• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.16 no.4
• /
• pp.89-96
• /
• 2016

In this paper, we study mobile data collector (MDC) based data-gathering schemes in wireless sensor networks. In Such networks, MDCs are used to collect data from the environment and transfer them to the sink. The majority of existing data-gathering schemes suffer from high data-gathering latency because they use only a single MDC. Although some schemes use multiple MDCs, they focus on maximizing network lifetime rather than minimizing packet delay. In order to address the limitations of existing schemes, this paper focuses on minimizing packet delay for given number of MDCs and minimizing the number of MDCs for a given delay bound of packets. To achieve the minimum packet delay and minimum number of MDCs, two optimization problems are formulated, and traveling distance and traveling time of MDCs are estimated. The interior-point algorithm is used to obtain the optimal solution for each optimization problem. Numerical results and analysis are presented to validate the proposed method.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.47 no.3
• /
• pp.1-4
• /
• 2010

RS-485, communication bases from small network system must prepare in collision. The collision is that mean the data transfer breaks. For a stabilized communication chooses 1:N polling methods. But polling is low speed in addition to maybe overload Master device. So, usual N:N Prefers a communication. In this case, must be preparing to avoid collision or some solutions. Generally, to after collision retransmits after short time. It's called delay time for short time. When making a delay time, uses address of each systems. (Address of each node) If the many nodes collided, the each node has different delay time. When making a delay time, uses a usual random number. Making a random number is hard job. So uses a usual pseudorandom number. It is more difficult from small size MCU. The Chaos random number provides stabled value. Finally, when uses the Chaos random number, the stability and reliability of system get better.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.657-659
• /
• 2004

CAN is a serial communication bus for real-time controls and automations in distributed control systems. In distributed control systems, occasionally a sensor module and a controller are not in the same node and physically separated. In order for the signal from a sensor node to reach the controller node, the signal must travel through network. CAN has a certain capabilities to deal with real-time data. However, when many nodes on the networks try to send data on the same network, the arbitration mechanism to solve the data collision problem is necessary. This situation causes the time delay which has detrimental effects on the performance of the control systems. This paper proposes a method to solve the problem due to the time delay in distributed control system using CAN. Time delay is approximated to an element with a rational transfer function using Pade approximation and Mu~synthesis method is applied. Since time delay in the network is not constant, the time delay element is considered to be an uncertainty block with a bound. The proposed method is applied to the experimental system with CAN and proved to be effective.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.11
• /
• pp.1481-1489
• /
• 2016

A art from the typical data services based on 1:1 data communications, various new services based on 1:N communications have recently appeared. These services are becoming to require advanced 1:N communication schemes which can transfer the same data to many receivers efficiently and in high-performance. Especially, a Push-To-Talk (PTT) service, which is an important service in public safety communication system, requires a service server to disseminate the same voice media data to multiple receivers in a group in real-time and low latency. In this paper, we propose an efficient scheme to disseminate the same data to multiple receivers in low latency. In addition, we provide an analysis which gives a guide the performance of the 1:N communications in practical wired/wireless system environments in the perspective of the PTT service index.

• Proceedings of the KIEE Conference
• /
• 2008.11a
• /
• pp.379-381
• /
• 2008

TETRA(Terrestrial Trunked Radio) is a digital trunked radio standard developed by the ETSI(European Telecommunications Standards Institute). Currently, TETRA was set Digital TRS in electric power If wireless backbone network. In this time, we use many company's TETRA modem. So, TETRA modem performance evaluation is very important. TETRA modem use two type of Data transfer mode. One is Packet Data using UDP/IP. and the other is SDS(Short Data Service). In this paper, We generate Packet Data using Traffic Generator module. Packet Data transfer 1000 times each 10 bytes to 400 bytes. We analyze transmission delay time, success rate and standard deviation.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.2
• /
• pp.181-188
• /
• 2012

In this paper, the measurement data is analyzed and channel parameters are derived through MIMO Channel measurements at 781MHz considering outdoor multi-path environment. 781MHz frequency band currently operates the DTV system. However, it will be allocated new mobile communication frequency band. The channel characteristics at 781MHz seem to be similar existing mobile communication system at 900MHz but a study on channel characteristics of signal transfer process is necessary because there is incomplete study in mobile networks at 781MHz. To avoid interference with Korean DTV broadcasting, we measured channel characteristics in city/suburban areas of Jeju island by channel sounder and $4{\times}4$ antenna of the ETRI(Korea Electronics and Telecommunications Research Institute). Path Loss, Delay Spread, Angular Spread and K-factor were derived based on measured data.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.11
• /
• pp.1269-1274
• /
• 2010

Wireless communication channels with the most severe multipath fading phenomenon that appears each time a different delay is caused by the frequency selective fading. At this time, ISI due to the performance degradation of wireless communication channels and data transfer speed gives the constraints. OFDM technique can remove ISI inserting longer guard interval than channel delay spread of channel between symbol. However, the multi-path delay of the channel to be serious with the guard interval can not eliminate ISI. In this case, using the equalizer must compensate. Especially, use of equalizer is need absolutely as data rate becomes high speed. In this paper, we analyze the BER performance with pre-equalization for MIMO-OFDM over fading channel. The results of this paper can be applied to MIMO-OFDM system with equalization.

• Journal of applied mathematics & informatics
• /
• v.12 no.1_2
• /
• pp.395-408
• /
• 2003

Common Channel Signaling(CCS) networks need special controls to avoid overload of signaling networks and degradation of call process-ing rate, since they play an important role of controlling communication transfer networks. Congestion control and flow control mechanisms are well described in ITU-T recommendation on Signaling System No.7(SS7). For the practical provisions, however, we need an analysis on the relation among service objects, system requirements and implementation of congestion control algorithms. SS7 provides several options for controlling link congestion in CCS networks. In this paper we give a general queueing model of congestion control algorithm which covers both the international and national options. From the queuing model, we obtain the performance parameters such as throughput, message loss rate and mean delay for the international option. To show the performance of the algorithm, some numerical results are also given.

• International Journal of Computer Science & Network Security
• /
• v.23 no.9
• /
• pp.8-16
• /
• 2023

In Japan, high-speed ground transportation service using linear motors at speeds of 500 km/h is scheduled to begin in 2027. To accommodate 5G services in trains, a subcarrier spacing frequency of 30 kHz will be used instead of the typical 15 kHz subcarrier spacing to mitigate Doppler effects in such high-speed transport. Furthermore, to increase the cell size of the 5G mobile system, multiple base station antennas will transmit identical downlink (DL) signals to form an expanded cell size along the train rails. In this situation, the forward and backward antenna signals are Doppler-shifted in opposite directions, respectively, so the receiver in the train may suffer from estimating the exact Channel Transfer Function (CTF) for demodulation. In a previously published paper, we proposed a channel estimator based on Delay and Doppler Profiler (DDP) in a 5G SISO (Single Input Single Output) environment and successfully implemented it in a signal processing simulation system. In this paper, we extend it to 2×2 MIMO (Multiple Input Multiple Output) with spatial multiplexing environment and confirm that the delay and DDP based channel estimator is also effective in 2×2 MIMO environment. Its simulation performance is compared with that of a conventional time-domain linear interpolation estimator. The simulation results show that in a 2×2 MIMO environment, the conventional channel estimator can barely achieve QPSK modulation at speeds below 100 km/h and has poor CNR performance versus SISO. The performance degradation of CNR against DDP SISO is only 6dB to 7dB. And even under severe channel conditions such as 500km/h and 8-path inverse Doppler shift environment, the error rate can be reduced by combining the error with LDPC to reduce the error rate and improve the performance in 2×2 MIMO. QPSK modulation scheme in 2×2 MIMO can be used under severe channel conditions such as 500 km/h and 8-path inverse Doppler shift environment.

• Journal of Korea Multimedia Society
• /
• v.18 no.4
• /
• pp.506-523
• /
• 2015

The intent is to determine whether or not the custody transfer is helpful for data transmission in challenging underwater communications when running Bundle protocol or underwater protocols. From the point of view defending side, Underwater Acoustic Network (UAN) will be a serious threat for its strong functionality long rang and high precision of surveillance and detection. Therefore, countermeasures must be taken to weaken its effect. Our purpose is analyzed that how to benefit from the UIoT to learn from, exploit and preserve the natural underwater resources. Delay/Disruption Tolerant Network (DTN) is essential part of the network heterogeneity communication network. The vulnerability and potential security factors of UIoT are studied thereafter. Security mechanisms for an underwater environment are difficult to apply owing to the limited bandwidth. Therefore, for underwater security, appropriate security mechanisms and security requirements must be defined simultaneously. The paper consists of mathematical and security model. Most important point of view in the security challenges of effective Buffer and Storage management in DTN.