• 한국해양공학회지
• /
• 제33권4호
• /
• pp.364-376
• /
• 2019

When underwater blasting is conducted, both shock waves and water waves have an effect on adjacent coastal areas. In this study, an empirical formula for estimating the details of water waves caused by underwater blasting was applied to a non-reflected wave generation system, and a 3D numerical wave tank (NWT) was improved to reproduce the generation and propagation of such water waves. The maximum elevations of the propagated water waves were comparatively analyzed to determine the validity and effectiveness of the NWT. Good agreement was demonstrated between the empirical and simulation results. The generation and propagation of water waves were also simulated under each underwater blasting scenario for the removal of the Todo islet at the Busan Newport International Terminal (PNIT). It was determined that the water waves generated by the underwater blasting scenario examined in this study did not have a significant impact on the PNIT. In addition, multiple-charge blasting caused higher wave heights than single-charge blasting. As the amount of firing charge increased, the wave height also increased. Finally, larger water waves were generated during the later blasting conducted at a deeper depth as compared with an earlier blasting conducted at a relatively shallow depth.

• 한국결정성장학회지
• /
• 제33권6호
• /
• pp.210-215
• /
• 2023

조합 원료의 소성성은 시멘트 제조 기술에서 매우 중요한 요소이며, 각 원료들의 물리적, 화학적 및 광물학적 특성에 의해 좌우된다. 본 연구에서는 국내산 석탄재와 일본산 석탄재를 시멘트 원료로 사용했을 경우, Lafarge 평가 방법과 Polysius 평가 방법을 이용하여 소성성을 비교하였다. 석탄재의 종류와 투입량에 관계없이 석탄재를 사용하였을 경우가 석탄재를 사용하지 않았을 때 보다 소성성이 향상됨을 알 수 있었다. 모든 종류의 석탄재에서 투입량이 증가할수록 소성성이 향상되었으나, 3 %까지 소성성의 향상이 뚜렷하였고 4 % 첨가 시에는 향상 폭이 상대적으로 크지 않았다. 결론적으로 시멘트의 품질이 허용하는 범위 내에서 석탄재의 투입량이 증가할수록 소성성이 향상되며, 따라서 클링커의 소성에 필요한 연료비의 절감도 기대할 수 있다.

• 대한환경공학회지
• /
• 제35권11호
• /
• pp.781-784
• /
• 2013

하수슬러지의 해양투기가 금지됨에 따라 하수슬러지의 적정처리에 대한 요구가 커지고 있다. 따라서 본 연구에서는 하수슬러지와 폐유리를 이용하여 경량벽돌을 제조하고자 하였다. 건축자재인 벽돌은 통상 $1,200^{\circ}C$ 이상의 고온에서 제조되기 때문에 벽돌 제조시 다량의 에너지가 소비된다. 본 연구에서는 하수슬러지와 폐유리를 이용하여 경량벽돌 제조시 $CO_2$ 배출량을 줄이기 위해 $800^{\circ}C$ 이하의 낮은 온도에서 지오폴리머 기술을 이용하여 벽돌을 제조하였다. 경량벽돌 제조시 소성온도, 하수슬러지와 폐유리 및 물유리와 물의 혼합비 등이 주요 영향 인자이며, 이들의 변화에 따른 경량벽돌의 특성을 평가하였다. 본 연구결과에 따르면 경량벽돌의 최적 제조조건은 소성온도 $750^{\circ}C$, 물유리/물 혼합비 1.5, 하수슬러지/폐유리 비 10 : 90 wt%였다. 이때 제조한 경량벽돌의 압축강도 5.1 MPa, 비중 0.46으로 발포세라믹 경량벽돌 기준을 만족시키는 것으로 나타났다.

• 한국결정성장학회지
• /
• 제28권3호
• /
• pp.123-129
• /
• 2018

고온 열처리 후에도 안정적인 발색 효과를 가지는 디지털 4원색(cyan, magenta, yellow, black; CMYK)의 세라믹 잉크를 활용한 세라믹 잉크젯 프린팅 기술은 다양한 제품의 디지털 이미지를 정확하고 빠르게 인쇄 가능하다는 장점을 가지고 건축 및 세라믹 산업 분야에서 기존 공정을 빠르게 대체하고 있다. 세라믹 잉크젯 프린팅 기술은 무기 안료의 분산 안정성과 함께 적절한 점도와 표면 장력을 필요로 하며 기존에는 이러한 요구조건에 부합하는 유기용매 기반의 잉크가 주로 사용되어져 왔으나 최근에는 VOCs가 발생하지 않는 환경친화적인 세라믹 잉크 소재에 대한 관심이 커지고 있다. 본 연구에서는 $CoAl_2O_4$ cyan 발색 무기안료와 alumino boro-silicate 유리 분말을 사용하여 친환경적인 수계 세라믹 복합잉크를 합성하고, 수계 시스템에서의 유변학적 물성과 분산성을 최적화하여 잉크젯 프린팅 공정에서의 토출성 및 프린팅 특성에 대해 연구하였다. 그 결과, 합성된 수계 세라믹 복합잉크는 점도 및 표면장력 조절을 통해 satellite drop이 발생하지 않는 토출 거동을 보였으며, 유리 기판 위에서도 높은 접촉각으로 인해 잉크 퍼짐 현상이 최소화되며 프린팅되는 것을 확인하였다.

• 대한치과보철학회지
• /
• 제45권2호
• /
• pp.169-181
• /
• 2007

Statement of problem: Titanium is well known as a proper metal for the dental restorations, because it has an excellent biocompatibility, resistance to corrosion, and mechanical property. However, adhesion between titanium and dental porcelains is related to the diffusion of oxygen to the reaction layers formed on cast-titanium surfaces during porcelain firing and those oxidized layers make the adhesion difficult to be formed. Many studies using mechanical, chemical and physical methods to enhance the titanium-ceramic adhesion have been actively performed. Purpose: This study meant to comparatively analyse the adhesion characteristics depending on different titanium surface coatings after coating the casts and wrought titanium surfaces with Au and TiN. Material and method: In this study, the titanium specimens (CP-Ti, Grade 2, Kobe still Co. Japan) were categorized into cast and wrought titanium. The wrought titanium was cast by using the MgO-based investment(Selevest CB, Selec). The cast and wrought titanium were treated with Au coating($ParaOne^{(R)}$., Gold Ion Sputter, Model PS-1200) and TiN coating(ATEC system, Korea) and the ultra low fusing dental porcelain was fused and fired onto the samples. Biaxial flection test was done on the fired samples and the porcelain was separated. The adhesion characteristics of porcelain and titanium after firing and the specimen surfaces before and after the porcelain fracture test were observed with SEM. The atomic percent of Si on all sample surfaces was comparatively analysed by EDS. In addition, the constituents of specimen surface layers after the porcelain fracture and the formed compound were evaluated by X-ray diffraction diagnosis. Result: The results of this study were obtained as follows : 1. The surface characteristics of cast and wrought titanium after surface treatment(Au, TiN, $Al_2O_3$ sandblasting) were similar and each cast and wrought titanium showed similar bonding characteristics. 2. Before and after the biaxial flection test, the highest atomic weight change of Si component was found in $Al_2O_3$ sandblasted wrought titanium(28.6at.% $\rightarrow$ 8.3at.%). On the other hand, the least change was seen in Au-Pd-In alloy(24.5at.% $\rightarrow$ 9.1at.%). 3. Much amount of Si components was uniformly distributed in Au and TiN coated titanium, but less amount of Si's was unevenly dispersed on Al2O3 sandblasting surfaces. 4. In X-ray diffraction diagnosis after porcelain debonding, we could see $Au_2Ti$ compound and TiN coating layers on Au and TiN coated surfaces and $TiO_2$, typical oxide of titanium, on all titanium surfaces. 5. Debonding of porcelain on cast and wrought titanium surface after the biaxial flection is considered as a result of adhesion deterioration between coating layers and titanium surfaces. We found that there are both adhesive failure and cohesive failure at the same time. Conclusion: These results showed that the titanium-ceramic adhesion could be improved by coating cast and wrought titanium surfaces with Au and TiN when making porcelain fused to metal crowns. In order to use porcelain fused to titanium clinically, it is considered that coating technique to enhance the bonding strength between coating kKlayers and titanium surfaces should be developed first.

• The Korean Journal of Physiology
• /
• 제18권1호
• /
• pp.19-35
• /
• 1984

Since the first report of Drury and $Szent-Gy{\ddot{o}}rgyi$ in 1929, the inhibitory influences of adenosine on the heart have repeatedly been described by many investigators. These studies have shown that adenosine and adenine nucleotides have overall depressant effects, similar to those of acetylcholine. Heart beats become slow and weak. It is also well known that adenosine is a potent endogenous coronary vasodilator. Many investigations on the working mechanisms of adenosine have been focused mainly on the effects of the coronary blood flow. However, the cellular mechanisms underlying the inhibitory action of adenosine on sinus node are not well understood yet. Thus, this study was undertaken to examine the behavior of rabbit SA node under influence of adenosine. In these series of experiments three kinds of preparations were used: whole atrial pair, left atrial strip, and isolated SA node preparations. The electrical activity of SA node was recorded with conventional glass microelectrodes 30 to 50 $M{\Omega}$. The preparations were superfused with bicarbonate-buffered Tyrode solution of pH 7.35 and aerated with a gas mixture of $3%\;CO_2-97%\;O_2$ at $35^{\circ}C$. In whole atrial pair, adenosine suppressed sinoatrial rhythm in a dose-dependent manner. Effect of adenosine on atrial rate appeared at the concentration of $10^{-5}M$ and was enhanced in parallel with the increase in adenosine concentration. Inhibitory action of adenosine on pacemaker activity was more prominent in the preparation pretreated with norepinephrine, which can steepen the slope of pacemaker potential by increasing permeability of $Ca^{+2}$. Calcium ions in perfusate slowly produced a marked change in sinoatrial rhythm. Elevation of the calcium concentration from 0.3 to 8 mM increased the atrial rate from 132 to 174 beats/min, but over 10 mM $Ca^{+2}$ decreased. The inhibitory effect of adenosine on sinoatrial rhythm developed very rapidly. Atrial rate was recovered promptly from the adenosine-induced suppression by the addition of norepinephrine, but extra $Ca^{+2}$ was less suitable to restore the suppression of atrial rate. Adenosine suppressed also atrial contractility in the same dosage range that restricted pacemaker activity, even in the reserpinized preparation. In isolated SA node preparation, spontaneous firing rate of SA node at $35^{\circ}C$(mean{\pm}SEM, n=16) was $154{\pm}3.3\;beats/min. The parameters of action potentials were: maximum diastolic potential(MDP), $-73{\pm}1.7\;mV: overshoot(OS), $9{\pm}1.4\;mV: slope of pacemaker potential(SPP), $94{\pm}3.0\;mV/sec. Adenosine suppressed the firing rate of SA node in a dose-dependent manner. This inhibitory effect appeared at the concentration of $10^{-6}M$ and was in parallel with the increase in adenosine concentration. Changes in action potential by adenosine were dose-dependent increase of MDP and decrease of SPP until $10^{-4}M$. Above this concentration, however, the amplitude of action potential decreased markedly due to the simultaneous decrease of both MDP and OS. All these effects of adenosine were not affected by pretreatment of atropine and propranolol. Lowering extra $Ca^{2+}$ irom 2 mM to 0.3 mM resulted in a marked decrease of OS and SPP, but almost no change of MDP. However, increase of perfusate $Ca^{2+}$ from 2 mM to 6 or 8 mM produced a prominent decrease of MDP and a slight increase of OS and SPP. Dipyridamole(DPM), which is known to block the adenosine transport across the cell membrane, definately potentiated the action of adenosine. The results of this experiment suggest that adenosine suppressed pacemaker activity and atrial contractility simultaneously and directly, by decreasing $Ca^{2+}-permeability$ of nodal and atrial cell membranes.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.176-176
• /
• 2009

Influences of dose and particle size of $Al_2O_3$ filler and sintering time on the dielectric properties of $Al_2O_3$ filler/CaO-$Al_2O_3-SiO_2$ (CAS) glass composites were investigated with a view to applying the composites to the substrate material in low temperature co-firing ceramic (LTCC) technology. The increased addition of $Al_2O_3$ filler with the particle size of 1 ${\mu}m$ monotonically decreased the density of the sintered specimen at a given temperature, while sintering of the 10 wt% $Al_2O_3$ added specimen at $925^{\circ}C$ for 2 h demonstrated 96.0 % of the relative density, dielectric constant of 6.34, and quality factor of 2,760 GHz. As for the influence of the particle size of the $Al_2O_3$ filler, there existed an optimum particle size (30 ${\mu}m$) to ensure successful densification (96.5 %) of the 10 wt% $Al_2O_3$/CAS composites at $925^{\circ}C$ for 2 h, at which condition the specimen demonstrated dielectric constant of 5.45 and quality factor of 3,740 GHz. When the influence of the sintering time of the 10 wt% $Al_2O_3$) (30 ${\mu}m$) added specimen was investigated at the sintering temperature of $925^{\circ}C$, an overly long sintering time degraded dielectric properties due to the over-sintering and the significant growth of the second phase such as anorthite, while the sintering for 4 h demonstrated 96.58 % of the relative density, dielectric constant of 5.4, and quality factor of 4,050 GHz. These results demonstrate the feasibility of the investigated material as the substrate material in LTCC technology.

• 전자공학회논문지SC
• /
• 제44권3호
• /
• pp.64-69
• /
• 2007

시스템의 자세 제어는 사용되는 모터의 위치 제어로 대응되며, 이러한 시스템은 운용환경 시에 충격 진동이 발생하게 된다. 이러한 충격 진동 외란을 제거해야 요구하는 위치 제어를 수행할 수 있다. 로봇 제어 분야에서 불확실한 외란에 의한 로봇의 자세 제어는 가장 기본적이면서 중요한 분야중의 하나이다. 이러한 문제를 다루기 위하여 계산 토크 방식에 기초한 선형 제어기법이나 적응 제어 기법, 강인 제어 기법 등을 이용한 연구 결과들이 발표되고 있다. 그러나 그러한 기법은 일반적으로 로봇의 정확한 동력학적 특성을 알아야 하며, 구현하기가 복잡하다. 따라서 본 논문에서는 적응 규칙에 의하여 모델의 불확실성, 시스템의 변화, 외란으로 인해 발생하는 공칭 플랜트와의 오차를 보상하도록 제어 입력을 생성하는 내부 루프 부분과 공칭 플랜트 모델의 명령을 추종하도록 하여 제어 입력을 생성하는 외부 루프 부분으로 구성되는 방법인 외란관측기(Disturbance OBserver : DOB) 제어 알고리즘을 제안한다. 또한 프로세서의 신뢰성과 수치 연산 및 알고리즘의 빠른 처리를 위해 현재 사용 빈도가 높은 TI사의 DSP시리즈 중에서 부동 소수점 연산 기능을 가지면서 모터 제어에 적합한 TMS320C2000계열의 TMS320F2812을 사용하여, 운용 시 발생되는 진동 등에 대한 외란 제거를 목적으로 한다. 본 논문은 규명된 시스템 모델식을 바탕으로 DOB 제어 시뮬레이션을 수행하고 시뮬레이션으로 검증된 DOB 모터 자세 제어 알고리즘을 DSP에 적용하기 위해 코드변환하고 PMSM 모터 모델 시뮬링크 블록을 구성하여 외란 관측기 제어 알고리즘을 모터 실험 시스템에 적용함으로써 타당성을 검증하고 상용 제어기로 실제 현장에 적용 가능함을 입증한다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 추계학술대회 논문집
• /
• pp.563-566
• /
• 2000

The effect of CuO and CuO-B $i_2$ $O_3$ additives on microwave dielectric properties of (P $b_{0.45}$C $a_{0.55}$)[F $e_{0.5}$N $b_{0.5}$)$_{0.9}$S $n_{0.1}$] $O_3$were investigated to decrease the sintering temperature for usage of Low Temperature Co-firing Ceramics (LTCC). The (P $b_{0.45}$C $a_{0.55}$)[F $e_{0.5}$N $b_{0.5}$)$_{0.9}$S $n_{0.1}$] $O_3$ceramics was sintered at 11$65^{\circ}C$. In order to decrease the sintering temperature, CuO and Cuo-B $i_2$ $O_3$ were added in the (Pb,Ca)[(Fe,Nb)Sn] $O_3$ with CuO-B $i_2$ $O_3$. For the addition of 0.4 wt.% CuO, the sintered density and the dielectric constant of the ceramics were revealed the maximum values of the 6.06g/c $m^2$ and 83 respectively and temperature coefficient of resonance frequency ($\tau$$_{f}$) shifted to the positive value. As increasing B $i_2$ $O_3$to the (Pb,Ca)[(Fe,Nb)Sn] $O_3$ with CuO-B $i_2$ $O_3$with 0.2 wt.% CuO, the sintered density, the $\varepsilon$$_{r}$ and the Q was decreased, and $\tau$$_{f}$ was minimized at 0.2 wt.% CuO, and 0.2 wt.% B $i_2$ $O_3$. For this composition, dielectric properties were $\varepsilon$$_{r}$ of 81, Q. $f_{0}$ of 4400 GHz, and $\tau$$_{f}$ of 5 ppm/$^{\circ}C$ at sintering temperature of 100$0^{\circ}C$. the relationship between the microstructure and properties of ceramics was studied by X-ray diffraction(XRD), scanning electron microscopy(SEM).copy(SEM).oscopy(SEM).copy(SEM).EM).

• 자원리싸이클링
• /
• 제21권6호
• /
• pp.12-22
• /
• 2012

본 연구는 제강용도로 사용하기 위해 돌로마이트를 하소후 남은 2 mm 이하의 경소백운석 부산물을 건축용 바닥 몰탈의 기존 팽창재로서 활용 가능성을 검토하고자 하였다. 경소백운석은 $600{\sim}800^{\circ}C$ 정도에서 하소하였을 때 반응성이 높은 준결정상태의 활성 마그네시아로 존재하게 되며, 이 활성화된 마그네시아는 수화초기 Brucite gel을 형성하여 수화물 비율을 상대적으로 줄여 치밀한 조직을 형성하는 원인으로 작용하고, 수화후기에는 결정질의 Brucite가 형성되어 수축 현상을 억제하며 부피가 2배 이상 팽창하여 화학적 수축균열 방지 역할을 하게 되는 것이다. 실험결과 경소백운석은 기존 사용 중인 팽창재 대비 동일량 적용시 압축강도는 우수하게 확인되었으나, 반응성은 기존 팽창재(생석회+무수석고)에 비해 다소 낮게 측정되었다. 하지만 팽창재로서의 역할은 충분한 것으로 확인되었으며, 공사기간 단축 등 부가적인 효과를 나타내었다.