• 한국구조물진단유지관리공학회 논문집
• /
• 제22권2호
• /
• pp.98-104
• /
• 2018

콘크리트 비파괴강도 추정식은 일반적으로 콘크리트 강도를 결정하는데 사용된다. 그러나 기존의 추정식들은 대부분 제한된 실험 변수를 토대로 제안되어 배합조건, 강도특성 등이 다양한 실제 공용중 교량의콘크리트 압축강도 추정시 많은 오류를 포함한다. 본 연구에서는 297개 공용 교량의 정밀안전진단 결과 중 콘크리트 비파괴시험 및 현장 코어강도 시험결과를 토대로 콘크리트 부재의 코어강도와 비파괴 추정강도 평가결과를 비교분석하였다. 분석결과 분석이 이루어진 기존 추정식들 중 일본건축학회 CNDT소위원회 강도계산식이 다른 추정식에 비하여 실제파괴강도와의 오차가 가장적고 상관분석의 신뢰도도 가장높은 것으로 검토되었다. 그러나 이 추정식은 코어강도가 30 MPa이상일때 추정강도는 과소평가되는 것으로 나타났다. 이에 본 논문에서는 추정식에 의한 강도와 현장 코어강도사이의 관계를 활용하여 회귀분석을 통한 개선된 비파괴강도 추정식을 제안하였다.

• 한국농공학회지
• /
• 제35권4호
• /
• pp.55-66
• /
• 1993

Upon freezing a soil swells due to phase change and its compression stress increase a lot. As the soil undergo thawing, however, it becomes a soft soil layer because the 'soil changes from a solid state to a plastic state. These changes are largely dependent on freezing temperature and repeated freezing-thawing cycle as well as the density of the soil and applied loading condition. This study was initiated to describe the effect of the freezing temperature and repeated freezing-thawing cycle on the unconfined compressive strength. Soil samples were collected at about 20 sites where soil structures were installed in Kangwon provincial area and necessary laboratory tests were conducted. The results could be used to help manage effectively the field structures and can be used as a basic data for designing and constructing new projects in the future. The results were as follows ; 1. Unconfined compressive strength decreased as the number of freezing and thawing cycle went up. But the strength increased as compression speed, water content and temperature decreased. The largest effect on the strength was observed at the first freezing and thawing cycle. 2. Compression strain went up with the increase of deformation speed, and was largely influenced by the number of the freezing-thawing cycle. 3. Secant modulus was responded sensitivefy to the material of the loading plates, increased with decrease of temperature down to - -10$^{\circ}$C, but was nearly constant below the temperature. Thixotropic ratio characteristic became large as compression strain got smaller and was significantly larger in the controlled soil than in the soil treated with freezing and thawing processes 4. Vertical compression strength of ice crystal(development direction) was 3 to 4 times larger than that of perpendicular to the crystal. The vertical compression strength was agreed well with Clausius-Clapeyrons equation when temperature were between 0 to 5C$^{\circ}$, but the strength below - 5$^{\circ}$C were different from the equation and showed a strong dependency on temperature and deformation speed. When the skew was less then 20 degrees, the vertical compression strength was gradually decreased but when the skew was higher than that, the strength became nearly constant. Almost all samples showed ductile failure. As considered above, strength reduction of the soil due to cyclic freezing-thawing prosses must be considered when trenching and cutting the soil to construct soil structures if the soil is likely subject to the processes. Especially, if a soil no freezing-thawing history, cares for the strength reduction must be given before any design or construction works begin. It is suggested that special design and construction techniques for the strength reduction be developed.

• 한국농공학회지
• /
• 제20권1호
• /
• pp.4575-4591
• /
• 1978

In order to investigate the effects of grain size distribution, cement content, and molding pressure on the strength and durability of soil-cement mixtures, a laboratory test of soil cement mixtures was performed at four levels of cement content, five levels of molding pressure, and four levels of normal curing periods. The results are summarized as follows: 1. Optimum moisture contents in loam soil and maximum dry density in sand soil increased with the increase of cement content, but in others, both optimum moisture contents and maximum dry density were changed ununiformly. 2. When the specimens were molded with molding pressure, 50kg/$\textrm{cm}^2$, strength of soil cement mixture with cement content, 2 and 4 per cent, was lower than the strength of soil cement mixture without cement content by more than 40 to 50 per cent. 3. The strength of soil-cement molded with molding pressure, 100kg/$\textrm{cm}^2$, was higher than the strength of soil-cement molded with M.D.D. obtained from standard compaction test more than 40 per cent in sand loam cement and 50 per cent in loamy cement. 4. There was highly significant positive correlation among molding pressure, cement content and unconfined compressive strentgh and so the following multiple regression equations were obtained. Loam: fc=1.9693C+0.197P-0.84 Sandy loam: fc=2.9065C+0.235P-0.77 5. When the specimens were molded with molding pressure, 20 to 100kg/$\textrm{cm}^2$, the regression equation between the 28-day and 7-day strenght was obtained as follows. Loam : q28=1.1050q7+7.59(r=0.9147) Sandy loam : q28=1.3905q7+3.17 (r=0.9801) 6. At the cement contents of above 50 per cent, the weight losses by freeeze-thaw test were negligible. At the cement content of below 8 per cent the weight losses were singnificantly high under low molding pressure and remarkably decreased with the increase of molding pressure up to 80kg/$\textrm{cm}^2$. 7. Resistance to damage from water and to absorption of water were not improved by molding pressure alone, but when the soil was mixtured with cement above 6 per cent, damage seldoms occurred and absorbed less than 5 per cent of water. 8. There was highly significant inverse-corelationship between the compressive strength of soil cement mixtures and their freeze-thaw loss as well as water absorption. By the regression equation methods, the relationships between them were expessed as followed fc=-7.3206Wa+115.6(r=0.9871) log fc=-0.0174L+1.59(r=0.7709) where fc=unconfined compressive stregth after 28-days curing. kg/$\textrm{cm}^2$ Wa=water absorption, % L : freeze-thaw loss rate, %

• 한국구조물진단유지관리공학회 논문집
• /
• 제21권2호
• /
• pp.114-121
• /
• 2017

본 연구는 플라이애시 및 고로슬래그 미분말을 알칼리 활성화 결합재로 활용하여 제조한 모르타르의 압축강도 특성을 파악하고 건조수축 예측 및 평가가 가능한 추정식을 제안하고자 한다. 이를 위하여 고로슬래그 미분말 치환량을 30, 50, 70 및 100%로 조정하고 규산나트륨 모듈 Ms비[$SiO_2/Na_2O$]은 1.0, 1.5 및 2.0으로 조정하여 압축강도 및 길이변화율을 측정하였다. 그 결과 알칼리 활성화 결합재 모르타르는 Ms비가 증가할수록 압축강도는 증가하고 길이변화율은 감소하였다. 그러나 고로슬래그 미분말의 경우에는 치환량을 증가할수록 압축강도는 증가하였으나 길이변화율도 증가하는 경향이 확인되었다. 따라서, 고로슬래그 미분말을 다량 치환할 경우에는 길이변화율을 고려하여 설계할 필요성이 있다고 판단되었다. 알칼리 활성활 결합재 모르타르의 건조수축을 평가하는 식을 유도하기 위하여 배합조건별 단순회귀분석을 수행한 결과 결정계수 0.7539~0.9786(평균 0.9359)수준의 유효한 추정식을 도출하였다. 또한, 고로슬래그 미분말, Ms비 및 재령을 독립변수로 선정하여 다중회귀분석을 수행한 결과 초기양생온도 $23^{\circ}C$ 및 $70^{\circ}C$에서 결정계수 0.8020 및 0.8018 수준의 타당한 추정식을 제안하였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제19권3호
• /
• pp.122-129
• /
• 2015

본 연구에서는 일반강도 슬래브가 기둥 사이로 지나가는 형태의 모서리 기둥에 대한 유효압축강도 예측식을 개발하고자 하였다. 예측식 개발을 위해서 고강도 기둥-일반강도 슬래브 접합부와 조적조 구조의 유사성을 이용하였으며, 이에 더하여 기둥 단면치수에 대한 슬래브 두께의 형상비를 고려하였다. 제안된 식에 의한 예측값과 실험값의 비교를 통해 신뢰도를 확인하였으며, 설계기준 및 타 연구자들에 의한 제안식과 비교를 통해 우수성을 검증하였다. 연구결과, 제안식은 예측치에 대한 실험값의 비가 평균 1.02, 표준편차 0.15를 보여 콘크리트 구조기준 (2012)을 포함한 타 유효압축강도 예측식들에 비해 정확도 및 일관성 모두 우수한 결과를 나타냈다.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권4호
• /
• pp.327-333
• /
• 1997

Experiments on mechanical fatigue were conducted using the specimens which were cut from hydrogen cooled generator(rated 22kV and 50OMW) stator windings. We have investigated the aged mechanism of mica/epoxy insulation systems under air or hydrogen by both the tensile and compressive loadings. The fracture of generator stator windings is generally affected by mechanical stress. Thus, the tensile strength test were conducted. In this case, the maximum strength and strain are quite different between sound and aged specimens. It is observed that low bonded interface parts of tapes generally have lower strength than those of normal tapes which causes stress. In order to estimate the effects of cyclic load by the electromagnetic forces while the generator starts/stops, the mechanical fatigue test was also conducted. It is confirmed that the equation of expected life depends on stress amplitude and number of cycles. Though the stress amplitude and number of cycles are very tiny, the tensile fatigue of aged specimens under hydrogen atmosphere is bigger than those under air. In the case of hydrogen atmosphere, the tensile stress gives bigger effect than the compressive one.

• Structural Engineering and Mechanics
• /
• 제24권2호
• /
• pp.137-154
• /
• 2006

The reliable pushover analysis of RC structures requires a realistic prediction of moment-curvature relations, which can be obtained by utilizing proper constitutive models for the stress-strain relationships of laterally confined concrete members. Theoretical approach of Mander is still a single stress-strain model, which employs a multiaxial failure surface for the determination of the ultimate strength of confined concrete. Alternatively, this paper introduces a simple and practical failure criterion for confined concrete with emphasis on introduction of significant modifications into the two-parameter Drucker-Prager model. The new criterion is only applicable to triaxial compression stress state which is exactly the case in the RC columns. Unlike many existing multi-parameter criteria proposed for the concrete fracture, the model needs only the compressive strength of concrete as an independent parameter and also implies for the influence of the Lode angle on the material strength. Adopting Saenz equation for stress-strain plots, satisfactory agreement between the measured and predicted results for the available experimental test data of confined normal and high strength concrete specimens is obtained. Moreover, it is found that further work involving the confinement pressure is still encouraging since the confinement model of Mander overestimates the ultimate strength of some RC columns.

• 한국지반환경공학회 논문집
• /
• 제19권8호
• /
• pp.5-10
• /
• 2018

본 연구는 암석표면 타격 시 발생하는 사운드압력에 대한 응답신호를 모두 측정하고 이를 누적한 전체 사운드 신호에너지를 이용하여 화강편마암의 압축강도를 비파괴적으로 산정하는 방법과 그 결과를 제시하는 것이다. 이를 위해서 다수의 화강편마암 암석시편을 준비하였고 각 시편에 대하여 고안된 타격장치(회전 자유낙하에 의한 초기타격 및 반발작용에 의한 연속적인 반복타격 가능 장치)를 이용하여 타격하고 타격 시 발생한 모든 사운드압력을 시간에 따른 신호로서 측정하였다. 암석시편별 측정된 사운드 신호를 모두 누적하고 그 값(전체 사운드 신호에너지라 명명함)을 암석시편별 직접 측정된 압축강도와 상호 비교하였다. 비교결과, 화강편마암의 각 시편에 대해서 타격을 통해 얻어진 전체 사운드 신호에너지는 해당 시편의 직접압축강도와 직접적인 비례관계가 있다는 것을 확인하였으며, 또한 전체 사운드 신호에너지를 이용한 강도예측식을 이용하여 화강편마암의 압축강도를 90% 이상 신뢰성 있게 예측할 수 있음을 파악하였다. 더 나아가 본 연구결과를 통해 향후 다양한 암석 및 콘크리트 등의 압축강도는 전체 사운드 신호에너지를 이용하여 비파괴적으로 예측할 수 있을 것으로 판단된다.

• 지질공학
• /
• 제14권3호
• /
• pp.273-285
• /
• 2004

본 연구에서는 전라남도 고흥군 일대에 분포하는 중생대 백악기 응회암을 대상으로 실내 시험을 통하여 역학적 특성을 파악하였다. 고흥군 일대에 분포하는 응회암(고흥응회암, 팔영산 용결응회암)은 성분상 glass성분이 우세한 유리 질응회암(vitric tuff)에 해당된다. 응회암의 물리적 특성인 비중, 건조밀도, 함수율, 공극율 및 흡수율의 평균값은 각각 2.51, $2.52(g/cm^2)$, 0.12($\%$), 4.51($\%$) 및 1.91($\%$)이다. 공극율의 증가에 따라 건조밀도는 낮아지는 경향을 보이며, 흡수율과 공극율은 밀접한 상관관계를 보인다. 일축압축강도(UCS) 범위는 80.4$\~$208(MPa), 평균 141.1(MPa)로서 Deere & Miller(1966)에 의한 신선한 암의 공학적 분류에 의하면 high strength에 해당이 된다. 축방향의 점하중 강도지수($Is_a$)는 평균 4.2(MPa)이며, 직경방향 점하중 강도지수($Is_d$)는 평균 2.2(MPa)으로, 점하중강도 이방성지수($Ia_{(50)}$)는 1.93이다. 일축압축강도와 축방향 점하중 강도지수($Is_{(50)}$)는 밀접한 선형관계를 보이며, 관계식은 UCS=22 $Is_{(50)}$ +49 (MPa) (r=0.95) 로 나타낼 수 있다. 이 식은 고흥 지역 응회암에 대한 일축압축강도를 예측하는데 유용하게 사용할 수 있다.

• Tribology and Lubricants
• /
• 제38권1호
• /
• pp.22-26
• /
• 2022

A 1.7-ton grade small excavator is a construction equipment that can perform various functions in limited spaces where heavy equipment cannot enter easily. Owing to the recent acceleration of urbanization, it has been used increasingly in drainage and gas pipes, as well as for road repair works in urban areas. The power train of a traveling reducer for a 1.7-ton grade small excavator utilizes a complex planetary gear system. Complex planetary gears are vital to the power train of a traveling reducer as it mitigates the fatigue strength problem. In the present study, the specifications of a complex planetary gear train are calculated; furthermore, the gear bending and compressive stresses of the complex planetary gears are analyzed to achieve an optimal design of the latter in terms of cost and reliability. In this study, the actual gear bending and compressive stresses of a planetary gear system are analyzed using a self-developed gear design program based on the Lewes and Hertz equation. Subsequently, the calculated specifications of the complex planetary gears are verified by evaluating the results with the data of allowable bending and compressive stress based on curves of stress vs. number of cycles of the gears.