• Journal of Information Display
• /
• 제5권4호
• /
• pp.27-30
• /
• 2004

This paper investigates the effects of coating such as Invar (Fe-36% Ni), Fe-Ni Alloys and $WO_3$ on the doming property of aluminum killed (AK) shadow masks, which may be used for flat CPTs. Invar and Fe-Ni Alloys are deposited on AK shadow mask in plasma atmosphere and annealed. $WO_3$ is screen-printed on the deposited layer. The coating is observed to cause a decrease in the doming property of the shadow masks due to their lower thermal expansion coefficients and anti-doming properties.

• 대한조선학회논문집
• /
• 제43권2호
• /
• pp.268-274
• /
• 2006

Analysis has been made of the anti-corrosive property of organic coating under the shear stress of the flow by means of AC impedance method. Marine anti-corrosive painted panels were placed in the water channel with varying flow rate, thereby experiencing varying flow shear stress on the surfaces. The velocities of the salt water were ranged from 1.48 to 5.2 m/s and the coating thickness of from $70{\mu}m\;to\;140{\mu}m$. For all coating thicknesses investigated, the poorer anti-corrosive property and the lower adhesion strength have been found for the higher shear stress. It has been found that the shear stress accelerates the aging of organic marine coatings.

• Bulletin of the Korean Chemical Society
• /
• 제30권11호
• /
• pp.2584-2588
• /
• 2009

The effect of $LaF_3$ coating on the structural and electrochemical properties of $Li[Ni_{0.3}Co_{0.4}Mn_{0.3}]O_{2}$ cathodes was investigated using XRD, SEM, TEM, and a cycler. The coating layer consisted of nano-sized particles attached nonuniformly to the surface of pristine powder. Despite the surface coating treatment, phase difference by $LaF_3$ coating was not detected. The discharge capacities of coated electrodes were a little lower than that of pristine sample at a 1 C rate. However, as the C rate increases, the capacity retention of the coated sample becomes obviously superior to that of the pristine sample. The cyclic performances of the electrodes in the voltage range of 4.8 $\sim$ 3.0 V were also improved by the surface coating. Such enhancement is attributed to the presence of the $LaF_3$ coating layer, which effectively suppressd the reaction between electrodes and electrolytes on the surface of the $Li[Ni_{0.3}Co_{0.4}Mn_{0.3}]O_{2}$ electrode.

• Corrosion Science and Technology
• /
• 제22권2호
• /
• pp.99-107
• /
• 2023

Layered silicate clay montmorillonite (MMT) has been used in nanocomposite coating to improve corrosion protection by reinforcing the barrier property. The better dispersion of MMT in the coating produces a higher barrier effect. Pretreatment with MMT could favor the delamination of clay platelets, facilitating MMT dispersion in the coating. In the present work, a montmorillonite/silica (MMT/Si) composite was prepared by the in situ sol-gel method. x-ray diffraction measurements and field-emission scanning electron microscopy observations showed silica crystal formation and increased basal spacing between the MMT platelets. Composite MMT/Si particles were introduced in an epoxy resin to reinforce the corrosion protection of the coating applied on the AA2024 surface. Electrochemical impedance spectroscopy (EIS) was performed to characterize the protective property of the coating. The results demonstrated the high barrier effect of the coating containing 5 wt% of MMT/Si. Adhesion evaluation after a salt spray test exhibited a high adherence to the epoxy coating containing MMT/Si.

• 해양환경안전학회지
• /
• 제5권2호
• /
• pp.15-26
• /
• 1999

The marine structures with sea water cooling system always expose to the oceanic atmosphere. Therefore, the protection of the equipments is very important. To investigate the effectiveness of advanced composite materials for the application in offshore environments, the tensile test, hardness test, undercutting property test, permeance test and the friction and wear test were carried out by using various applicable coating materials. The main results obtained can be summarized as follows; 1. The micro-hardness of the Archcoat 502B showed the highest value. 2. The coefficient of friction of the Rigspray coating at the speed of 2.21m/sec showed the lowest value, and that of the Archcoat 502B coating at 1.08m/sec and 0.18m/sec indicated the lowest values. 3. The wear mass at the speed of 0.18m/sec and 1.08m/sec in dry condition showed the smallest values. 4. The Archcoat 502B coating is fitted to the dynamic instruments in the range of low speed and middle speed. Rigspray coating is fitted to the dynamic instruments in the range of high speed. 5. The wear mass of five kinds of coating materials at the range of low speed was very small, and those of the Archcoat S02B, Archcoat 402B and Rigspray coating at high speed range were quitely smaller than those of the Modified Epoxy and Tar Epoxy.

• 펄프종이기술
• /
• 제32권4호
• /
• pp.41-48
• /
• 2000

The main objective of this study was to investigate the packing state and optical properties of coated paper prepared with different coating colors by varying the blending ratio of such pigment as clay, $CaCO_3$, and plastic pigment. To evaluate the effect of packing state of pigment on the properties of coated paper, the coating thickness, which was theoretically calculated by specific gravity, and packing volume of pigment were used. It was found that there exists close relationship between the coating thickness and surface property of coated paper. For instance, the macro roughness(smoothness) of coated paper is closely related to bulkiness. Plastic pigments used in this research has a high finishing efficiency on the light weight coatings. Especially, hollow sphere pigment was very effective for improving the property of coated paper produced in this test. And when HSP was blended with $CaCO_3$the surface property such as smoothness and gloss improved significantly.

• 한국공작기계학회논문집
• /
• 제15권1호
• /
• pp.49-55
• /
• 2006

The effect of coating temperature with regard to surface properties of TiN-coated layer on hard metal(WC-Co) are experimentally investigated. Hardness, surface roughness, TiN coating thickness and adsorption force were measured in order to evaluate the effect of coating temperature. The two-way ANOVA method is used in order to evaluate the experimental data. In AIP processing, It is concluded that the furnace temperature in the range of $400^{\circ}C\~500^{\circ}C$ affected to a little increasing the number of production with the coating temperature.

• 한국표면공학회지
• /
• 제29권6호
• /
• pp.745-752
• /
• 1996

Wear property of plasma spray coating in $Cr_2O_3$ powder manufatured of spray dry method on the aluminum substrate was inspected for the application of piston-ring of automotive enginel. The plama spray coatings were varied with feed rate and particle size. Used the ball-on disc type tribometer, wear volume, friction, surface rougness were investigated. The delamination of the coating layer were observed with SEM. Also the cross-section of wear track were investigated, using optical microscopy. As a result of experiment, wear mechanism was addressed in the various coating process.

• 한국결정성장학회지
• /
• 제18권3호
• /
• pp.131-135
• /
• 2008

본 연구에서는 합성운모에 대한 코팅기술을 확립한 뒤, 비수성을 나타내는 합성운모를 제조하였다. 합성운모의 표면코팅은 고속교반기를 사용하여 행하였으며, 스테아린산으로 코팅된 합성운모의 특성은 침적실험, XRD 및 SEM을 이용하여 분석하였다. 본 연구 결과, 교반기의 내부온도는 $70^{\circ}C$를 유지하고, 10분 동안 1600 rpm/min을 행함으로써 운모 표면에 스테아린산의 코팅이 가능하였다. 또한 SEM 관찰결과로부터, 스테아린산과 운모의 혼합비율, 교반기 내부온도, 회전속도에 의해 특성이 변화하는 반면 코팅처리시간과는 무관함을 알 수 있었다.

• Journal of the Korean Wood Science and Technology
• /
• 제25권4호
• /
• pp.10-16
• /
• 1997

This study was carried out to improve coating structure by controlling the electrostatic interaction of coating components and by changing the coating structure of coated paper prepared with amphoteric and anionic latices. The results indicated that amphoteric latex copolymerized with carboxylic and amine groups had stronger interaction with other coating components than anionic latex with branched carboxylic group by controlling pH. These properties of amphoteric latex showed positive effects on viscosity rheology, and supernatant sediment of coating color. The coated paper using amphoteric latex had also produced more porous and smoother coverage of the coating layer than that using anionic latex. This porous and smooth coating layer showed better optical properties and printability than those of anionic latex such as opacity, porosity, ink set-off, and wet ink receptivity.