• 대한기계학회논문집
• /
• 제19권2호
• /
• pp.402-407
• /
• 1995

The effects of room temperature and strain aging treatment are discussed on the critical condition for the onset of growth of non-propagating cracks on 0.15% C low carbon steel, with special emphasis on the length of the critical non-propagating crack and on the crack opening displacement(COD) at the crack tip. It is found from the experimental analysis that room temperature and strain aging of a fatigue pre-cracked specimen introduced the closure of a crack tip of the pre-crack and the reduction of crack opening displacement at the wake of crack, together with an improvement in crack growth resistance of the microstructure. This may cause an increase in the endurance limit of the specimen, through the enhancement of effective stress for the onset of growth of the critical non-propagating crack.

• 동력기계공학회지
• /
• 제4권4호
• /
• pp.41-47
• /
• 2000

Fatigue crack propagation rate and threshold characteristics of the SA516/70 steel which is used for the low temperature pressure vessels, were studied in the room temperature of $25^{\circ}C$ and low temperature ranges of $-10^{\circ}C,\;-30^{\circ}C,\;-60^{\circ}C\;and\;-80^{\circ}C$ with stress ratio of R=0.1. In the logarithmic relationship between the fatigue crack propagation rate($d{\alpha}/dN$) and stress intensity factor range ${\Delta}K$, the linear relationship was obtained up to $d{\alpha}/dN=4.425{\times}10^4mm/cycle$ in the same of room temperature, but in low temperature case, the relationship was extended to the range of low crack propagation rate. The fractured specimens were examined by SEM. Tested results showed that specimen failed at low temperature exhibit the quasi-cleavage fracture formation however considerable ductility proceed final fracture.

• 한국산림과학회지
• /
• 제112권4호
• /
• pp.544-553
• /
• 2023

활엽수림은 여름철에 착엽을 통해 일사를 차단하여 열 스트레스를 완화하는 역할을 하는 것으로 알려져 있지만, 이와 관련된 데이터의 축적은 부족한 실정이다. 따라서 본 연구는 여름철 활엽수림에서의 휴식이 온열환경 쾌적성 및 인체의 생리・심리적 반응에 미치는 영향을 분석하는 것을 목적으로 하였다. 연구대상자는 남녀 대학생 32명(21.5±2.1세)으로 하였다. 연구대상자는 두 명이 한 조를 이루어 각각 실험지(수관울폐도: 76.6%)와 대조실험지(25.9%)로 이동하였고, 일련의 실험과정을 이후 장소를 교대하여 같은 실험을 진행하였다. 실험과정은 다음과 같다. 연구대상자는 의자에 앉아 휴식한 후, 눈을 감고 5분 동안 안정을 취하였다. 이때의 온열환경 쾌적성을 평가하고 심박변이도, 심박수, 이마체온을 연속적으로 측정하였다. 이후 혈압 및 맥박수를 측정하였으며, 주관평가를 진행하였다. 그 결과, 실험지는 통계적으로 유의미한 예상평균한서감지수 및 예상불만족률의 감소, 부교감신경활동의 증가, 심박수・이마체온・이완기혈압・맥박수의 감소가 나타났으며, 주관적 온열감 및 쾌적감이 개선되었다. 결론적으로, 수관울폐도가 높은 활엽수림은 여름철 온열 스트레스를 감소시키며, 인체를 생리・심리적으로 안정시킨다는 것을 확인하였다.

• 한국해양학회지:바다
• /
• 제18권3호
• /
• pp.111-121
• /
• 2013

지역규모의 정확한 일기예보와 해양생태계 변화 이해에 있어서 수온 예측은 매우 중요하다. 황해는 조류가 매우 빠르고 탁도가 높다. 이러한 해역에서는 수치 모델의 수직 혼합 기법 및 해수의 탁도에 따른 수형(water type)이 수온 구조 결정에 많은 영향을 미친다. 수직 혼합 기법 변화와 탁도의 변화에 따른 황해 수온 모사의 민감도를 알아보기 위해 3차원 해양 순환 모델인 Regional Ocean Modeling System (ROMS)을 사용하여 수치 실험을 수행하였다. 수직 혼합 기법은 해양 순환 모델에서 많이 사용되는 Mellor-Yamada level 2.5 closure(M-Y)와 K-Profile parameterization (KPP)을 사용하고, 탁도는 Jerlov의 분류에 따른 수형 1, 3, 5를 사용하여 수치 실험을 수행하고 그 결과를 국립수산과학원에서 제공하는 정선 해양 관측 자료와 비교, 분석하였다. M-Y 기법은 수직적 혼합을 상대적으로 강하게 모의하였으며 그 결과로 저층수온이 높게 형성되었다. 높은 저층 수온은 탁도를 높게 설정하면 완화되지만 표층 수온이 높아지는 단점이 있다. KPP 기법은 M-Y 기법보다는 수직 혼합을 약하게 모의하고 이 약한 수직 혼합 때문에 황해 연안을 따라 형성되는 조석전선을 잘 재현하지 못하였으나, 저층 수온은 관측 수온에 더 가깝게 재현하였다. 결과적으로 황해 3차원 해양순환 모델실험에서 M-Y 기법은 수직 혼합이 잘 되어 표층과 저층의 수온 차이가 작게 나타나고, KPP 기법은 이와 반대로 모의하였다. 탁도의 영향을 표현하는 Jerlov 수형은 높을수록 일사량이 낮은 수심까지만 투과되어 성층을 잘 표현하였고, 낮을수록 깊은 수심까지 일사량이 투과되어 표층과 저층의 수온차를 작게 모의하였다.

• Composites Research
• /
• 제25권4호
• /
• pp.117-125
• /
• 2012

필름 삽입 사출 시편의 휨은 비대칭적인 잔류응력 분포에 기인한다. 비대칭적 잔류응력과 온도 분포는 삽입된 필름 표면의 수직방향으로 지연되는 열 전달에 의해 발생한다. 사출 공정조건 최적화를 통해 필름 삽입 사출 시편의 휨을 억제할 수 없었기 때문에, 필름 삽입 사출 시편의 휨을 최소화하기 위해서 유리 섬유가 강화된 복합재료를 기판으로 사용하였다. 유리 단섬유의 분포를 마이크로 CT 장비를 이용하여 평가하였다. 복합재료로 구성된 기판을 이용한 필름 삽입 사출 시편의 배향 텐서와 휨을 계산하기 위해서는 적절한 마이크로 역학, 이방적 열팽창계수 및 닫힌 어림법 모델이 선택되어야만 한다. 여섯 종류의 마이크로 역학모델, 세 종류의 열 팽창 계수 모델 및 다섯 종류의 닫힌 어림법 모델을 고려한 후, Mori-Tanaka 모델, Rosen and Hashin 모델 및 third orthotropic 닫힌 어림법 모델을 선택하였다. 수치적으로 계산된 섬유 배향 텐서와 휨에 관한 결과들은 실험결과와 잘 일치하였고, 유리 섬유의 보강효과가 필름 삽입 사출 복합 재료 시편의 휨에 미치는 영향을 파악하였다.

• 소성∙가공
• /
• 제22권8호
• /
• pp.463-469
• /
• 2013

In the previous work, a new forging process design, which included incremental upsetting, diffusion bonding and cogging, was suggested as a method to manufacture 1.9wt%C ultrahigh carbon workrolls. The previous study showed that incremental upsetting and diffusion bonding are effective in closing voids and healing of the closed void. In addition, compression tests of the 1.9wt%C ultrahigh carbon steel revealed that new microvoids form within the blocky cementite at temperatures of less than $900^{\circ}C$ and that local melting can occur at temperatures over $1120^{\circ}C$. Thus, the forging temperature should be controlled between 900 and $1120^{\circ}C$. Based on these results, incremental upsetting and diffusion bonding were used to check whether they are effective in closing and healing voids in a 1.9wt%C ultrahigh carbon steel. The incremental upsetting and diffusion bonding were performed using sub-sized specimens of 1.9wt%C ultrahigh carbon steel. The specimen was deformed only in the radial direction during the incremental upsetting until the reduction ratio reached about 45~50%. After deformation the specimens were kept at $1100^{\circ}C$ for the 1 hour in order to obtain a high bonding strength for the closed void. Finally, microstructural observations and tensile tests were conducted to investigate void closure behavior and bonding strength.

• Journal of Advanced Marine Engineering and Technology
• /
• 제25권5호
• /
• pp.1108-1114
• /
• 2001

The fatigue crack propagation behavior of the SA516-Grade 70 steel which is used for pressure vessels was experimentally examined under the condition of at room temperature, $150^{\circ}C$, $250^{\circ}C$ and $370^{\circ}C$ with stress ration of R=0.1 and 0.3. The fatigue crack propagation rate , da/dN, related with the stress intensity factor range, $\vartriangle$N, was influenced by the stress ration within the stable growth of fatigue crack(Region II) with an increase in $\vartriangle$N. The resistance to the fatigue crack growth at high temperature is higher in comparison with that at room temperature, and the resistance attributed to the extent of plasticity-induced by compressive residual stress according to the cyclic loads. Fractographic examinations revels that the differences of the fatigue crack growth characteristics between room and high temperatures are mainly explained by the crack and oxide-induced by high temperature.

• Ocean and Polar Research
• /
• 제29권3호
• /
• pp.217-231
• /
• 2007

To explore limiting factors of spring bloom caused by waste disposal after dumping activity commenced in the Yellow Sea, we used a 1-dimensional temperature-ecological coupled model. The vertical structure of temperature and vertical diffusivity (Kh) are calculated by the temperature model with sea surface temperature using the 2.5 layers turbulence closure scheme. The ecological model applied results at the temperature model consisted of five state variables (DIN, DIP, phytoplankton, zooplankton, and detritus) forced by photosynthetically available radiation. We simulate year-to-year variations of plankton and nutrients using the coupled model from 1998 to 2000 and compare results of the model with observed data. It turned out that temperature is the growth factor of spring bloom in dumping area. During the winter the weak stratification made sufficient supply of the accumulated nutrients from the sea bed into the upper water column and led to the bloom in the coming spring. Radiation also turned out to be another important factor of spring bloom in the study area. Insufficient radiation of March 1999 showed low chlorophyll-a concentration despite sufficient nutrients in the surface.

• 한국해양공학회지
• /
• 제14권1호
• /
• pp.23-28
• /
• 2000

The fatigue crack growth behavior of the cold-rolled STS 304 steel developed for membrane material of LNG storage tank was examined experimentally at 293K, 153K and 111K. The fatigue crack growth rate(do/dN) tends to increase as the stress ratio (R) increases over the testing temperature when compared at the same stress intensity factor range($\Delta$K). The effect of R on do/dN is more explicit at low temperatures than at room temperature. The resistance of fatigue crack growth at low temperatures is higher compared with that at room temperature which is attributed to the extent of strain-induced martensitic transformation at the crack tip. The temperature dependence of fatigue crack growth resistance is gradually vanished with an increase in $\Delta$K which correlates with a decreasing fracture toughness with decreasing temperature. Fractographic examinations reveal that the differences of the fatigue crack growth characteristics between room and low temperature are mainly explained by the crack closure and the strengthening due to the martensitic transformation.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 추계학술대회 논문집
• /
• pp.359-365
• /
• 2002

The fatigue crack growth behavior of the SA516/60 steel which is used for pressure vessels was examined experimentally at room temperature $25^{\circ}C,\;-30^{\circ}C,\;-60^{\circ}C,\;-80^{\circ}C,\;-100^{\circ}C$ and $-120^{\circ}C$ with stress ratio of R=0.05, 0.1 and 0.3. Fatigue crack propagation rate da/dN related with stress intensity factor range ${\Delta}K$ was influenced by stress ratio in stable of fatigue crack growth (Region II) with an increase in ${\Delta}K$. The resistance of fatigue crack growth at low temperature is higher compared with that at room temperature, which is attributed to tile extent of plasticity-induced by compressive residual stress according to the cyclic loads. Fractographic examinations reveal that the differences of the fatigue crack growth characteristics between room and low temperatures are mainly explained by the crack closure and the strengthening due to the plasticity induced and roughness induced.