• Steel and Composite Structures
• /
• v.51 no.4
• /
• pp.351-361
• /
• 2024

Accurate measurement of K_IC values for gas pipeline steels is important for assessing pipe safety using failure assessment diagrams. As direct measurement of K_IC was impossible for the API X70 pipeline steel, multi-specimen fracture tests were conducted to measure J_IC using three-point bend geometry. The J values were calculated from load-displacement (F-δ) plots, and the associated crack extensions were measured from the fracture surface of test specimens. Valid data points were found for the constructed J-Δa plot resulting in J_IC=356kN/m. More data points were added analytically to the J-Δa plot to increase the number of data points without performing additional experiments for different J-Δa zones where test data was unavailable. Consequently, displacement (δ) and crack-growth (Δa) from multi-specimen tests (with small displacements) were used simultaneously, resulting in the variation of Δa-δ (crack growth law) and δ-Δa obtained for this steel. For new Δa values, corresponding δ values were first calculated from δ-Δa. Then, corresponding J values for the obtained δ values were calculated from the area under the F-δ record of a full-fractured specimen (with large displacement). Given Δa and J values for new data points, the developed J-Δa plot with extra data points yielded a satisfactory estimation of J_IC=345kN/m with only a -3.1% error. This is promising and showed that the developed technique could ease the estimation of J_IC significantly and reduce the time and cost of expensive extra fracture toughness tests.

• Economic Analysis
• /
• v.25 no.2
• /
• pp.96-131
• /
• 2019

Initially entering into the job market during hard times with unfavorable market institutions has a persistent, negative effect on young workers' subsequent employment. This paper analyzes hysteresis in youth unemployment by using a composite fixed-effect panel data model. Data sets for the age-cohort unemployment rate and for labor market institutions are constructed from OECD statistics from 21 advanced economies, including Korea, from 1985 to 2017, and are then readjusted to match with the peculiarities of the Korean market. In Korea, with a less-aggressive stance on active labor market policy spending, a male worker who experiences a one percentage point higher youth unemployment rate when he was 20- to 29-years-old has a 0.146 percentage point higher unemployment rate at the ages of 30-to 34-years-old and a 0.035 percentage point higher unemployment rate at the age of 35- to 39-years-old. These figures are larger than those in most countries that have more aggressive spending schemes. These findings point out that hysteresis in the Korean labor market can be mitigated by expanding active labor market policy spending more aggressively and more effectively.

• Convergence Security Journal
• /
• v.8 no.3
• /
• pp.83-92
• /
• 2008

In respect complication of group and period, the sales of retail trade is composed of various factors. This paper studies focus on estimating the determinants of the sales of retail trade. The volume of analysis consist of 7 groups. Analyzing period be formed over a 36 point(2005. 1$\sim$2007. 12). In this paper dependent variable setting up sales of retail trade, explanatory(independent) variables composed of composite stock price index, the number of the consumer's online buying behavior company, the coincident composite index, the index of trading price of APT, employment rate, an average of the rate of operation(the manufacturing industry), the consumer price index. The result of estimating the determinants of sales of retail trade provides empirical evidences of significance positive relationships between the coincident composite index, the index of trading price of APT, employment rate, an average of the rate of operation(the manufacturing industry). However this study provides empirical evidences of significance negative relationships between the consumer price index. The explanatory variables, that is, composite stock price and the number of the consumer's online buying behavior company, are non-significance variables. Implication of these findings are discussed for content research and practices.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.54 no.4
• /
• pp.9-17
• /
• 2012

This study was aimed to characterize non-point source (NPS) pollutant runoff and estimate event mean concentrations (EMCs) from a small rural watershed located at the headwater area of the Gyeongan stream. The study watershed consists of the two major landuse, forest (72 %) and paddy field (28 %). The nine rainfall events ranging from 18.5 to 192.6 mm in amount were monitored in this study. Stream flow was measured at the watershed outlet using a water level gauge, while a number of water samples for each event were collected and analysed for water quality. Event pollutant loads varied greatly depending on rainfall events varying from 22.6 to 3,134.2 mg/L, 0.32 to 24.56 mg/L, 0.090 to 1.320 mg/L, and 2.3 to 149.8 mg/L for SS, TN, TP, and COD, correspondently. The respective mean EMCs were estimated by 104.2, 1.00, 0.168, and 7.9 mg/L. The Pearson correlation analysis showed that COD EMC was significantly correlated with those of SS, TN, and TP. Rainfall runoff ratio appeared to be negatively correlated with EMCs of SS, TP, and COD, although not statistically significant. The event loads from the largest rainfall was greater than the sum of those from the remaining eight events. The study results suggest that the appropriate management of intensified storm events are of greater importance in curbing NPS loads, while the estimated EMCs provide base data for the unit pollutant loads determination for the forest-paddy composite upstream watershed.

• Restorative Dentistry and Endodontics
• /
• v.33 no.1
• /
• pp.1-8
• /
• 2008

The purpose of this study was to evaluate the effect of a new resin monomer, filler size and polishing technique on the surface roughness of composite resin restorations using confocal laser scanning microscopy. By adding new methoxylated Bis-GMA (Bis-M-GMA, 2,2-bis[4-(2-methoxy-3-methacryloyloxy propoxy) phenyl] propane) having low viscosity, the content of TEGDMA might be decreased. Three experimental composite resins were made: EX1 (Bis-M-GMA/TEGDMA = 95/5 wt%, 40 nm nanofillers); EX2 (Bis-M-GMA/TEGDMA = 95/5 wt%, 20 nm nanofillers); EX3 (Bis-GMA/TEGDMA = 70/30 wt%, 40 nm nanofillers). Filtek Z250 was used as a reference. Nine specimens (6 mm in diameter and 2 mm in thickness) for each experimental composite resin and Filtek Z250 were fabricated in a teflon mold and assigned to three groups. In Mylar strip group, specimens were left undisturbed. In Sof-lex group, specimens were ground with #1000 SiC paper and polished with Sof-lex discs. In DiaPolisher group, specimens were ground with #1000 SiC paper and polished with DiaPolisher polishing points. The Ra (Average roughness), Rq (Root mean square roughness), Rv (Valley roughness), Rp (Peak roughness), Rc (2D roughness) and Sc (3D roughness) values were determined using confocal laser scanning microscopy. The data were statistically analyzed by Two-way ANOVA and Tukey multiple comparisons test (p = 0.05). The type of composite resin and polishing technique significantly affected the surface roughness of the composite resin restorations (p < 0.001). EX3 showed the smoothest surface compared to the other composite resins (p < 0.05). Mylar strip resulted in smoother surface than other polishing techniques (p < 0.05). Bis-M-GMA. a new resin monomer having low viscosity, might reduce the amount of diluent, but showed adverse effect on the surface roughness of composite resin restorations.

• Steel and Composite Structures
• /
• v.36 no.1
• /
• pp.75-86
• /
• 2020

The grid structures with welded hollow spherical joint (WHSJ) have gained increasing popularity for use in industrial buildings with suspended cranes, and usually welded with steel tube (ST). The fatigue performance of steel tube-welded hollow spherical joint (ST-WHSJ) is however not yet well characterized, and there is little research on fatigue life prediction methods of ST-WHSJ. In this study, based on previous fatigue tests, three series of specimen fatigue data with different design parameters and stress ratios were compared, and two fatigue failure modes were revealed: failure at the weld toe of the ST and the WHSJ respectively. Then, S-N curves of nominal stress were uniformed. Furthermore, a finite element model (FEM) was validated by static test, and was introduced to assess fatigue behavior with the hot spot stress method (HSSM) and the effective notch stress method (ENSM). Both methods could provide conservative predictions, and these two methods had similar results. However, ENSM, especially when using von Mises stress, had a better fit for the series with a non- positive stress ratio. After including the welding residual stress and mean stress, analyses with the local stress method (LSM) and the critical distance method (CDM, including point method and line method) were carried out. It could be seen that the point method of CDM led to more accurate predictions than LSM, and was recommended for series with positive stress ratios.

• Steel and Composite Structures
• /
• v.18 no.1
• /
• pp.29-50
• /
• 2015

With a quasi-three point bending apparatus, ratcheting deformation is studied experimentally on a pressurized austenitic stainless steel Z2CND18.12N pipe under bending load and vertical displacement control, respectively. The characteristic of ratcheting behavior of straight pipe under both control methods is achieved and compared. The cyclic bending loading and internal pressure influence ratcheting behavior of pressurized straight pipe significantly under loading control and the ratcheting characteristics are also highly associated with the cyclic displacement and internal pressure under displacement control. They all affect not only the saturation of the ratcheting strain but the ratcheting strain rate. In addition, ratcheting simulation is performed by elastic-plastic finite element analysis with ANSYS in which the bilinear model, Chaboche model, Ohno-Wang model and modified Ohno-Wang model are applied. By comparison with the experimental data, it is found that the CJK model gives reasonable simulation. Ratcheting boundaries under two control modes are almost same.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.3
• /
• pp.832-842
• /
• 1996

Fatigue life prediction and fatigue behavior of circular notched carbon fiber reinforced plastic laminates are presented. Point and average stress criteria by Whitney and Nuismer are generalized to fatigue fracture criteria for notched laminates. Residual strength degradation model and the assumptions on the stress redistribution are introduced during the derivation of prediction equations. S-N curve, Basquin's relation, and H and H's FLPE1 are chosen for evaluation of residual strength of unnotched laminates and six prediction equations are derived. Experiments are performed using Graphite/Epoxy laminates whose fiber orientation is $[0$^\circ$/+45$^\circ$/-45$^\circ$/90$^\circ$]s. Presented prediction equations are reasonably close to experimental data and proposed appoach is found to be suitable to predict fatigue life of notched composite laminates.

• Journal of The Korean Digital Architecture Interior Association
• /
• v.12 no.1
• /
• pp.71-79
• /
• 2012

This study aims at finding relationships between the competitiveness of cities and the size or distance of them, based on some premises; (1) the competitiveness can be measured on the interval-ratio level, that is, factor scores, (2) a hypothesis that the spatial interaction model is valid for the relationships can be generally accepted. Based on the general recognition a research hypothesis that the more is the population or the nearer is the distance from a central city the higher is the competitiveness score is constructed. According to the premises 5-factor scores and composite score are calculated by means of regression method, and the scores are regressed on cities' populations and distances from Seoul city. Using bootstrapping method for the tests of significance is effective due to small sample of 21 cities. Results of the analyses show that most aspects of the hypothesis should be rejected or adjusted. Scores on Health-welfare factor, public service factor, and commercial vitality factor have no relation to the cities' sizes or distances. But the results also find the facts that the strong (negative) relationships exist between (1) educational base factor score and population, (2) density factor score and distance. Although this study improves systematic and analytic understanding of spatial interaction patterns, the understanding should be invalid for the general context because it has used the data on 21 cities in the capital region at the time of 2009.

• Composites Research
• /
• v.13 no.3
• /
• pp.58-66
• /
• 2000

CARALL(Carbon fiber reinforced aluminum laminates) was fabricated with CFRP prepreg and A17075, using a autoclave. The mechanical properties of three samples i.e. A17075, CFRP and CARALL were also investigated as a function of size in circular holes. Theoretical approach into analysing mechanical behaviors near the circular hole notch was carried out to compare with experimental data, furthermore. By the adhesive bonding of A17075 to CFRP, abrupt strength reduction was prevented. From the consideration of modified point stress failure criterion, predicted results was well consistent with the experimental one.