendly' and 'Landscape', then extracted primary conceptual elements that based on ecological background, and analyze 20 cases, from 1990 to now, based on elements that extracted. Summarizing about environment-friendly feature in landscape architecture of Form, Space, Energy Management is as following. First, In the formal aspect, Landscape architecture tend to harmonize with surrounding environment through horizontal, vertical continuity that is realized to transform artificial plate. Second, In the spatial aspect, Landscape architectural space has flexible feature. It is expression through methods blur boundary between outside and inside, lead to change and experience by time, indeterminacy of program. Third, In the energy management aspect, the introduction of effective energy system increase environmental features in space through technical application and environmental-friendly materials.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.7
• /
• pp.1604-1618
• /
• 1995

In the process of mechanical assembly design, assembly modeling systems have been used mainly for the design verification before manufacturing by enabling to check the interference and/ or the dynamic and kinematic performance. However, the conventional assembly modeling systems have a shortcoming that they can not be used in the initial design stage but can be used only after the design is fully completed. In other words conventional assembly modeling systems provide bottom-up modeling which means that the detailed modeling of components must precede the definition of relationships between them. To resolve this problem, an assembly modeling system is proposed to provide a top-down modeling environment in which components and assembly can be modeled simultaneously. To this end, an assembly data structure suitable for top-down assembly modeling has been established. Feature positioning Module(FPM) using geometric constraints has been also developed. The Sekective Solving Method proposed for FPM is based on the priority between the constraint equations and enables the designer's intent expressed by geometric constraints to be maintained throughout the whole modeling process. Finally, the feature based modeling technique using two-level features has been developed. Two-level features include an abstract model and a detailed model in a merged form in non-manifold data frame.

• Korean Journal of Computational Design and Engineering
• /
• v.12 no.4
• /
• pp.283-297
• /
• 2007

Seamless data integration in the CAx chain of the CAD/CAPP/CAM/CNC has been achieved to a high degree, but research concerning the transfer of data from conceptual sketches to a CAD system should be carried out further. This paper presents a method for reconstructing a 3D model from a freehand sketch. Sketch-based modeling research can be classified into gestural modeling methods and reconstructional modeling methods. This research involves the reconstructional modeling method. Here, Mitani's seminal work, designed for box-shaped 3D model using a predefined template, is improved by leveraging a relational template and specialized for automotive design. Matching between edge graphs of the relational template and the sketch is formulated and solved as the assignment problem using the feature vectors of the edges. Including the stroke preprocessing method required to generate an edge graph from a sketch, necessary procedures and relevant techniques for implementing the template-based modeling method are described. Examples from a working implementation are given.

• Advances in Computational Design
• /
• v.5 no.4
• /
• pp.381-396
• /
• 2020

This study aimed to develop an optimal model of transportation for people with disabilities. To achieve this goal, powers of research and design should be involved, including CAD software. This paper investigates both: the concept of optimal model of transportation for people with disabilities (functional, ergonomic, constructive, technological and aesthetic solutions included); and its implementation as a fully-fledged 3D-model designed in SolidWorks environment. The optimal model of transportation is complex and consists of two objects. The first object is for indoors that is a wheelchair, the second one is for street driving that is an individual vehicle. The optimal model of transportation is universal and multifunctional, which have become possible with parametric feature-based approach utilized in SolidWorks.