• 한국강구조학회 논문집
• /
• 제14권5호통권60호
• /
• pp.657-664
• /
• 2002

본 논문은 새로운 냉간성형 각형강관 T형 접합부의 최대내력과 변형제한치에 대한 연구이다. 새로운 T형 접합부의 형상은 지관을 주관에 대하여 $45^{\circ}$ 회전시켜서 용접하는 형상이고, 지난 보고의 지관 $45^{\circ}$ 회전형 T형 접합부 실험결과 중에서 주관플랜지 휨 파괴가 지배하는 접합부만을 대상으로 설정하였다. $16.7{\leq}2{\gamma}(=B/T){\leq}33.3$ 이고 $0.27{\leq}{\beta}(=b1/B){\leq}0.6$ 범위의 지관 $45^{\circ}$ 회전형 T형 접합부에 대하여, 최대내력을 정의를 위한 변형제한치는 주관폭의 3% 변형량(3%B)으로 제안하였다. 기본형에 대한 기존의 항복선모델을 검토하고, 지관 회전형에 대한 새로운 항복선모델을 제안하였다. 최종적으로 항복선해석에 근거한 내력식과 실험결과를 비교하고, 제안내력식의 적용범위를 제시하였다.

• Steel and Composite Structures
• /
• 제50권6호
• /
• pp.675-688
• /
• 2024

Cold-formed steel (CFS) is prone to buckling failure under loading. Lightweight concrete (LC) made of lightweight aggregate has light weight and excellent thermal insulation performance. However, concrete is brittle in nature which is why different materials have been used to improve this inherent behavior of concrete. The distortional buckling (DB) performance of cold-formed steel-lightweight concrete (CFS-LC) composite columns was investigated in this paper. Firstly, the compressive strength test of foam concrete (FC) and ceramsite concrete (CC) was carried out. The performance of the CFS-LC members was investigated. The test results indicated that the concrete-filled can effectively control the DB of the members. Secondly, finite element (FE) models of each test specimen were developed and validated with the experimental tests followed by extensive parametric studies using numerical analysis based on the validated FE models. The results show that the thickness of the steel and the strength of the concrete-filled were the main factors on the DB and bearing capacity of the members. Finally, the bearing capacity of the test specimens was calculated by using current codes. The results showed that the design results of the AIJ-1997 specification were closer to the experimental and FE values, while other results of specifications were conservative.

• 대한기계학회논문집B
• /
• 제25권3호
• /
• pp.277-284
• /
• 2001

One of the problems in a refrigerator operation is the frost formation on a cold surface of the evaporator. The frost layer is formed by the sublimation of water vapor when the surface temperature is below the freezing point. This frost layer is usually porous and formed on the cold surface of the evaporator. The frost layer on the surface of a evaporator will make side effect such as thermal resistance. However, these important factors have not been used in determining the defrosting period. Therefore, the proper defrosting operation period based on the new defrosting method is very important, and make a comparison between conventional method like electric defrost and new method in compression work, evaporation pressure, evaporation temperature.

• Steel and Composite Structures
• /
• 제34권3호
• /
• pp.347-359
• /
• 2020

The objective of this study is to experimentally scrutinize the axial performance of built-up concrete filled steel tube (CFT) columns composed of steel plates. In this case, the main parameters cross section types, compressive strength of filled concrete, and the effect of welding lines. Welded built-up steel box columns are fabricated by connecting two pieces of cold-formed U-shaped or four pieces of L-shaped thin steel plates with continuous penetration groove welding line located at mid-depth of stub column section. Furthermore, traditional square steel box sections with no welding lines are investigated for the comparison of axial behavior between the generic and build-up cross sections. Accordingly, 20 stub columns with thickness and height of 2 and 300 mm have been manufactured. As a result, welding lines in built-up specimens act as stiffeners because have higher strength and thickness in comparison to the plates. Subsequently, by increasing the welding lines, the load bearing capacity of stub columns has been increased in comparison to the traditional series. Furthermore, for specimens with the same confinement steel tubes and concrete core, increment of B/t ratio has reduced the ductility and axial strength.

• Steel and Composite Structures
• /
• 제34권3호
• /
• pp.333-345
• /
• 2020

In the past, many efficient profiles have been developed for cold-formed steel (CFS) members by judicious intermediate stiffening of the cross-sections, and they have shown improved structural performance over conventional CFS sections. Most of this research work was based on numerical modelling, thus lacking any experimental evidence of the efficiency of these sections. To fulfill this requirement, experimental studies were conducted in this study, on efficient intermediately stiffened CFS sections in flexure, which will result in easy and simple fabrication. Two series of built-up sections, open sections (OS) and box sections (BS), were fabricated and tested under four-point loading with same cross-sectional area. Test strengths, modes of failure, deformed shapes, load vs. mid-span displacements and geometric imperfections were measured and reported. The design strengths were quantified using North American Standards and Indian Standards for cold-formed steel structures. This study confirmed that efficient profiling of CFS sections can improve both the strength and stiffness performance by up to 90%. Closed sections showed better strength performance whereas open sections showed better stiffness performance.

• International Journal of Concrete Structures and Materials
• /
• 제7권1호
• /
• pp.51-59
• /
• 2013

The use of light-gauge steel framing in low-rise commercial and industrial building construction has experienced a significant increase in recent years. In such construction, the wall framing is an assembly of cold-formed steel (CFS) studs held between top and bottom CFS tracks. Current construction methods utilize heavy hot-rolled steel sections, such as steel angles or hollow structural section tubes, to transfer the load from the end seats of the floor joist and/or from the load-bearing wall studs of the stories above to the supporting load-bearing wall below. The use of hot rolled steel elements results in significant increase in construction cost and time. Such heavy steel elements would be unnecessary if the concrete slab thickening on top of the CFS wall can be made to act compositely with the CFS track. Composite action can be achieved by attaching stand-off screws to the track and encapsulating the screw shank in the deck concrete. A series of experimental studies were performed on full-scale test specimens representing concrete/CFS flexural elements under gravity loads. The studies were designed to investigate the structural performance of concrete/CFS simple beams and concrete/CFS continuous headers. The results indicate that concrete/CFS composite flexural elements are feasible and their structural behavior can be modeled with reasonable accuracy.

• 한국강구조학회 논문집
• /
• 제10권4호통권37호
• /
• pp.677-689
• /
• 1998

본 연구에서는 중심압축력을 받는 스털스터드의 설계강도에 대하여 다루었으며 비교 평가하였다. 미국규준인 냉간성형 LRFD 설계규준 (AISI). 유럽의 냉간박벽부재설계규준 (EC3 part 1.3) 및 독일의 관련규정 (DASt-Richtlinie 016)의 유사성과 차이점을 소개하고 분석하며 체계적으로 평가하였다. 특히 유효폭과 전체 안정성문제 (휨좌굴과 비틀림좌굴)가 이 논문에서 내포되어 있다. 또한 예제를 통하여 두 규준인 AISI와 EC3에 의한 설계압축강도를 산정하고 비교 분석하였다.

• 한국강구조학회 논문집
• /
• 제13권4호
• /
• pp.373-380
• /
• 2001

본 연구에서는 벽 패널의 부분 합성거동 해석에 대하여 거론한다. 기 발표된 목재 바닥 시스템으로부터 유도된 처짐공식을 소개하고, 이 공식을 적용하여 석고보드와 강재 샛기둥으로 결합된 합성벽 패널의 중앙지점 처짐값을 산정한다. 나사연결부의 불완전성(미끄럼), 국부좌굴, 샛기둥 복부의 개구부, 그리고 인접 석고보드간의 불연속으로 야기 될 수 있는 강성의 감소 등을 처짐공식에 적절히 반영하는데 그 목적을 두었다. 적용된 처짐공식으로 산정된 처짐 기대치와 실험 관측치간의 비교에서는, 나사연결부의 상한 강성치를 사용한 처짐 기대치가 실험 관측치와 가장 근접한 결과를 보였다.

• Steel and Composite Structures
• /
• 제15권5호
• /
• pp.519-538
• /
• 2013

The design optimization of a cold-formed steel portal frame building is considered in this paper. The proposed genetic algorithm (GA) optimizer considers both topology (i.e., frame spacing and pitch) and cross-sectional sizes of the main structural members as the decision variables. Previous GAs in the literature were characterized by poor convergence, including slow progress, that usually results in excessive computation times and/or frequent failure to achieve an optimal or near-optimal solution. This is the main issue addressed in this paper. In an effort to improve the performance of the conventional GA, a niching strategy is presented that is shown to be an effective means of enhancing the dissimilarity of the solutions in each generation of the GA. Thus, population diversity is maintained and premature convergence is reduced significantly. Through benchmark examples, it is shown that the efficient GA proposed generates optimal solutions more consistently. A parametric study was carried out, and the results included. They show significant variation in the optimal topology in terms of pitch and frame spacing for a range of typical column heights. They also show that the optimized design achieved large savings based on the cost of the main structural elements; the inclusion of knee braces at the eaves yield further savings in cost, that are significant.

• Steel and Composite Structures
• /
• 제23권3호
• /
• pp.331-338
• /
• 2017

Cold-formed lipped channel columns (CFLCCs) have been widely used in light gauge steel constructions. The distortional buckling is one of the important buckling modes for CFLCCs and the distortional buckling critical load depends significantly on the rotational restrain stiffness generated by the web to the lipped flange. First, a simplified explicit expression for the rotational restraint stiffness of the lipped flange has been derived. Using the expression, the characteristics of the rotational restraint stiffness of the lipped flange have been investigated. The results show that there is a linear coupling relationship between the applied forces and the rotational restraint stiffness of the lipped flange. Based on the explicit expression of the rotational restraint stiffness of the lipped flange, a simplified analytical formula has been derived which can determine the elastic distortional buckling critical stress of the CFLCCs subjected to axial compression. The simplified analytical formula developed in this study has been shown to be accurate through the comparisons with results from the distortional buckling analyses using the ANSYS finite element software. The developed analytical formula is easy to apply, and can be used directly in practical design and incorporated into future design codes and guidelines.