• Structural Engineering and Mechanics
• /
• 제22권2호
• /
• pp.169-184
• /
• 2006

A close form solution of the maximum deflection for cracked columns with rectangular cross-sections was developed and thus the elastic buckling behavior and ultimate bearing capacity were studied analytically. First, taking into account the effect of the crack in the potential energy of elastic systems, a trigonometric series solution for the elastic deflection equation of an arbitrary crack position was derived by use of the Rayleigh-Ritz energy method and an analytical expression of the maximum deflection was obtained. By comparison with the rotational spring model (Okamura et al. 1969) and the equivalent stiffness method (Sinha et al. 2002), the advantages of the present solution are that there are few assumed conditions and the effect of axial compression on crack closure was considered. Second, based on the above solutions, the equilibrium paths of the elastic buckling were analytically described for cracked columns subjected to both axial and eccentric compressive load. Finally, as examples, the influence of crack depth, load eccentricity and column slenderness on the elastic buckling behavior was investigated in the case of a rectangular column with a single-edge crack. The relationship of the load capacity of the column with respect to crack depth and eccentricity or slenderness was also illustrated. The analytical and numerical results from the examples show that there are three kinds of collapse mechanisms for the various states of cracking, eccentricity and slenderness. These are the bifurcation for axial compression, the limit point instability for the condition of the deeper crack and lighter eccentricity and the fracture for higher eccentricity. As a result, the conception of critical transition eccentricity $(e/h)_c$, from limit-point buckling to fracture failure, was proposed and the critical values of $(e/h)_c$ were numerically determined for various eccentricities, crack depths and slenderness.

• 한국전산구조공학회논문집
• /
• 제19권4호
• /
• pp.375-387
• /
• 2006

기존의 연구에서 가정된 모멘트-곡률 관계를 토대로 고정된 안정계수를 갖는 응답스펙트럼을 구성하여 동적 P-$\Delta$ 효과를 분석한 것과는 달리, 이 논문에서는 안정계수의 증가, 즉, 축력의 증가에 따른 하중-변위관계의 변화를 고려할 수 있도록하는 적층단면법을 토대로 실용범위의 세장비와 안정계수를 변화시켜가며, 해석을 수행하여 철근콘크리트 장주의 동적 P-$\Delta$ 효과를 분석하였다. 다양한 지진에 대한 보편화된 결과를 얻기 위해 각기 다른 60개의 입력지진을 사용하였다. 또한, 수평지진과 수직지진을 동시에 작용하여 해석을 수행해 수직지진에 따른 P-$\Delta$ 효과를 살펴보았다. 해석결과, 철근콘크리트 장주의 최대변형은 축력, P-$\Delta$ 효과 및 수직지진의 영향을 거의 받지 않는 반면, 부재 내력은 축력에 의한 강성과 항복강도의 증가에 의해 증가하기 때문에, 철근콘크리트 장주의 내진설계시 축력효과를 고려하여 설계할 경우 P-$\Delta$ 효과 또는 수직지진에 대한 추가적인 영향은 고려하지 않아도 될 것으로 판단된다.

• 한국수정란이식학회지
• /
• 제13권3호
• /
• pp.301-312
• /
• 1998

난포액내 함유되어 있는 단백질성분 중에서 sucrose 층으로부터 정자의 swim-up 이동을 자 극하는 성분을 분리하기 위하여 paper chromatography (PC) 및 reverse phase column (RPC) 과 superose column (SC)를 이용한 액체 chromatography의 분리효과를 조사하였던 바 결과는 다음과 같다. 1. Chromatography용 paper로 분리한 각 band 의 성분은 첨가농도가 증가할수록 정자의 이동과 운동을 자극하였으며, 특히 band 1 성분은 정자의 이동을 유의하게 증가시켰다. 그러나, 동일 첨가수준에서 bands 성분의 정자 이동과 운동자극효과는 난포액의 효과에 비하여 유의하게 낮았다. 2. $\mu$RPC를 이용 2~5mm 난포로 부터 분리한 성분중 RT3.33, RT7.00, RTl3.87 및 RTl6.6A 성분은 정자의 이동을 자극하였으나, 자극효과는 매우 적었다. 3. $\mu$RPC를 이용 10mm 난포로 부터 분리한 성분은 정자의 이동과 활력을 자극하지 않았다. 4. SC를 이용 2-5mm 난포로 부터 분리한 성분 중 RVI.35 성분과 RV0.82 성분은 정자의 이동과 운동을 유의하게 자극하였다. 결론적으로 난포액내 정자의 이동과 운동을 자극하는 단백질 성분은 superose column을 이용하여 효과적으로 분리할 수 있으며, 분리된 RVI.35 성분과 RV0.82 성분은 정자의 swim-up 분리를 자극하였다.

• International Journal of Concrete Structures and Materials
• /
• 제8권2호
• /
• pp.99-116
• /
• 2014

The American Concrete Institute (ACI) 318-11 permits the use of the moment magnifier method for computing the design ultimate strength of slender reinforced concrete columns that are part of braced frames. This computed strength is influenced by the column effective length factor K, the equivalent uniform bending moment diagram factor $C_m$ and the effective flexural stiffness EI among other factors. For this study, 2,960 simple braced frames subjected to short-term loads were simulated to investigate the effect of using different methods of calculating the effective length factor K when computing the strength of columns in these frames. The theoretically computed column ultimate strengths were compared to the ultimate strengths of the same columns computed from the ACI moment magnifier method using different combinations of equations for K and EI. This study shows that for computing the column ultimate strength, the current practice of using the Jackson-Moreland Alignment Chart is the most accurate method for determining the effective length factor. The study also shows that for computing the column ultimate strength, the accuracy of the moment magnifier method can be further improved by replacing the current ACI equation for EI with a nonlinear equation for EI that includes variables affecting the column stiffness and proposed in an earlier investigation.

• Steel and Composite Structures
• /
• 제36권4호
• /
• pp.427-446
• /
• 2020

This paper carries out the progressive collapse analysis of stainless steel composite beam-to-column joint sub-models and moment-resisting frames under column removal scenarios. The static flexural response of composite joint sub-models with damaged columns was initially explored via finite element methods, which was validated by independent experimental results and discussed in terms of moment-rotation relationships, plastic hinge behaviour and catenary actions. Simplified finite element methods were then proposed and applied to the frame analysis which aimed to elaborate the progressive collapse response at the frame level. Nonlinear static and dynamic analysis were employed to evaluate the dynamic increase factor (DIF) for stainless steel composite frames. The results suggest that the catenary action effect plays an important role in preventing the damaged structure from dramatic collapse. The beam-to-column joints could be critical components that influence the capacity of composite frames and dominate the determination of dynamic increase factor. The current design guidance is non-conservative to provide proper DIF for stainless steel composite frames, and thus new DIF curves are expected to be proposed.

• 한국환경농학회지
• /
• 제16권2호
• /
• pp.115-118
• /
• 1997

When the light metals such as $Ca^{++}$ and $Mg^{++}$ were added to heavy metal solution, the adsorption of heavy metals was increased by 20 to 30% more, but there were no differences between species. $Pb^{++}$ was the most adsorbed metal(99.5%), and the adsorption ratio of $Cd^{++}$ was significantly improved. In addition, when the light metal concentration was increased to 100ppm, the adsoption ratios of all four heavy metals were reached to 92 to 99%, while coniferous barks showed only 85 to 92%. On the mixture of four heavy metals, the adsorbed amount of each metal was significantly reduced, compared with that of one heavy metal, while $Zn^{++}$ showed the adsorption improvement to 95%. On the column experiment, $Pb^{++}$ was almost completely adsorbed in the upper part of column, and the adsorbed amount of $Cu^{++}$ was gradually decreased depending on column depth. However, $Cd^{++}$ and $Zn^{++}$ were not influenced by column height, and constantly adsorbed on various column height. Based on the above results, each heavy metal had different adsorption mechanism.

• Structural Engineering and Mechanics
• /
• 제21권1호
• /
• pp.35-52
• /
• 2005

This paper proposes a realistic approach to pushover analyses of reinforced concrete (RC) structures with single column type and frame type. The characteristic of plastic hinge of a single RC column subjected to fixed axial load was determined first according to column's three distinct failure modes which were often observed in the experiments or earthquakes. By using the determined characteristic of plastic hinge, the pushover analyses of single RC columns were performed and the analytical results were investigated to be significantly consistent with those of cyclic loading tests. Furthermore, a simplified methodology considering the effect of the variation of axial force for each RC column of the frame structure during pushover process is proposed for the first time. It would be helpful in performing pushover analysis for the structures examined in this study with efficiency as well as accuracy.

• Wind and Structures
• /
• 제24권5호
• /
• pp.431-446
• /
• 2017

As concrete is most usable material in construction industry it's been required to improve its quality. Nowadays, nanotechnology offers the possibility of great advances in construction. In this study, buckling of horizontal concrete columns reinforced with Zinc Oxide (ZnO) nanoparticles is analyzed. Due to the presence of ZnO nanoparticles which have piezoelectric properties, the structure is subjected to electric field for intelligent control. The Column is located in foundation with vertical springs and shear modulus constants. Sinusoidal shear deformation beam theory (SSDBT) is applied to model the structure mathematically. Micro-electro-mechanic model is utilized for obtaining the equivalent properties of system. Using the nonlinear stress-strain relation, energy method and Hamilton's principal, the motion equations are derived. The buckling load of the column is calculated by Difference quadrature method (DQM). The aim of this study is presenting a mathematical model to obtain the buckling load of structure as well as investigating the effect of nanotechnology and electric filed on the buckling behavior of structure. The results indicate that the negative external voltage applied to the structure, increases the stiffness and the buckling load of column. In addition, reinforcing the structure by ZnO nanoparticles, the buckling load of column is increased.

• Architectural research
• /
• 제2권1호
• /
• pp.55-60
• /
• 2000

Recently, there is a great demand for precast reinforced concrete (RC) construction methods on the purpose of simplicity in construction. Nishimatsu Construction Company has developed a construction method with precast reinforced concrete members in medium-rise building. In this construction method, how to joint precast members, especially the anchorage of the main bar of beam, is important problem. In this study, the structural performance of exterior joints with precast members was investigated. The parameters of the test specimens are anchorage type of the main bar of beam (U-shape anchorage or anchorage plate) and the ratio of the column axial force to the column strength. Specimens J-3 and J-4 used U-shape anchorage and the ratio of the column axial force of specimen J-4 was higher. On the other hand, specimens J-5 and J-6 used anchorage plate, and the anchorage lengths are 15d and 18d, respectively. Experimental results are summarized as follows; 1) For the joints with beam flexural failure mode, it was found that the maximum strength of specimen with anchorage plate is equal to or larger than that of specimen with conventional U-shaped anchorage if the anchorage length of more than 15d would be ensured, 2) Each specimen shows stable hysteretic curves and there were no notable effects on the hysteretic characteristics and the maximum strength caused by the anchorage method of beam main bar and the difference of column axial stress level.

• Environmental Engineering Research
• /
• 제19권1호
• /
• pp.107-113
• /
• 2014

Small sized manganese dioxide particles are immobilized onto the surface of sand by the wet impregnation process. The surface morphology of the solid, i.e., immobilized manganese dioxide natural sand (IMNS) is performed by taking scanning electron microscope images and characterized by the X-ray diffraction data. The specific surface area of the solid is obtained, which shows a significant increase in the specific surface area obtained by the immobilization of manganese dioxide. The $pH_{PZC}$ (point of zero charge) is found to be 6.28. Further, the IMNS is assessed in the removal of As(III) and As(V) pollutants from aqueous solutions under the batch and column operations. Batch reactor experiments are conducted for various physicochemical parametric studies, viz. the effect of sorptive pH (pH 2.0-10.0), concentration (1.0-25.0 mg/L), and background electrolyte concentrations (0.0001-0.1 mol/L $NaNO_3$). Further, column experiments are conducted to obtain the efficiency of IMNS under dynamic conditions. The breakthrough data obtained by the column experiments are employed in non-linear fitting to the Thomas equation, so as to estimate the loading capacity of the column for As(III) and As(V).