• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.2
• /
• pp.199-208
• /
• 2012

This paper proposes a quasi Z-source DVR(Dynamic Voltage Restorer) system with a series connection of the output terminals, to compensate the voltage variations in the 6.6[kV]/60[Hz] power distribution system. The conventional DVR using one quasi Z-source AC-AC converter has the advantage which it can compensate the voltage variations without the need for the additional energy storage device such as a battery, but it is impossible to compensate for the 50[%] under voltage sags. To solve this problem, a DVR system using two quasi Z-source AC-AC converters with the series connection of the output terminals is proposed. By controlling the duty ratio D in the buck-boost mode, the proposed system can control the compensation voltage. For case verification of the proposed system, PSIM simulation is achieved. As a result, in case that the voltage sags-swells occur 10[%], 20[%], 60[%] in power distribution system, and, in case that the 50[%] under voltage sags-swells continuously occur, all case could compensate by the proposed system. Especially, the compensated voltage THD was examined under the condition of the 10[%]~50[%] voltage sags and the 20[${\Omega}$]~100[${\Omega}$] load changes. The compensated voltage THD was worse for the higher load resistances and more severe voltage sags. Finally, In case of the voltage swells compensation, the compensation factor has approached nearly 1 regardless of the load resistance changes, while the compensation factor of voltage sags was related to the load variations.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.37 no.5
• /
• pp.42-53
• /
• 2000

Efficient implementation of pre-filtering has been an important issue in video sequence coding, because it can remove camera noise and improve coding efficiency dramatically This paper introduces a novel pre-filtering scheme that is performed inside a video encoder The proposed pre-filtering is based on the approximated generalized Wiener filtering and two-dimensional discrete cosine transform (DCT) factorization. and is achieved by scaling the DCT coefficients of original image blocks for intra block coding and those of motion-compensated error blocks for inter block coding, respectively Even though the pre-filtering operation is embedded in a video encoder, its additional computational complexity is marginal compared to the encoding process, and the overall architecture of the conventional video encoder is maintained In spite of its simplicity, the proposed pre-filtering scheme provides good filtering and coding performance for noisy video sequences.

• Journal of Broadcast Engineering
• /
• v.20 no.2
• /
• pp.265-272
• /
• 2015

A new technology on video frame rate up-conversion (FRUC) is presented by combining the median filter and motion estimation (ME) with an occlusion detection (OD) method. First, ME is performed to have a motion vector. Then, the OD method is used to refine motion vector in the occlusion region. Since the wrong motion vector can be obtained with high possibility in the occluded area, a median filtering that less depends on the motion vector is applied to that area, and since the motion vector is continuous and robust in the non-occluded area, BDMC(Bi-Directional Motion Compensated interpolation) is applied to obtain interpolated image in that area. BDMC using the bi-directional motion vectors achieves good results when continuity and robustness of the motion vector is higher. Experimental results show that the proposed algorithm provides better performance than the conventional approach. The average gain of PSNR (Peak Signal to Noise Ratio) is approximately 0.16 dB in the test sequences compared with BDMC.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.43 no.5 s.311
• /
• pp.28-35
• /
• 2006

This paper presents a new 3.3-1 V synchronous buck DC/DC converter that employs CMOS operational transconductance amplifiers (OTAs) as circuit-building blocks. An error amplifier OTA in a PWM circuit is compensated for to improve temperature stability. The temperature coefficient of the transconductance gain of the compensated OTA is less than $150\;ppm/^{\circ}C\;over\;0-100^{\circ}C$. The HSPICE simulation results of the $0.3{\mu}m$ standard CMOS technology show that the efficiency of the proposed converter is as high as 80% in the load current range of 40-125 mA. These results show that the proposed converter is adequate for use in battery-operated systems.

• Korean Journal of Computational Design and Engineering
• /
• v.9 no.4
• /
• pp.397-405
• /
• 2004

Texture mapping is the process of covering 3D models with texture images in order to increase the visual realism of the models. For proper mapping the coordinates of texture images need to coincide with those of the 3D models. When projective images from the camera are used as texture images, the texture image coordinates are defined by a camera calibration method. The texture image coordinates are determined by the relation between the coordinate systems of the camera image and the 3D object. With the projective camera images, the distortion effect caused by the camera lenses should be compensated in order to get accurate texture coordinates. The distortion effect problem has been dealt with iterative methods, where the camera calibration coefficients are computed first without considering the distortion effect and then modified properly. The methods not only cause to change the position of the camera perspective line in the image plane, but also require more control points. In this paper, a new iterative method is suggested for reducing the error by fixing the principal points in the image plane. The method considers the image distortion effect independently and fixes the values of correction coefficients, with which the distortion coefficients can be computed with fewer control points. It is shown that the camera distortion effects are compensated with fewer numbers of control points than the previous methods and the projective texture mapping results in more realistic image.

• Journal of Broadcast Engineering
• /
• v.16 no.6
• /
• pp.1058-1068
• /
• 2011

Video FRUC (Frame Rate Up Conversion) is one of the main issues that have arisen in recent years with the explosive growth of video sources and display formats in consumer electronics. Most advanced FRUC algorithms adopt an efficient motion interpolation technique to determine the motion vector field of interpolated frames. But, in some application areas such as post processing in receiver side, it is necessary to evaluate how well the MCI (Motion Compensated Interpolation) frame was reconstructed. In order to achieve this aim, first, this paper introduces some cost functions to estimate the reliability of a block in the MCI frame. Then, by using these functions, this paper proposes two distortion estimation models for evaluating how much noise was produced in the MCI frame. Through computer simulations, it is shown that the proposed estimation methods perform effectively in estimating the noises of the MCI frame.

• Journal of Broadcast Engineering
• /
• v.18 no.3
• /
• pp.342-348
• /
• 2013

In this paper, a novel frame rate up conversion (FRUC) algorithm using adaptive extended bilateral motion estimation (AEBME) is proposed. Conventionally, extended bilateral motion estimation (EBME) conducts dual motion estimation (ME) processes on the same region, therefore involves high complexity. However, in this proposed scheme, a novel block type matching procedure is suggested to accelerate the ME procedure. We calculate the edge information using sobel mask, and the calculated edge information is used in block type matching procedure. Based on the block type matching, decision will be made whether to use EBME. Motion vector smoothing (MVS) is adopted to detect outliers and correct outliers in the motion vector field. Finally, overlapped block motion compensation (OBMC) and motion compensated frame interpolation (MCFI) are adopted to interpolate the intermediate frame in which OBMC is employed adaptively based on frame motion activity. Experimental results show that this proposed algorithm has outstanding performance and fast computation comparing with EBME.

• Transactions of Materials Processing
• /
• v.20 no.3
• /
• pp.229-235
• /
• 2011

The formability of magnesium alloy sheets at room temperature is generally low because of the inherently limited number of slip systems, but higher at temperatures over $150^{\circ}C$. Therefore, prior to the practical application of these materials, the forming limits should be evaluated as a function of the temperature and strain rate. This can be achieved experimentally by performing a series of tests or analytically by deriving the corresponding modeling approaches. However, before the formability analysis can be conducted, a model of flow stress, which includes the effects of strain, strain rate and temperature, should be carefully identified. In this paper, such procedure is carried out for Mg alloy AZ31 and the concept of flow stress surface is proposed. Experimental flow stresses at four temperature levels ($150^{\circ}C$, $200^{\circ}C$, $250^{\circ}C$, $300^{\circ}C$) each with the pre-assigned strain rate levels of $0.01s^{-1}$, $0.1s^{-1}$ and $1.0s^{-1}$ are collected in order to establish the relationships between these variables. The temperature-compensated strain rate parameter which combines, in a single variable, the effects of temperature and strain rate, is introduced to capture these relationships in a compact manner. This study shows that the proposed concept of flow stress surface is practically relevant for the evaluation of temperature and strain dependent formability.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.7
• /
• pp.532-539
• /
• 2018

A position estimation technique is presented for a missile using high-resolution range profiles obtained by three wideband radars. Radar measures a target range using a reflected signal from the surface of a missile. However, it is difficult to obtain the range between the radar and the origin of the missile. For this reason, the interior angle between the moving missile and tracking radar is calculated, and a compensated range between surface of the missile and its origin is added to the tracking range of the radar. Therefore, position estimation of a missile can be achieved by using three total ranges from each radar to the origin of the missile. To verify the position estimation of the missile, electromagnetic numerical analysis software was used to prove the compensated range according to the flight position. Moreover, a wideband radar operating at 500-MHz bandwidth was applied, and its range profile was used for the position estimation of a missile.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.9 no.5
• /
• pp.458-464
• /
• 2016

This paper proposes the compensation method which decreases the radiation pattern distortion caused by the mutual coupling in an array antenna. If the element distance of an array antenna decreases, the radiation pattern could be distorted by the strong mutual coupling, which changes the magnitude and phase of input signals and causes an unwanted radiation pattern. To remove the pattern distortion, compensated input signals are inserted in an array antenna. The magnitude and phase of input signals are determined by Particle Swarm Optimization (PSO) algorithm. A $4{\times}1$ dipole array antenna with omnidirectional elements is used to confirm the validity of the algorithm, where each element is placed in 0.2 wavelength to evoke the strong coupling. After input signals are optimized by PSO, it is found that the compensated radiation results in the same as the ideal case.