• 청정기술
• /
• 제25권1호
• /
• pp.63-73
• /
• 2019

연소공정 내에서 질소산화물 배출을 저감하는 선택적 무촉매 환원장치 내부의 화학반응 및 저감효율에 대한 수치해석이 실행되었다. 선택적 무촉매 환원장치에서 저감된 질소산화물은 질소뿐만 아니라 아산화질소로도 전환된다. 아산화질소는 온실가스로써 지구온난화에 영향을 끼치기 때문에 선택적 무촉매 환원장치 내의 질소산화물 제어와 동시에 아산화질소 생성제어가 요구되어진다. 본 연구에서는 선행연구에서 실행된 실험과 온도조건과 가성소다의 첨가량이 동일한 선택적 무촉매 환원장치 내의 전산해석을 실시하고 비교하여 전산해석의 신뢰성을 확인하고, 가성소다 첨가량을 추가적으로 조절하여 질소산화물의 저감 효율과 아산화질소 생성량을 예측하였다. 전산해석은 후단의 측정점을 설정하여 각 물질의 질량분율을 확인하였다. 세부적으로는 측정점에서 유동방향에 수직한 면을 설정하여 온도 조건과 가성소다 첨가량에 따른 각 물질의 평균 질량분율을 비교하였다. 실험값과 전산해석에 의한 모사값은 최대 18.9%의 오차를 보이며 대체적으로 잘 예측됨을 확인하였으며 가성소다 첨가량을 증가시켰을 땐 70% 이상의 제거율의 온도 범위가 넓어지는 것을 확인하였다. 따라서 반응온도의 낙차가 크고 잦은 폐기물 소각시설 등에서 효과적일 것으로 예상된다.

• 대한기계학회논문집B
• /
• 제27권10호
• /
• pp.1412-1419
• /
• 2003

Heat regenerator occupied by regenerative materials improves thermal efficiency of combustion system through the recovery of sensible heat of exhaust gases. By using one-dimensional two-phase fluid dynamics model, the unsteady thermal flow of regenerator with spherical particles, was numerically analyzed to evaluate the heat transfer and pressure losses and to derive the design parameter for heat regenerator. It is confirmed that the computational results, such as air preheat temperature, exhausted gases outlet temperature, and pressure losses, agreed well with the experimental data. The thermal flow in heat regenerator varies with porosity, configuration of regenerator and diameter of regenerative particle. As the gas velocity increases with decreasing the cross-sectional area of the regenerator, the heat transfer between gas and particle enhances and pressure losses decrease. As particle diameter decreases, the air is preheated higher and the exhaust gases are cooled lower with the increase of pressure losses. Assuming a given exhaust gases temperature at the regenerator outlet, the regenerator need to be linearly lengthened with inlet Reynolds number of exhaust gases, which is defined as a regenerator design parameter.

• Journal of Advanced Marine Engineering and Technology
• /
• 제37권3호
• /
• pp.282-290
• /
• 2013

A primary air pollutant as an indicator of air quality released from incomplete combustion is Carbon monoxide. A study of the distributions of CO concentration with no heat source in a tunnel model closed at left end side is simulated with a commercial CFD code. The tunnel model is used to investigate the CO concentration distributions at three Reynolds numbers of 990, 1970, and 3290. which are computed by the inlet velocities of 0.3, 0.6 and 1.0 m/s. The CFD predictive approaches can be useful for a better design to analyze the distributions of CO concentrations. In the case of the tunnel model closed at left end side alone, the concentration changes of x/H=-5 and -2.5 have the similar laminar characteristics like the case of the tunnel model closed at both end sides expecially at low values of Reynolds number. Irregular average CO concentration variations at Re=1790 are considered that the transition from laminar to turbulent flow occurs even in three different tunnel models.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.74-77
• /
• 2011

고성능 다단연소방식 액체 로켓엔진에 사용되는 기체 중심 스월 동축형 분사기의 리세스 길이 변화에 따른 혼합특성을 수치해석을 통해 연구를 수행하였다. 실제 추진제의 상(phase)은 기체(산화제)-액체(연료)형이지만, 모사조건을 통해 기체-기체로 고려하였다. 추진제의 확산각도를 측정하기 위해 분사기 출구에서의 속도 분포 및 추진제의 분무형상을 분석하였다. 리세스 길이가 증가함에 따라 축방향 속도는 증가하는 반면, 탄젠셜 방향 속도는 감소하였다. 이 결과 확산각도가 감소하는 정성적인 특징을 확인하였다.

• 한국수소및신에너지학회논문집
• /
• 제20권4호
• /
• pp.352-359
• /
• 2009

KEPRI is developing a Korean type coal-gasification system and the scale is 20 ton/day. Prior to this pilot plant, a 1 ton/day class gasification system will be used for pre-testing of several coal types. This paper introduces the configuration and design conditions of this 1 ton/day class system, presenting the gas/coal ratio, oxygen/coal ratio, cold gas efficiency, CFD analysis of gasifier, and others. The existing combustion furnace for residual oil was retrofitted as a coal gasifier and a vertical and down-flow type burner was manufactured. Ash removal is carried out through a water quencher and a scrubber following the quencher, and the sulfur is removed by adsorption in the activated carbon tower. The gas produced from the gasifier is burned at the flare stack. In this paper, the results of design conditions and initial operation conditions of I ton/day gasification system are compared together.

• 한국분무공학회지
• /
• 제18권2호
• /
• pp.100-105
• /
• 2013

While variable valve actuation or variable valve lift (VVL) is used increasingly in spark ignition (SI) engines to improve the volumetric efficiency or to reduce the pumping losses, it is necessary to understand the impact of variable valve lift and timing on the in-cylinder gas motions and mixing processes. In this paper, characteristics of the in-cylinder flow and fuel distribution for various valve lifts (4, 6, 8, 10 mm) were simulated in a GDI engine. It is expected that the investigation will be helpful in understanding and improving GDI combustion when a VVL system is used. The CFD results showed that a increased valve lift could significantly enhance the mixture and in-cylinder tumble motion because of the accelerated air flow. Also, it can be found that the fuel distribution is more affected by earlier injection (during intake process) than that of later injection (end of compression). These may contribute to an improvement in the air-fuel mixing but also to an optimization of intake and exhaust system.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 전기학술대회논문집
• /
• pp.205-209
• /
• 2005

Now a days Automobiles are becoming more important in our life, the study on piston of engine is needed because, piston's cooling and lubrication of piston have an effect on the life and efficiency of engine directly. So, this study is about nozzle part of oil jet for cooling piston in the automotive engine. Piston exposes combustion gas of over $2000^{\circ}C$ and is shocked high pressure at the time of explosion shortly. Furthermore strong friction occurs by high speed rotation. The cooling system is considered from oil jet to piston. The previous system cooled the lower part of piston only. So, efficiency was low. To improve this system, make the oil gallery in the piston, and oil flows into the gallery. The value of oil flow rate into the gallery is important. Consequently, the point of this study is the research of investigation of flow characteristics for variable Re number. This study has been modelled by a commercial CFD code FLUENT, allowing to assess its validity

• 대한기계학회논문집B
• /
• 제41권8호
• /
• pp.545-552
• /
• 2017

본 연구에서는 1 kW급 가정용 열병합 시스템의 원동기로 설계된 스털링 엔진의 고온 열교환기에 대하여 Fin 길이, 간격, 각도 등을 조정한 새로운 형상 및 기존 형상에 대하여 수치해석을 수행하여 형상 개선에 따른 성능 향상을 확인하였다. 형상을 개선하는 과정에서 고려하지 않았던 공기예열기를 포함하여 수치해석을 수행한 결과 실린더 헤드 부분에서 음의 열유속이 발생하는 현상이 관찰되었다. 배가스 온도 및 연소실 벽면 온도를 분석하여 이 현상을 규명하였다. 다음으로 이상적인 사이클을 가정하여 형상 개선에 의한 열전달량 증가가 열역학적 사이클 및 시스템 성능에 미치는 영향을 예측하였다.

• International Journal of Automotive Technology
• /
• 제8권5호
• /
• pp.575-581
• /
• 2007

As current and future automobile emission regulations become more stringent, the research on flow distribution for an exhaust manifold and close-coupled catalyst(CCC) has become an interesting and remarkable subjects. The design of a CCC and exhaust manifold is a formidable task due to the complexity of the flow distribution caused by the pulsating flows from piston motion and engine combustion. Transient flow at the exhaust manifold can be analyzed with various computational fluid dynamics(CFD) tools. However, the results of such simulations must be verified with appropriate experimental data from real engine operating condition. In this study, an experimental approach was performed to investigate the flow distribution of exhaust gases for conventional cast types and stainless steel bending types of a four-cylinder engine. The pressure distribution of each exhaust sub-component was measured using a simulated dynamic flow bench and five-hole pitot probe. Moreover, using the results of the pitot tube measurement at the exit of the CCC, the flow distribution for two types of manifolds(cast type and bending type) was compared in terms of flow uniformity. Based on these experimental techniques, this study can be highly applicable to the design and optimization of exhaust for the better use of catalytic converters to meet the PZEV emission regulation.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.150-156
• /
• 2008

A program based on a 2-D CFD code has been developed to simulate a gas turbine engine. 2-D Navier-Stokes implicit code with $k-\omega$ turbulent model is used in compressor and turbine. Lumped method chemical equilibrium code with 10 species of molecular is applied to combustor with assuming perfect mixture and 100% combustion efficiency at constant pressure state. Fluid properties are shared on interfaces between engine components. Compressor supplies outlet temperature and pressure to combustor. At the same time, combustor also carries temperature and pressure to turbine. The back pressure of compressor outlet is transferred by inlet pressure of turbine. Unsteady phenomena in rotor-stator are covered by mixing-plane method. The running condition of engine can be determined only by given the inlet condition of compressor, the outlet condition of turbine, equivalence ratio and rotating speed.