• Steel and Composite Structures
• /
• 제25권4호
• /
• pp.505-521
• /
• 2017

The steel plate shear wall with beam-only connected infill plate (SSW-BO) is an innovative lateral load resisting system consisting of infill plates connected to surrounding beams and separated from the main columns. In this research, the effects of perforation diameter as well as slenderness ratios of infill plates on the hysteresis behavior of SSW-BO systems were studied experimentally. Experimental testing is performed on eight one-sixth scaled one-story SSW-BO specimens with two plate thicknesses and four different circular opening ratios at the center of the panels under fully reversed cyclic quasi-static loading in compliance with the SAC test protocol. Strength, stiffness, ductility and energy absorption were evaluated based on the hysteresis loops. It is found that the systems exhibited stable hysteretic behavior during testing until significant damage in the connection of infill plates to surrounding beams at large drifts. It is also seen that pinching occurred in the hysteresis loops, since the hinge type connections were used as boundaries at four corners of surrounding frames. The strength and initial stiffness degradation of the perforated specimens containing opening ratio of 0.36 compared to the solid one is in the range of 20% to 30% and 40% to 50%, respectively.

• 한국정밀공학회지
• /
• 제30권4호
• /
• pp.434-441
• /
• 2013

Bending motion has been used in the surgical instruments with bending structures and tendon mechanisms. A simplified bending angle amplification ratio between the proximal and distal bending joint was derived in this article. The bending structure of disk and rib in the proximal joint was analyzed based on finite element method with an emphasis on the circumferential uniformity of bending stiffness. Regarding the distal joint, optimal design and sensitivity analysis was done with four design variables of outer and inner diameter, rib height and rib width while maximizing the deformation under the stress distribution below the yield stress. Outer diameter and rib width are most critical to maximum deformation as the outer diameter and inner diameters are so to maximum equivalent stress.

• 지역사회간호학회지
• /
• 제17권2호
• /
• pp.283-294
• /
• 2006

Purpose: The purpose of this study was to identify the factors influencing childhood immunization. Method: Data were collected by questionnaires from 251 Parents who have 6 months to 7 years old children at public health centers in Seoul and Kyunggi Province. The data were analyzed using descriptive statistics, t-test, ANOVA, and multiple regression. Result: According to general characteristics of the parents and children, there were statistically significant differences in education level of parents, child immunization card, gender, age, and birth order of children. The main factors that affected children's immunization were perceived barriers of action, perceived control, birth order of children, child immunization card, and education level of parents, and these factors explained 49.4%(explanatory power of this model was 49.4%). Conclusion: The results of this study showed strategies for compliance of children immunization. Therefore, when the program are developed for public immunization, these factors need to be considered.

• Asian Pacific Journal of Cancer Prevention
• /
• 제17권4호
• /
• pp.1933-1936
• /
• 2016

Heavy metals are known to disrupt important physiological processes in living cells, and have been responsible for various pathological conditions with possible contributions to cancer development. Food contamination have been identified as one of the ways humans are exposed to heavy metals. In developing countries like Nigeria, the regulatory framework for enforcing compliance with globally acceptable exposure to deleterious contaminants is poor. In the current study, thirteen samples of cured meat products of diverse origin marketed in South-west Nigeria were evaluated for lead, cadmium, chromium and nickel contents using the atomic absorption spectroscopy technique. All the samples analysed contained cadmium between 0.35 and 1.20 ppm, levels considered higher than acceptable limits in consumable products. Lead, chromium and nickel were not detected in any of the samples. As known cumulative poisons, there is the need for stringent regulatory control of these heavy metals in cured meat products imported into or produced indigenously in the country in order to minimize the risks to public health.

• 성인간호학회지
• /
• 제14권4호
• /
• pp.581-590
• /
• 2002

Purpose: The purpose of this correlational study was to identify relationships among job stress, health beliefs and health behaviors of aircrews and contributing factors to aircrew's health promoting behaviors. Method: Two-hundred twenty-four aircrew members completed questionnaires. The questionnaires were composed of a demographic form, health behavior scale, self-efficacy scale, perceived benefit scale, perceived barrier scale, job demand scale, and latitude scale. Result: The subject's health behavior has shown significant correlations with self-efficacy, benefit, and barrier. Significant negative correlations were found between job stress and self-efficacy. Relationships between job stress and barriers were also statistically significant. In demographic features, statistically significant difference were found between subject's rank and job stress score. Also, there was a significant difference between health behavior and the subject's age. Conclusion: Future efforts should focus on the development of a program to consider aircrew's perceived benefits, perceived barriers and self-efficacy to the compliance of health promoting behaviors.

• Asian Pacific Journal of Cancer Prevention
• /
• 제14권2호
• /
• pp.769-773
• /
• 2013

Background: A literature review on 1,104,269 cancer patients concluded that the prevalence of multiple primary malignancies (MPM) is between 0.73% and 11.7%. MPMs seem to have higher incidence than that influenced by hazard only. The purpose of this study was to investigate clinically useful information for effective screening for synchronous and metachronous second primary cancers and to identify a potential surveillance protocol. Materials and Methods: Using statistical and epidemiological indicators we evaluated the patients with MPMs (double locations) admitted to Dr. Abdurrahman Yurtarslan Ankara Oncology Education and Research Hospital between 1981 and 2010. Results: Out of the 130 cases, 24 (18.4%) were synchronous while 106 cases (81.6%) were metachronous tumours. Mean interval time from first to second primary cancers was 4.65 years (0-27 years). The most frequent malignant associations were breast-breast, breast-endometrium and breast-ovary. Both primary and secondary tumors tended to be in an advanced stage explained by the low compliance of the patients to follow-up. Conclusions: The possibility that MPMs exist must always be considered during pretreatment evaluation. Screening procedures are especially useful for the early detection of associated tumors, whereas careful monitoring of patients treated for primary cancer and a good communication between patients and medical care teams should ensure early detection of secondary tumors, and subsequent appropriate management.

• 한국소음진동공학회논문집
• /
• 제17권10호
• /
• pp.958-966
• /
• 2007

This study presents full vehicle dynamics model for the dynamic characteristic analysis of chassis parts which are suspension and brake system. This vehicle dynamics model is appled to kinematics and quasi-static analysis for each chassis part. In order to develop the vehicle dynamics model, the parameters of each chassis element part which are bush, spring and damper are measured by experiment. Also the wheel forces and moments of 6 DOF are measured at each wheel center. These data are applied to input parameter for vehicle dynamics model. And the verification of the developed model is achieved to comparison with the experimental force data of spring, trailing arm and assist arm by using the load response by strain gauge. These experimental force data are acquired by road test at event surfaces of P/G which are belgian and chuck holes roads.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제11권2호
• /
• pp.970-979
• /
• 2019

Compliant Vertical Access Risers (CVARs) are compliant systems that incorporate a differentiated geometric configuration that allows the exploitation of oil and gas in deepwater fields and enables a number of operational advantages in the offshore system. One of the main features of CVAR systems is that they allow direct intervention procedures to be applied to the well bore, enabling workover operations to be performed directly from the production platform. Based on the principles of virtual work and variation, a static geometric nonlinear equation of CVARs is derived and applied in this study. The results of this study show that the two ends of the riser as well as the transition region are subject to high stress, while the positions of the floating platform exert significant effects on the geometry of the riser configuration. Compliance and buoyancy factors should be set moderately to reduce the CVAR stress. In addition, the buoyancy modules should be placed in the lower region, in order to maximize the operation advantages of CVAR.

• 한국지진공학회논문집
• /
• 제22권1호
• /
• pp.23-32
• /
• 2018

In this study, we conducted a shake table test to verify the seismic performance of the paneling system with steel truss composed of bolt connections. The control group was set to the traditional paneling system with steel truss connected by spot welding method. Test results showed that the bolted connection type paneling system has excellent deformation capacity without cracking or brittle fracture of the steel truss connection parts compared to the welding type paneling system. Furthermore, in the bolted connection type, slight damage occurred at the time of occurrence of the same story drift angle as compared with the existing method, it is considered that it has excellent seismic performance. In compliance with the performance-based design recommended for the current code (ASCE 41-13) on non-structural components, it is judged that in the case of the bolted connection type paneling system, it can be applied to all risk category structures without restriction. However, in the case of traditional paneling system with spot welding method, it is considered that it can be applied limitedly.

• 한국유체기계학회 논문집
• /
• 제20권2호
• /
• pp.63-68
• /
• 2017

This paper predicts the rotordynamic force coefficients of tilting pad journal bearings (TPJBs) with ball-socket pivot and compares the predictions to the published test data obtained under load-between-pad (LBP) configuration. The present TPJB model considers the pivot stiffness calculated based on the Hertzian contact stress theory. Due to the compliance of the pivot, the predicted journal eccentricity agree well with the measured journal center trajectory for increasing static loads, while the early prediction without pivot model consideration underestimates it largely. The predicted pressure profile shows the significant pressure development even on the unloaded pads along the direction opposite to the loading direction. The predicted stiffness coefficients increase as the static load and the rotor speed increase. They agree excellently with test data from open literature. The predicted damping coefficients increase as the static load increases and the rotor speed decreases. The prediction underestimates the test data slightly. In general, the current predictive model including the pivot stiffness improves the accuracy of the rotordynamic performance predictions when compared to the previously published predictions.