• 대한기계학회논문집B
• /
• 제24권10호
• /
• pp.1285-1293
• /
• 2000

In port fuel injection system of SI engines, injected fuel is impinged onto the surface of intake valves and port-wall, and then formed the wall flow under the cold start operation. Wall flows entrained into the cylinder result in the unsteady and nonuniform mixture formation. Therefore, the spray impingement to the wall is considered as having negative influences such as lowering combustion efficiency and causing unburned hydrocarbon emissions. This study investigates the spray characteristics of the wall impinging air-assist spray in suction air flow. A PDPA was used to analyze the flow characteristics under the different conditions such as impingement angle and supplied air. Experimental data concerning the impinging sprays has been obtained in the vicinity of the wall. Measured droplets divided into the pre-impinging droplets which denote as the positive normal velocities and post-impinging droplets that describe as the negative normal velocities for the suction flow. Their velocities, size distributions and SMD are comparatively analyzed before and after the impingement.

• 한국자동차공학회논문집
• /
• 제13권5호
• /
• pp.112-120
• /
• 2005

The injector, which is used in a 4-valve gasoline engine, is required to be maintained the dual stream because of the design of dual intake port. In addition, the spray characteristics of fuel injector have strong influence on engine performance, exhaust emission, fuel consumption, and especially the cold start condition for the port injection. So, commercial gasoline injectors off different type were inspected. Those are 2 hole,4 hole, air shroud 4 hole, and air shroud 4 hole injector with separator. The spray behavior of dual stream was researched by the visualization system and PDPA system was employed to measure the droplet size. Atomization is one of the most important characteristic, so droplet size distributions and SMD are investigated. And the spray characteristics of each injector are also analyzed such as the spray tip penetration, spray angle, and separation angle.

• 한국가스학회지
• /
• 제18권6호
• /
• pp.7-13
• /
• 2014

국내 외에서 대기 오염에 대한 관심은 높은 편이며, 자동차 및 연료 연구자들은 깨끗한 (친환경 대체연료) 연료와 연료 품질에 맞춘 새로운 엔진 설계의 구성, 혁신적인 후처리 시스템 등의 접근을 통하여 차량의 배기가스 배출을 줄이려고 노력하고 있다. 이러한 연구는 다음과 같은 다양한 주요 이슈를 가져오게 된다. PM 배출량이 디젤과 가솔린 차량에 대해 규제해야 하는지 여부와 가솔린 및 LPG 차량이 PM 배출가스 규제에서 무시될 수 있는지 여부이다. 마지막으로 온실 가스 (C$CO_2$, $CH_4$, $N_2O$) 규제가 자동차 배출 규제를 포함하여 논의 것 등이다. 자동차의 온실 가스 및 배출가스(PM)는 환경오염, 건강 악영향 등의 원인으로 많은 문제점을 일으키게 된다. 본 논문에서는 자동차 저온 시동성 및 배출가스에 대해 LPG 연료의 영향을 논의하였다. 또한 본 논문은 시험 온도에 대한 배출가스 특성을 평가하였다. 이때의 시험온도는 시험모드 상의 온도와 국내 겨울철 최저온도를 기준으로 나누어서 실시하였다. 본 연구를 통해 시동성 및 배출가스, 온실가스 배출의 상관관계를 분석하고자 하였다.

• 한국수소및신에너지학회논문집
• /
• 제33권1호
• /
• pp.77-84
• /
• 2022

The experimental work has been carried out for the study of pyrolysis of oil samples used in industrial and utility boilers in Korea. For five oil samples, the characteristics of pyrolysis have been investigated with a thermogravimetric analyzer (TGA), and their kinetic parameters were obtained and compared each other. The rate order of pyrolysis rate for five oils were as follows: by-product fuel oil, pyrolysis oil, diesel, a heavy oil and refined oil. The pyrolysis of refined oil has been successfully described by the three step, first order reaction model while the single step reaction model has been used for other oils. For the reaction temperature over 550 K, the reactivity of refined oil was very poor compared with other oils.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제4권4호
• /
• pp.403-411
• /
• 2012

This study presents the nano-sized particle emission characteristics from a small turbocharged common rail diesel engine applicable to prime and auxiliary machines on marine vessels. The experiments were conducted under dynamic engine operating conditions, such as steady-state, cold start, and transient conditions. The particle number and size distributions were analyzed with a high resolution PM analyzer. The diesel oxidation catalyst (DOC) had an insignificant effect on the reduction in particle number, but particle number emissions were drastically reduced by 3 to 4 orders of magnitude downstream of the diesel particulate filter (DPF) at various steady conditions. Under high speed and load conditions, the particle filtering efficiency was decreased by the partial combustion of trapped particles inside the DPF because of the high exhaust temperature caused by the increased particle number concentration. Retarded fuel injection timing and higher EGR rates led to increased particle number emissions. As the temperature inside the DPF increased from $25^{\circ}C$ to $300^{\circ}C$, the peak particle number level was reduced by 70% compared to cold start conditions. High levels of nucleation mode particle generation were found in the deceleration phases during the transient tests.

• 한국분무공학회지
• /
• 제23권3호
• /
• pp.122-127
• /
• 2018

Recently, registrated passenger cars have increased and were close about seventy million at the end 2017 year in Korea. Among the passenger car using gasoline fuel make up forty six percentage of total registrated vehicles. In this study, investigation on real driving emission characteristics in the passenger car using gasoline fuel with various engine displacements were carried out. The real driving emission characteristics were measured and analyzed by using PEMS (Portable Emission Measurement System). PEMS was composed of gas analyzer, emission flow meter and sample conditioning system et al. Also, test six vehicles were selected to the gasoline passenger car with engine displacement from 1.6L to 3.7L. Two test routes with engine start of cold and hot conditions were applied to analyze the emission characteristics of RDE, respectively. The results show that the $CO_2$ emission have a increasing trend as the engine displacement and vehicle weight. Also, it is guessed that the $CO_2$ emission and vehicle weight were more correlated than the engine displacements. On the other hand, NOx emissions of RDE have not increasing or decreasing tendency according engine displacements or vehicle weight because the activation of three-way catalyst in the gasoline vehicles.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권1호
• /
• pp.57-65
• /
• 2008

The characteristics of soot deposition on the cold wall in laminar diffusion flames have been numerically analyzed with a two-dimension with the FDS (Fire Dynamics Simulator). In particular, the effects of surrounding air temperature and wall temperature have been discussed. The fuel for the flame is an ethylene ($C_2H_4$). The surrounding oxygen concentration is 35%. Surrounding air temperatures are 300K, 600K, 900K and 1200K. Wall temperatures are 300K, 600K and 1200K. The soot deposition length defined as the relative approach distance to the wall per a given axial distance is newly introduced as a parameter to evaluate the soot deposition tendency on the wall. The result shows that soot deposition length is increased with increasing the surrounding air temperatures and with decreasing the wall temperature. And the numerical results led to the conclusion that it is essential to consider the thermophoretic effect for understanding the soot deposition on the cold wall properly.

• 한국추진공학회지
• /
• 제14권6호
• /
• pp.9-16
• /
• 2010

고체연료 램제트 추진의 경우 간단한 구조에 비해 높은 성능과 추진력을 얻을 수 있는 매력적인 추진기관이다. 본 연구의 목적은 두가지 유형의(스파이크 & 피토) 흡입구에 대한 공기역학적 특성을 파악함에 있다. 마하수 3.0의 실험조건에서 연소실의 압력과 $0^{\circ}$와 $4^{\circ}$의 받음각의 변화에 따라 흡입구 벽면의 압력값을 측정하였다. 본 연구는 초음속 유동장치와 쉴리렌 시스템을 이용하여 수행되었으며 동일 실험조건에서 스파이크 형이 피토 형보다 약 2배 높은 전압력 회복율을 나타내었다. 전산유체 해석을 통하여 흡입구 내부흐름을 실험결과 값과 비교 분석하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제18권1호
• /
• pp.81-91
• /
• 1994

Combustion noise involved with chemical heat release and turbulent process in turbopropulsion systems, gasturbine, industrial furnaces and internal engines is indeed noisy. The experimental study reported in this paper is made to identify a dominant combustion noise in jet flames. Gaseous propane and kerosene fuel have been used with air as the oxidizer in a different jet combustion systems. Combustion and aerodynamic noise are studied through far field sound pressure measurements in an anechoic chamber. And also mean temperature and velocities and turbulent intensities of both isothermal and reacting flow fields were measured. It is shown that axial mean velocity of reacting flow fields is higher about 1 to 3m/sec than that of cold flow in a gaseous combustor. As the gaseous fuel flow rate increases, the acoustic power increases. But the sound pressure level for the spray flame decreases with increasing equivalence ratio. The influence of temperature in the combustion fields due to chemical heat release has been observed to be a dominant noise source in the spray flame. The spectra of combustion noise in gaseous propane and kerosene jet flame show a predominantly low frequency and a broadband nature as compared with the noise characteristics in an isothermal air jet.

• 한국분무공학회지
• /
• 제16권3호
• /
• pp.146-151
• /
• 2011

LPG(Liquified Petroleum Gas) fuel for vehicles has lots of advantages such as low emission level, cheaper fuel cost and enough infrastructure. Therefore it arouses interest as an alternative engine to reduce emission of diesel engines. Especially MPI(Multi Point Injection) type LPLi(Liquid Phase LPG injection) system could have overcome the disadvantages of mixer types such as low engine performance, decreased charging efficiency and cold starting difficulty. However ice formation on the nozzle tip and intake port due to the freezing of moisture around the components is often observed in LPLi systems. This icing phenomenon is the direct cause of unstable engine combustion, resulting in engine emissions. Therefore in this research, a spray visualization test for LPG injection was carried out to obtain the basic information of an LPLi injector, then the effects of butane and propane mixing rates on ice formation at the intake port and nozzle tip was investigated. As a result, the icing characteristics of them showed contrary results according to the mixing rates.