• Composites Research
• /
• 제19권4호
• /
• pp.23-30
• /
• 2006

극저온 추진제 탱크를 개발하는 과정에서 복합재와 알루미늄 라이너를 접합하기 위한 접착제의 선택은 탱크의 안전성과도 직결된 매우 중요한 문제이다. 따라서 적합한 극저온용 접착제를 선택하기 위해 3종류의 접착필름이 선정되었으며 극저온용으로 개발된 탄소섬유/에폭시와 라이너 재료로 사용되는 알루미늄으로 구성된 양면 겹치기 조인트 시편을 제작하였다. 제작된 시편을 극저온 환경챔버를 사용하여 상온과 $-150^{\circ}C$에서 인장실험을 수행하여 각 접착제의 접착강도를 비교하였으며 파손 특성을 분석하였다. 또한 양면 겹치기 조인트 시편의 각 구성재료의 온도에 따른 기계적 물성변화를 측정하였으며 이를 이용하여 ABAQUS를 통한 유한요소해석을 수행하여 양면 겹치기 조인트 시편의 인장시험결과를 분석하였다.

• Restorative Dentistry and Endodontics
• /
• 제21권1호
• /
• pp.227-241
• /
• 1996

The effect of collagen dissolution in acid conditioned dentin was morphologically examined by both scanning and transmission electron microscopy. 18 freshly extracted human molars and dentin bonding systems of All Bond 2, Scotchbond Multipurpose, Superbond D-Liner were used in this study. For SEM preparation, each 3 of ~ exposed dentin surfaces were acid conditioned by using various acids within the above three bonding systems respectively. After acid conditioning of the other 3 exposed dentin surfaces as above, they were treated with 1.7% NaOCl for 2 minutes. The remaining 3 dentin surfaces were acid conditioned and treated with 3.3 % NaOCl for 2 minutes. All of the specimens were then fixed in 4 % glutaraldehyde for 12 h at $4^{\circ}C$ and dehydrated in ethanols grades from 50 % to 100 %, then surface changes of the specimens were observed by using SEM. For TEM preparation, exposed dentin surfaces were acid conditioned with the same acid as SEM specimens and treated with 1.7%, 3.3 % NaOCl respectively, then applied with corresponding bonding agents. After the procedures were finished, composite resin were applied on the dentin surfaces and light cured. Small, rectangular sticks with end dimensions of approximately 1 by 1 mm were sectioned and further sample preparative techniques for transmission electron microscopy were performed in accordance with the procedures used for ultrastructural TEM observations of calcified tissues. The results were as follows : 1. In the 1.7 % NaOCl retreated specimens after acid conditioning, the porous dentin surface of intertubular dentin and wide opening of dentinal tubules were appeared. And there were fine irregularities on the intertubular dentin, indicating a clear difference as compared with the acid conditioned specimens. 2. In the 3.3% NaOCl retreated specimens after acid conditioning, the intertubular dentin was further eroded causing a more porous and wider opening of dentinal tubules. Moreover, sharp irregularities on the intertubular dentin were more evident than those of acid conditioned and 1.7% NaOCl retreated specimens. 3. In all of the acid conditioned specimens, the resin-dentin hybrid layer of approximately 3.5mm thickness was formed and the collapsed collagen layer was observed on the uppermost part of hybrid layer in the specimens applied with All Bond 2. The collgen fibrils of intertubular dentin in specimens applied with Scotchbond Multipurpose were running perpendicular to the interface, and electron dense black layer demarcated from the deep unaltered dentin was more evident in the specimen applied with Superbond D-Liner than any other specimens. 4. In the 1.7 % NaOCl retreated specimens after acid conditioning, the resin-dentin hybrid layer of approximately 2.5-3.0mm thickness was formed and the collapsed collagen layer and longitudinally running collagen fibrils as shown in the acid conditioned specimens were observed in the specimens applied with All Bond 2 and Superbond D-Liner. 5. In all of the 3.3% NaOCl retreated specimens after acid conditioning, the evidence of resin-dentin hybrid layer was not identified ; nevertheless, the longitudinally running collagen fibrils remained slightly in the specimens applied with All Bond 2.

• Restorative Dentistry and Endodontics
• /
• 제20권2호
• /
• pp.856-868
• /
• 1995

The effect of collagen dissolution in acid conditioned dentin layer on resin - dentin adhesion was investigated. 160 freshly extracted human molars were divided into 4 groups randomly and dentin surfaces were exposed. 40 exposed dentin surfaces were not acid conditioned and each 10 of them were applied with bonding agents within dentin bonding systems of All Bond 2, Scotchbond Multipurpose, Clearfil Photobond and Superbond D - Liner respectively. Each 10 of another 40 exposed dentin surfaces were acid conditioned by the acid within the above four bonding systems respectively and applied with corresponding bonding systems. After acid conditioning of the other 40 exposed dentin surfaces as above, they were treated with 5% NaOCl for 2 minutes, and each 10 of them were applied with the above four dentin bonding systems respectively. The remaining 40 dentin surfaces were acid conditioned and treated with 10% NaOCl for 2 minutes, and each 10 of them were applied with corresponding bonding agents as the above. After the procedures were finished, composite resin (Z -100, 3M Dent. Prod., USA) were applied on the dentin surfaces and light cured. Shear bond strength values were measured. Surface changes of fractured dentin specimens were observed using SEM (Hitachi S-2350, Japan). The following results were obtained. 1. In all of dentin bonding systems, shear bond strengths of non - conditioned specimens were significantly lower than those of acid conditioned specimens (P<0.05). 2. A statistically significant difference of bond strengths did not exist between acid conditioned specimens and 5% NaGCI retreated specimens applied with All Bond 2, Scotchbond Multipurpose and Clearfil Photobond (P>0.05). However, strength values of 5% NaOCl retreated specimens applied with Superbond D - Liner were lower than those of acid conditioned specimens (P<0.05). 3. In all the applied dentin bonding systems except Clearfil Photobond, bond strengths of 10% NaOCl retreated specimens were lower than those of acid conditioned and 5% NaOCl retreated specimens (P<0.05). 4. The resin - dentin hybrid layer of 4 - $5{\mu}m$ thickness was formed in the acid conditioned specimens applied with All Bond 2, Scotchbond Multipurpose and Superbond D-Liner. 5. The resin - dentin hybrid layer of 3 - $4{\mu}m$ thickness was still formed in the 5% NaOCl retreated specimens applied with All Bond 2 and Scotchbond Multipurpose. In addition, this layer was not completely removed after the retreatment with 10% NaOCl. Above results indicate that the dissolution of collagen in acid conditioned dentin layer by NaOCl solution can not be achieved completely and the collagens contribute to the resin - dentin adhesion considerably.

• Journal of the Korean Wood Science and Technology
• /
• 제12권3호
• /
• pp.3-8
• /
• 1984

섬유의 방향성이 무질서한 composites에 적용되는 Smith와 Cox의 이론(理論)을 포함한 Paul과 Jones의 혼합이론식(混合理論式)은 유황(硫黃) 화합물(化合物)을 사용하여 제조한 목재섬유 복합재(複合材)에도 일차적(一次的)인 liner regression constant가 주어질 때는 사용할 수가 있음을 보여준다. $E_c=\frac{1}{3}aE_fV_f+bE_mV_m$으로 표시된 이 liner regression from에 math. rom pack을 사용한 Hewlett Packard 75C(HP 75C) computer의 계산 결과는 목재 섬유 복합재(複合材)에 사용된 matrix의 종류, 섬유판의 밀도와 목재 밑 목질 섬유의 종류에 관계없이 a=3.27~3.54와 b=-2.47~-2.80의 일정한 범위의 값을 보여주므로, 지금까지 무(無)질서한 방향성을 지닌 장(長)섬유로 된 복합재(複合材)에만 적용되어 왔던 Paul과 Jones의 혼합이론(混合理論)과 이것과 같은 방향을 지닌 단(短) 섬유로 된 목재(木材)나 목질(木質) 섬유 composites에도 적용될 수 있음을 증명하고 있다.

• 비파괴검사학회지
• /
• 제35권5호
• /
• pp.332-340
• /
• 2015

음향방출기술은 고체내부에 국부적으로 형성된 변형에너지가 급격히 방출되면서 발생하는 탄성파를 이용하는 기술로써 결함의 발생이나 존재하는 결함의 진전을 검출하는 비파괴검사 기법이다. 환경문제로 인해 최근 약 20년 전부터 압축 천연 가스가 자동차 석유 연료의 대안으로 사용되면서 CNG 탱크의 안전성 검사의 필요성 또한 증가하고 있다. 특히 복합재 CNG 탱크에서는 적층된 재료와 방향에 따라 파의 속도나 분산 특성이 달라지므로 매질의 속도에 절대적으로 영향을 받는 종래의 도달 시간차를 이용한 AE 기법으론 결함검출을 하는데 한계가 있다. 따라서 본 연구에서는 스틸실린더인 Type-I과 스틸실린더에 GFRP로 와인딩된 Type-II 시편에서 에너지 기반 contour map 기법을 이용해 종래의 AE기법의 한계를 극복하고 결과를 비교하였다. 그 결과 위치표정이 불가하거나 오차가 컸던 종래의 방법과 달리 에너지 기법은 모든 지점에서 위치표정이 가능했으며 오차 또한 현저히 준 것을 확인할 수 있었다.

• Restorative Dentistry and Endodontics
• /
• 제35권2호
• /
• pp.116-124
• /
• 2010

본 연구에서는 복합 레진을 이용한 2급/5급 와동의 직접수복에 있어서 치과의사의 성별에 따른 술식의 차이를 비교하였다. 2008년 대한치과의사협회에 등록된 치과의사 12,193명을 대상으로 이 메일을 통한 설문조사를 실시하였다. 이 메일 수신이 확인된 2,632명 중 840명이 응답하였으며 응답자의 남녀 비율은(남 78.9%, 여 21.1%) 전체 치과의사의 남녀 비율과 유의한 차이를 보이지 않았다(p > 0.05). Chi-square test 와 multiple logistic regression analysis 를 이용하여 남녀간 술식의 차 이를 검증하였다. 2급 와동 수복에서 여자치과의사는 4회 이상의 적층 분할 수복을 하는 경향이 남자치과의사에 비해 1.87배 높았으며, 술식 당 30분 이상 소요하는 경향은 2.72배 높았다(p < 0.05). 5급 와동 수복에서 여자치과의사는 베이스를 사용하는 경향이 1.83배 높았으며, 술식 당 20분 이상 소요하는 경향은 1.63배 높았다(p < 0.05). 본 설문조사에 따르면 남녀 성별에 따라 복합 레진 수복 술식의 차이가 존재하는 것으로 나타났다.

• 한국항공우주학회지
• /
• 제35권7호
• /
• pp.592-600
• /
• 2007

최근에 발사체의 경량화를 위해 추진제 탱크의 재료를 복합재료로 대체하기 위한 연구가 많이 진행되고 있다. 본 연구에서는 극저온용으로 개발된 복합재와 알루미늄 라이너로 구성된 타입 3 추진제 탱크를 제작하고 실제 극저온 상태의 운용환경을 고려한 실험을 수행하였다. 이를 위해 액체 질소를 제작된 타입 3 탱크에 주입하고 기체 질소를 이용하여 가압하였다. 실험수행과정에서 헬리컬 층과 후프 층 사이에서 층간 분리 현상이 관찰되었으며, 이에 대한 원인을 분석하기 위해 해석적 방법과 실험적 방법이 사용되었다. 해석적 방법에서는 점진적 파손 해석을 고려한 열탄성 해석으로부터 파손 지수를 평가하였으며 실험적 방법에서는 타입 3 탱크를 쉽게 모사할 수 있는 복합재/알루미늄 링 시편의 액체질소 담금 시험을 통해 헬리컬 층과 후프 층 사이의 계면을 관찰하였다.

• Imaging Science in Dentistry
• /
• 제30권4호
• /
• pp.243-248
• /
• 2000

Purpose: The aim of this study was to determine the relative radiopacities of cavity lining materials (Resin-modified Glass Ionomer cement, Compomer and Plowable resin) for posterior composite resin restoration. Material & Methods: Resin-modified glass ionomer cement (Fuji II LC, Vitrebond/sup TM/), Compomers (Dyract /sup (R)/ Compoglass, F2,000, Dyract/sup (R)/ flow Compoglass Flow) and Flowable resins (Tetric/sup (R)/ flow, Aeliteflo/sup TM/ Revolution/sup TM/) were used. Five specimens of 5 mm in diameter and 2 mm thick were fabricated with each material. Human molars were horizontally sectioned 2 mm thick to include both enamel and dentin. The radiopacities of enamel, dentin, cavity lining materials, aluminum step wedge were obtainded from conventional radiograph and NIH image program. Results: All the tested lining materials showed levels of radiopacity the same as or greater than that of dentin. All compomer tested (Dyract, Compoglass, F2,000, Dyract flow, Compoglass Flow) and Vitrebond/sup TM/, Tetric/sup (R)/ flow were more radiopaque than enamel. The radiopacities of Fuji II LC and Revolution/sup TM/ were between enamel and dentin and resin-modified glass ionomer cement, Compomer and Tetric/sup (R)/ flow were greater than those of Revolution/sup TM/, Aeliteflo/sup TM/ or dentin. The level of radiopacity of the tested materials was variable; those with low radiopacity should be avoided in class II restorations, where a clear determination of recurrent caries by the examining clinician could be compromised. Conclusion: Clinician should be able to distinguish these cavity lining materials radiographically from recurrent decay, voids, gaps, or other defects that lead to clinical failure. Utilization of materials ranked more radiopaque than enamel would enable clinicians to distinguish the lining material from tooth structure.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권2호
• /
• pp.139-145
• /
• 1998

Filament winding method is widely used for composite fabrications using low viscosity liquid for-mation and processing asymmetrical structures of pressure vessel pipe rocket motor case etc. The filament winding method is affected by several parameters such as pot life of process time viscosi-ty of resin filament winding temperature and schedules curing condition and post curing condi-tion of resin. To develope high functional composite materials the rotation(5, 15, 20, 30rpm) of the winding machine was controlled by D.C motor. And the wiper to give proper tension was equipped between strand and resin bath. The resin is hooked by the design wiper. The adequate cure schedule was found by DSC. NOL ring test is carried out to investigate the basic physical properties such as design technology. The void contents in filament winding is generally higher than that of the prepreg laminated plate. These high contents of void can make a crack in resin in spite of low deformation. These problem was solved by giving tension in processing. To improve the characteristics of fiber volume fraction void contents resin/fiber bonding the winding speedc is changed under constant tension. It was found that resin impregnation was not different from in fiber contents void contents at the range of 0.5~1kg tension but it was found that resin was not impregnated at the above of 1.5kg tension. In burst test a pure PE liner was failed at a nozzle part under the $14kg/\textrm{cm}^2$ pressure but a pressure vessel of CNG was failed at a cylinder part under the $200kg/\textrm{cm}^2$ pressure.

• Restorative Dentistry and Endodontics
• /
• 제26권2호
• /
• pp.153-161
• /
• 2001

The purpose of this study was to evaluate microleakage of six current dentin bonding systems. In this in vitro study, class V cavities were prepared on buccal and lingual surfaces of thirty extracted human molars. Each margin was on enamel and dentin/cementum. Experimental teeth were randomly divided into six groups of 5 each. Group 1 : Scotchbond Multi-Purpose; Group 2 : Single Bond; Group 3 : Prime&Bond NT ; Group 4 : Clearfil Liner Bond 2 ; Group 5 : MAC Bond II ; Group 6 : One-up Bond F. The bonding agent and composite resin were applied to class V cavities according to manufacturer's directions. After thermocycling, the specimens were immersed in 0.5% basic fuchsin dye solution for 6 hours and sectioned longitudinally through the center of the restoration with a low speed diamond saw. The degree of microleakage was measured as the extent of dye penetration under the stereomicroscope at $\times$20. The data were analyzed using one way ANOVA. When significant differences found. multiple comparisons were made using Duncan's Multiple Range Test. The results of this study were as follows: 1. In all groups, leakage value seen at the enamel margin was significantly lower than that seen at the dentin margin(P<0.001). 2. At the enamel margin, none of the dentin bonding systems used in this study showed statistically significant difference in leakage values(P<0.05). 3. At the cementum margin, group 3 showed the highest leakage value, and others were decreased as group 5, 6, 4 in that order, and group 1, 2 showed the lowest leakage value. There was statistically significant difference between group 3 and the other groups except for group 5(P<0.05).