• Proceedings of the KSRS Conference
• /
• 2005.10a
• /
• pp.721-724
• /
• 2005

In this study the spatial distribution characters of forest in forest damaged area were first considered by analyzing spatial data and monitoring forest landscape. Then suitable tree species on each site were selected through the weighted score analysis of GIS analysis methods. Finally, the best forest stand arrangement method could be presented on the 3D based simulation system for the advanced reforestation technology in Korea. For this purpose, the virtual reforestation system was implemented by using the concept of virtual GIS and CBD (Component Based Development) method. By use of this system the change offorest landscape of burnt forest area some years after reforestation practice could be detected and monitored by applying the site index and 3D modeling method.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.2
• /
• pp.167-173
• /
• 2011

This paper presents a method for the development of the impedance locus to test the dynamic characteristics of protective relays. Specifically, using the proposed method, the impedance locus can comprise three impedance points, and the speed of impedance trajectory can be adjusted by frequency deviation. This paper is divided into two main sections. The first section deals with the configuration of impedance locus with voltage magnitude, total impedance magnitude, and impedance angle. The second section discusses the control of the locus speed with the means of the deviation between two frequencies. The proposed method is applied to two machine equivalent systems with offline simulation (i.e., PSCAD) and real-time simulation (i.e., real-time simulation environment) to demonstrate its effectiveness.

• Journal of the Korean Society of Combustion
• /
• v.6 no.2
• /
• pp.23-28
• /
• 2001

In the present work, the effect of PDF selection and intermittency on the result of the numerical simulation are examined by the simulation of a turbulent methane-air jet diffusion flame. As to the PDFs, beta-function and clipped Gaussian are considered. Results for the pure mixing jet are compared with experimental results. Then, the turbulent flame is calculated for the same conditions and the results obtained for the several models are compared. It is found that the clipped Gaussian distribution coupled with consideration of intermittency recovers the experimental data very well. As to the reacting flow results, the main overall properties of the turbulent jet diffusion flame such as maximum flame temperature are less affected by the choice of the PDF. Flame height and NO emissions, on the contrary, appear to be significantly influenced.

• Journal of the Korean Society of Safety
• /
• v.25 no.1
• /
• pp.9-16
• /
• 2010

Flame structure of diffusion flame interacting with a single vortex was investigated with direct numerical simulation (DNS). A well-known counterflow diffusion flame was used as an initial flat flame and single vortices were made by issuing a high-velocity jet abruptly in fuel- and air-side. The variations in the maximum concentration of major species (CO and $CO_2$) and NOx (NO and $NO_2$) with the stoichiometric scalar dissipation rate were investigated. Unsteady effects in the species concentration variation of the flame interacting with a vortex were identified by comparing with that of steady flame. $NO_2$ formation characteristics of the flame interacting with a vortex were well understood by investigating the $HO_2$ formation. To enhance the prediction performance in the fire simulation, current turbulent combustion modelings are needed to be modified by adopting the unsteady effects in the species concentrations of diffusion flame interacting with a vortex.

• Structural Engineering and Mechanics
• /
• v.2 no.3
• /
• pp.227-244
• /
• 1994

The purpose of this investigation is to propose a numerical simulation method of the crack propagation behavior in 3-dimensionl elastic body. The simulation method is based on the displacement-type finite element method, and the linear fracture theory is introduced. The results from the proposed method are compared with those from the structural experiments, and the good coincidences between them are shown in this paper. At the same time, 2-dimensional analysis is also done, and the results are compared with those obtained from 3-dimensional analysis and the structural experiments.

• 제어로봇시스템학회:학술대회논문집
• /
• 1988.10b
• /
• pp.875-878
• /
• 1988

In this work it is shown how the methods used in chemical engineering for the analysis and simulation of processes may be applied to the actual phosphoric acid plant. Attention has been focused on the dihydrate process for which the necessary fundamental experimental data and plant operation data are available. The results of the simulation have shown that a reasonable description of the process at hand is possible by the proposed method. However, because of the complexity of the process, of the limited basic experimental data reported in literature, and the limitations of mathematics, the model was somewhat idealized and gave a reliable representation of the influence of only a few of the variables that affect the performance of the plant.

• Journal of Welding and Joining
• /
• v.21 no.3
• /
• pp.30-34
• /
• 2003

This paper describes the heat distribution characteristics of ASTM A131DH36 high tensile steel for ship structures in 5㎾ $CO_2$ laser welding. In general, high energy of laser beam concentrates on the small area of the weldment instantaneously; therefore, this heat transfer mechanism induces the rapid changes of temperature and mechanical characteristics in laser welds this mechanism. So temperature distribution analysis is important to understand mechanical characteristics of laser welds. Authors have conducted finite element simulation to analyze the heat distribution characteristics in laser welds. The result of simulation has been verified by comparing with the metallurgical experiment result. From the result of this study, we can accurately predict the heat distribution characteristics in laser welds by using numerical simulation.

• Journal of Information Display
• /
• v.8 no.4
• /
• pp.1-4
• /
• 2007

In the present study, we propose Monte Carlo simulation that takes into consideration the interface phenomena between liquid crystal and substrate. We use rigid model molecules of liquid crystal and substrate. Interface is generated using potential field that induces decomposition of molecules. We use hard spherocylinders as model liquid crystal molecules. Substrate is modeled as region composed of shorter spherocylinders. Our results show that there is a case in which nematic order is reinforced in the vicinity of rubbed substrate.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.6 no.9
• /
• pp.2153-2169
• /
• 2012

Femtocells provide high quality indoor communications with low transmit power. However, when femtocells are applied in cellular systems, a co-channel interference problem between macrocells and femtocells occurs because femtocells use the same spectrum as do the macrocells. To solve the co-channel interference problem, a previous study suggested a resource allocation scheme in LTE cellular systems using FFR. However, this conventional resource allocation scheme still has interference problems between macrocells and femtocells near the boundary of the sub-areas. In this paper, we define an optimization problem for resource allocation to femtocells and propose a femtocell resource allocation scheme to solve the optimization problem and the interference problems of the conventional scheme. The evaluation of the proposed scheme is conducted by System Level Simulation while varying the simulation environments. The simulation results show that the proposed scheme is superior to the conventional scheme and that it improves the overall performance of cellular systems.

• Proceedings of the KIEE Conference
• /
• 2001.07a
• /
• pp.237-239
• /
• 2001

This paper describes the digital relay simulator system using digital signal processor. The simulator system has two parts, one is software and the other is hardware part. The simulation software has variety calculation engines ; EMTP simulation data file conversion, user define simulation data generation, sequence data generation, data analysis engines. etc, these are designed upon GUI. And simulator software provides easy control interface for users, the simulator software performs on every MS Windows OS. The simulator hardware design uses 32bit floating point DSP(TMS320C32) architecture to achieve flexibility and high speed operation.