• 한국초전도학회:학술대회논문집
• /
• v.16
• /
• pp.74-74
• /
• 2006

• 한국초전도학회:학술대회논문집
• /
• 2008.08a
• /
• pp.50-50
• /
• 2008

• 한국초전도학회:학술대회논문집
• /
• 2008.08a
• /
• pp.55-55
• /
• 2008

• Journal of the Korean Society of Combustion
• /
• v.21 no.3
• /
• pp.7-15
• /
• 2016

The fuel in conventional liquid fuel combustor is atomized by spray method for high efficiency and low emissions. To improve the overall fuel efficiency and lower pollutant emissions in liquid fuel combustion systems, the effective spatial and temporal separation of droplet evaporation from normal spray process is needed. In this paper, the recuperation of high temperature burnt gas for fuel evaporation was proposed to develop a cylindrical premixed combustor. The recuperation process using U shaped tube is effective to evaporate the liquid fuel. The results show that the flame mode is changed into red radiation flame, blue flame and lift off flame with decreasing equivalence ratio as gas fuel combustion mode. In particular, the blue flame is found to be very stable at heating load 9.2 kW and equivalence ratio 0.731. NOx was measured blow 105 ppm ($O_2$ zero base) from equivalence ratio 0.705 to 0.835. CO which is a very important emission index in liquid fuel combustor was observed below 5 ppm ($O_2$ zero base) under the same equivalence region.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.728-731
• /
• 2002

For the evaporation process, thickness uniformity is of great practical importance. And, it is commercially significant to improve the efficiency of material of the evaporant which is deposited on the substrate because of high price of organic materials. To achieve the better thickness uniformity and the higher evaporating efficiency, Samsung SDI has introduced the new concept of the asymmetric evaporation technology for depositing evener and cheaper organic layers. Based on the developed method, the uniformity of the organic layer thickness can be successfully controlled. Furthermore, the very high efficiency may allow the OLED displays be manufactured with the lower cost.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.10
• /
• pp.2273-2279
• /
• 2012

This research is based on fabricating Cu(In,Ga)$Se_2$ thin-film by co-evaporation method. On $1^{st}$ - stage, $In_2Se_3$ phase appeared when the substrate temperature reached to $400^{\circ}C$, however, there was small effect between the substrate temperature and absorbency spectrum on $2^{nd}$, $3^{rd}$ - stage because the average thickness of the thin-film was $1{\mu}m$ or higher. SEM and XRD was measured on $2^{nd}$ and $3^{rd}$ stage and it showed as the substrate temperature increases, the density of the crystal structure increased with the decreament of the vacancy. Furthermore, the formation of Cu(In0.7Ga0.3)$Se_2$ phase showed at $480^{\circ}C$ and $500^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.04a
• /
• pp.39-42
• /
• 2004

The $Bi_2Sr_2Ca_nCu_{n+1}O_x$ superconducting thin film fabricated by using the sputtering method was compared with the $Bi_2Sr_2Ca_nCu_{n+1}O_x$ superconducting thin film fabricated by using the evaporation method. In doing the ultra-low deposition because each element can exist on the substrate surface, both the sputtering method and the evaporation method could easily fabricate single phase of the Bi2212 phase. Also, it is cofirmed that by optimizing the deposition condition, each single phase of the Bi2201 phase and the Bi2212 phase can be fabricated, the sticking coefficient of Bi element is clearly related to the changing of substrate temperature and the formation of the Bi2212 phase.

• Macromolecular Research
• /
• v.16 no.8
• /
• pp.717-724
• /
• 2008

In this study, we prepared all-trans retinoic acid (ATRA)-encapsulated, surfactant-free, PLGA nanoparticles. The nanoparticles were formed by nanoprecipitation process, after which the solvent was removed by solvent evaporation or dialysis method. When a nanoparticle was prepared by the nanoprecipitation - solvent evaporation method, the nanoparticles were bigger than the nanoparticles of the nanoprecipitation - dialysis method, despite the higher although loading efficiency. Nanoparticles from the nanoprecipitation - dialysis method were smaller than 200 nm in diameter, while the loading efficiency was not significantly changed. Especially, nanoparticles prepared from DMAc, 1,4-dioxane, and DMF had a diameter of less than 100 nm. In the transmission electron microscopy (TEM) observations, all of the nanoparticles showed spherical shapes. The loading efficiency of ATRA was higher than 90% (w/w) at all formulations with exception of THF. The drug content was increased with increasing drug-feeding amount while the loading efficiency was decreased. In the drug release study, an initial burst was observed for $2{\sim}6$ days according to the variations of the formulation, after which the drug was continuously released over one month. Nanoparticles from the nanoprecipitation - dialysis method showed faster drug release than those from the nanoprecipitation - solvent evaporation method. The decreased drug release kinetics was observed at lower drug contents. In the tumor cell cytotoxicity test, ATRA-encapsulated, surfactant-free, PLGA nanoparticles exhibited similar cytotoxicity with that of ATRA itself.

• Progress in Superconductivity and Cryogenics
• /
• v.9 no.1
• /
• pp.5-8
• /
• 2007

We have investigated the superconducting properties and surface morphology of $Sm_xBa_yCu_3O_{6+z}$ thin films deposited on LMO/IBAD-MgO/Hastelloy which prepared with different composition ratio by co-evaporation method(EDDC, Evaporation using Drum in Dual Chambers). We observed the composition ratio of SmBCO thin films by EDS analysis. We fabricated SmBCO thin film with critical current density of $1.5{\times}10^6A/cm^2$ at composition ratio of SM:Ba:Cu=1.10:2.01:3(at 77 K self-field). And, we confirmed that substitution of Sm-Ba did not occur at Cu rich phase by EDS analysis.

• YAKHAK HOEJI
• /
• v.44 no.6
• /
• pp.511-520
• /
• 2000

Various bupivacaine-loaded microspheres were prepared from poly (d,l-lactide) (PLA) or poly (d,l-lactic-co-glycolide) (PLGA) by a solvent evaporation method for the sustained release of drug. PLA and PLGA microspheres were prepared by w/o/w and w/o/o multiple emulsion solvent evaporation, respectively. The effects of process conditions such as emulsification speed, emulsifier type, emulsifier concentration and internal/external phase ratio on the characteristics of microspheres were investigated. The prepared microspheres were characterized for their drug loading, size distribution, surface morphology and release kinetics. Drug loading efficiency was higher in the microspheres prepared by w/o/o multiple emulsion than that by w/o/w multiple emulsion method, because the solubility of bupivacaine HCI was decreased in oil phase compared with water phase. The prepared microspheres had an average diameter between 1 and $2\;{\mu}M$ in all conditions of two methods. In morphology studies the PLA microspheres showed an irregular shape and smooth surface, but PLGA microspheres had a spherical shape and smooth surface. The release pattern of the drug from microspheres was evaluated on the basis of the burst effect and the extent of the release after 24h. The in vitro release of bupivacaine HCl from microspheres showed a large initial burst release and $60{\sim}80%$ release within one day in all conditions of two methods. The extents of the burst release against PLA and PLGA microspheres were $30{\sim}50%$ and $50{\sim}80%$ within 20min, respectively. This burst release seems to be due to the smaller size of microspheres and the solubility of drug in water.