• 한국정보전자통신기술학회논문지
• /
• 제15권1호
• /
• pp.8-13
• /
• 2022

본 논문에서는 RF (Radio Frequency) 에너지 하베스팅 센서 노드의 설계 방안과 CATV 망과 누설 동축 케이블 (leaky coaxial cable)을 활용한 센서 네트워크 구축 방안을 연구하였다. 센서 노드는 915MHz 주파수 대역에서 동작하는 WPTS (Wireless Power Transfer System) 전력 수신기로 전원공급부를 설계하였다. WOC (WiFi over Coax) 기술을 활용하여 CATV 망으로 센서의 BLE 무선통신 신호와 WPTS 전력 송신기 신호를 전송하고, 누설 동축 케이블로 RF 신호를 방사시키는 센서 네트워크 구축 방안을 제안하였다. 센서 네트워크를 구축하는 지점에 누설 동축 케이블을 활용하면 센서 노드의 수신 신호 강도 지표가 허용되는 최소값 (-78dBm)을 만족하는 지점까지 센서 네트워크의 커버리지를 확장할 수 있다.

• Structural Monitoring and Maintenance
• /
• 제10권2호
• /
• pp.133-154
• /
• 2023

Obscured structural members are mostly under-evaluated during condition assessment due to lack of visual inspection capability. Insufficient information about the integrity of these structural members poses a significant risk for public safety. Time domain reflectometry (TDR) is a novel approach in structural health monitoring (SHM). Ordinary coaxial cables "as is" without a major modification are not suitable for SHM with TDR. The objective of this study is to propose a practical and cost-effective modification approach to commercially available coaxial cables in order to use them as a "cable sensor" for damage detection with the TDR equipment for obscured structural members. The experimental validation and assessment of the proposed modification approach was achieved by conducting 3-point bending tests of the model piles as a representative obscured structural member. It can be noted that the RG59/U-6 and RG6/U-4 cable sensors expose higher strain sensitivity in comparison with non-modified "as is" versions of the cables used. As a result, the cable sensors have the capability of sensing both the presence and the location of a structural damage with a maximum aberration of 3 cm. Furthermore, the crack development can be monitored by the RG59/U-6 cable sensor with a simple calibration.

• 전기학회논문지
• /
• 제61권2호
• /
• pp.251-256
• /
• 2012

This study deals with the location of partial discharges(PDs) for power cables and GIS using 2 PD sensors and long coaxial signal cables. Throughout the experiments by use of simulated PD pulses and corona discharges in the power cable system, it is found out that the impedance matching between the coaxial signal cable and the measuring equipment should be done for good S/N ratio and the on-site measurement using more than 100m-long coaxial signal cable is possible. In addition, new PD location algorithm with the polarities of PD pulses and the arrival time difference between two pulses was proposed and was proved through the partial discharge experiments for the cable joint defect and artificial void defect.

• 한국자기학회지
• /
• 제17권2호
• /
• pp.55-59
• /
• 2007

본 논문에서는 Co를 주성분으로 하는 아몰퍼스 자성 와이어를 동축케이블의 신호선으로 하는 자계센서를 제작하여 외부자계에 대한 특성을 측정하였다. 측정된 임피던스의 주파수의존성에는 전송선로의 공진특성이 반영되었으며 인가자계가 없을 때, 1/4 파장에 해당하는 주파수가 250 MHz에서 나타났다. 측정 주파수대역에서는 표피효과에 의한 저항성분이 임피던스를 거의 결정하였으며 또한 외부자계가 $0\;Oe{\sim}1\;Oe$ 사이에서 임피던스는 자성 아몰퍼스와이어의 투자율의 변화에 의해 크게 변화하였다. 0.1 Oe 부근에서 150 MHz의 ${\Delta}Z/{\Delta}H$가 $300{\Omega}/Oe$이라는 매우 큰 값이 얻어져 Co를 주성분으로 하는 자성와이어를 동축케이블형 자계센서로 사용하는 경우 센서로서 매우 유용함을 알 수 있었다.

• Smart Structures and Systems
• /
• 제1권4호
• /
• pp.385-404
• /
• 2005

The paper presents a model to calculate reinforcement strain using measured crack width in members under applied tension, flexure, and/or shear stress. Crack mapping using a new type of distributed coaxial cable sensors for health monitoring of large-scale civil engineering infrastructure was recently proposed and developed by the authors. This paper shows the results and performance of such sensors mounted on near surface of two flexural beams and a large scale reinforced concrete box girder that was subjected to cyclic combined shear and torsion. The main objectives of this health monitoring study was to correlate the sensor's response to strain in the member, and show that magnitude of the signal's reflection coefficient is related to increases in applied load, repeated cycles, cracking, and reinforcement yielding. The effect of multiple adjacent cracks, and signal loss was also investigated. The results shown in this paper are an important step in using the sensors for crack mapping and determining reinforcement strain for in-situ structures.

• 전기학회논문지
• /
• 제56권12호
• /
• pp.2196-2201
• /
• 2007

Materials used at microwave are usually used as a dielectric with a manufacturing purpose of printed circuit boards, etc. Complex permittivity of them can be measured from attenuation constant or propagation constant of a transmission line using a microstrip line with bulk type. But as the technique recently which can manufacture to have complex permittivity and permeability demanded using nonferrous metals for powder-type grows up, we need sensors and methods which can measure characteristics of powder-type materials. So far measuring methods of permittivity and permeability with waveguide or coaxial cable are used but they have faults which have a complex measurement method and are difficult to simultaneously measure permittivity and permeability. In this paper, a simultaneous measuring method of permittivity and permeability with 2-port coaxial cable and a new proposed calculation. The proposed 2-port coaxial cable is designed to be easy to insert materials and to have a wideband. We measure permittivity and permeability of magnetic powder(Ni-Fe-Mo, Ni-Fe) which reveal its characteristic at $0.3{\sim}1.3GHz$ to identify the proposed sensor.

• Journal of Magnetics
• /
• 제18권2호
• /
• pp.159-162
• /
• 2013

We present how to optimize the operation condition including frequency of the orthogonal fluxgate sensor in this paper. The orthogonal fluxgate sensor was fabricated with a Co-based amorphous wire with 10 mm long and 100 ${\mu}m$ in the diameter and a 270-turn pickup coil wound on the amorphous wire. In order to investigate the frequency dependence of the sensitivity, output spectra of the sensor which was connected by using a coaxial cable with various lengths of 0.5-5 m were measured with a RF lock-in amplifier. The maximum sensitivities were obtained at different frequencies according to coaxial cable lengths. It was found that the optimal operation frequencies, at which maximum sensitivities were appeared, were almost identical to the frequencies of impedance resonance. The maximum sensitivity and optimal operation frequency were 1.1 V/Oe (${\approx}$ 11000 V/T) and 1.25 MHz respectively.

• 융합보안논문지
• /
• 제12권3호
• /
• pp.27-34
• /
• 2012

본 논문에서는 IEEE와 ZigBee Alliance에서 제정한 국제 표준안과 호환성을 가지고, 저전력 저비용을 강점으로 하는 지그비를 이용하여 상대적으로 열악한 전송 환경을 갖지만 적용이 용이한 무선망과, 기존 무선 기반 센서 네트워크 단점을 극복하기 위해 이미 구축되어 있는 동축케이블을 이용한 유선망을 연동함에 있어서 RSSI 모니터링을 통한 출력파워 조절 알고리즘을 이용하여 저전력 소모를 특징으로 하는 지그비 장치의 새로운 저전력 소모 방안을 제시하였다. 보다 최적화된 저전력 소모를 가능하도록 실험을 통해 RSSI 모니터링을 통한 출력 파워 조절 알고리즘의 유효성을 검증하였다.

• 한국인터넷방송통신학회논문지
• /
• 제9권4호
• /
• pp.1-8
• /
• 2009

본 연구 이전에 제안되었던 실시간 교량 모니터링 시스템은 교량 곳곳에 배치되어 있는 센서들로부터 중앙서버로 동축 케이블을 통해 데이터를 송수신하였는데, 동축 케이블을 이용하여 교량 전체의 센서들의 네트워크를 구성하기 위해서는 막대한 인력과 비용이 따르게 된다. 본 연구에서는 USN을 기반으로 한 교량 모니터링 시스템 제안하고, 이에 대한 프로토타입을 설계 및 구현하였다. HSDPA를 통해 얻은 센싱 데이터 값을 TCP/IP 소켓을 통해 교량 모니터링 서버에 전달함으로써 양방향 통신을 구축하여 그래프 변환을 하는 전체 시스템을 구현하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.79-86
• /
• 2010

In this paper, using soil slope inclinometer observations of lateral flow is used as a traditional way, but there are some decisions. Inclinometers in the process of installing and monitoring is costly. Severe incline slope of the lateral flow is observed in the inefficient. As a solution for it using TDR sensors are used to. Metal conductors such as coaxial cable and general cable uses a measurement sensor can be installed on site at a lower cost and slope measurements are available for long-term monitoring. When TDR sensor is installed on the slopes, changes in the behavior of slopes causes the earth pressure. TDR sensors determine the change of earth pressure and tried to analyze the behavior of slopes.