• Journal of Embryo Transfer
• /
• v.20 no.3
• /
• pp.233-238
• /
• 2005

This study was carried out to investigate effects of claw trimming on reproductive efficiency in lactating cow. The results obtained were summarized as follows: 1. Days to 1st postpartum service were 180.9$\pm$47.2 days for control and 111.9$\pm$17.1 days for claw trimming. 2. Conception rate by 1st postpartum service was $25.0\%$ for control and $66.7\%$ for claw trimming. 3. Days to 1st postpartum conception were 258.1$\pm$43.3 days for control and 151.6$\pm$26.2 days for claw trimming(p<0.05). 4. Services per conception were 1.88$\pm$0.23 times for control and 1.44$\pm$0.18 times for claw trimming. 5. Calving interval was 489.3$\pm$47.2 days for control and 430.8$\pm$26.2 days for claw trimming.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.5
• /
• pp.745-752
• /
• 2012

Transverse flux machine (TFM) has been proved to be very suitable for high-torque, low-speed, and direct-drive situation in industry. But the complex structures and costly permanent magnets (PMs) are two key limitations of its wide range of applications. This paper proposes a new claw pole TFM (ACPTFM) which features an assembled claw pole stator and using the lamination steels material to overcome the complex structures. By combining response surface methodology (RSM) with design of experiment, an optimum design method is put forward to improve the PM's contribution to the torque in order to save the PM's amount. The optimum design results demonstrate the validity of the proposed optimum design method and the optimized model. Eventually, the finite-element analysis (FEA) calculation method, which is used in the optimization process, is verified by the experiments in a prototype.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.1 no.3
• /
• pp.321-329
• /
• 2012

Providing variable load for testing a motor in high speed conditions is usually a difficult task. The eddy current brake can be used in application of load testing of motors. This paper deals with construction of a novel claw pole eddy current brake which is employed as a load for a DC counter rotating motor (CRM). These kinds of motors have two inner and outer shafts that rotate in opposite directions simultaneously, which are particularly suitable for under water propulsion systems. The prototype 45KW eddy current brake consists of two parts. One of them is installed on the inner shaft of the 60KW DC CRM and the other one is installed on its outer shaft. The simulation and experimental results with prototype brakes are also analyzed by using MATLAB/Simulink and the operational characteristic of the brake is demonstrated as a function of the motor speed and current of the magnetic poles.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.10
• /
• pp.1942-1946
• /
• 2009

This paper presents a shape design process of Claw-Poles Stepping Motor(CPSM) using Modified Magnetic Equivalent Circuit Method(MMEC). Because this motor is adopted on low power devices, the motor size is a very small type. But it have a very strong permanent magnet. So magnetic saturation effect happens on yoke teeth of CPSM. Also this magnetic saturation effect causes more leakage flux component between yoke tooth have another pole. In this motor type, it is essential to design a shape of yoke teeth for avoiding the magnetic saturation effect and the leakage flux. In this paper, MMEC including the magnetic saturation effect and the leakage flux component was used for design process. Comparing with data calculated by using the MMEC and results analyzed by 3-D FEM, it could be stated that the design process with MMEC was reasonable. Finally, the model has the optimized shape of yoke teeth was compared with a conventional model for no-load Back EMF and torque at steady-state operation.

• Animal Systematics, Evolution and Diversity
• /
• v.36 no.4
• /
• pp.285-295
• /
• 2020

Adults of Prosimulium kiotoense and Twinnia japonensis were collected and reported from Korea for the first time. Since adult black flies are notorious for morphological homogeneity particularly in female, larval and pupal characters have been mainly used to identify them. Adults of P. kiotoense can be identified by the following combination of characteristics: Adult, wing with radial sector (Rs) branched into R²⁺³ and R⁴⁺⁵; hind leg basitarsus without calcipala; first tarsomere without pedisulcus. Female, claw without basal thumblike lobe; hypogenial valve elongate, convex, heavily sclerotized medially, posterior end touching each other, space between valves rhomboid. Male, claw with basal thumblike lobe; ventral plate keel shaped; gonostylus with 2-3 spinules. Adults and pupa of T. japonensis can be identified by the following combination of characteristics: Adult, antenna with 7 flagellomeres. Female, hypogenial valve broad, posterior end of valve not touching each other; cercus elongate, subquadrate; spermatheca slightly wider and long, round. Male, claw with basal thumblike lobe; gonostylus with 1 spinule; ventral plate flat. Pupa, gill of 16 filaments, arising from 3 swollen stalks; abdominal tergites without spine combs except tergites III and IV with small recurved hooks; terminal spine well developed, wavy shaped.

• Journal of Korean Foot and Ankle Society
• /
• v.16 no.1
• /
• pp.47-52
• /
• 2012

Purpose: The purpose of this study is to evaluate the effect of axial shortening metatarsal osteotomy on the treatment of advanced rheumatoid arthritis patients with severe hallux valgus and claw toe deformity of lesser toes which is used for preserving the metatarsophalangeal joint. Materials and Methods: From January 2005 to June 2009, 18 cases of axial shortening metatarsal osteotomy in advanced rheumatoid arthritis were reviewed ; all of them followed up for more than 2 years after surgical procedures and the mean follow up period was 3.4 years. We performed axial shortening Scarf osteotomy and Akin osteotomy for hallux valgus and Weil osteotomy with soft tissue release for claw toe of lesser toes, respectively. We measured preoperative and postoperative hallux valgus angle, each metatarsal shortening length and the range of motion of the metatarsophalangeal joints through radiographic and clinical examination and compared them each other. Clinical results were evaluated by American Orthopedic Foot and Ankle Society (AOFAS) score and subjective satisfaction of the patients. Results: The hallux valgus angle was reduced from the preoperative mean value of 44.8 degree to 9.0 degree postoperatively and the range of motion of the metatarsophalangeal joint of great toe and lesser toes was increased from the mean of 21.7 degree and 11.0 degree preoperatively to 38.0 degree and 32.5 degree, respectively at postoperation. Also, the mean AOFAS score was improved from 26.5 points to 67.4 points. Conclusion: Axial shortening osteotomy is a useful method to correct the deformity and preserve the metatarsophalangeal joint for severe hallux valgus and claw toe deformity in advanced rheumatoid arthritis.

• Journal of Embryo Transfer
• /
• v.21 no.1
• /
• pp.45-51
• /
• 2006

This study was carried out to investigate effect of claw trimming on milk yield and its composition in Holstein at different lactation stages. 1 . There was no difference in daily milk yield between control and claw trimming in early, mid and late lactating Holsteins. 2. Somatic cell count (SCC) was lower in early lactation and it was higher in late lactation when claws were trimmed in Holstein. However, claw trimming did not affect SCC during mid lactation in Holstein. 3. Milk fat, protein and total solids were decreased during late lactation in Holstein after claw trimming. However, milk composition was not affected by claw trimming in early and mid lactating Holsteins.

• Journal of Animal Environmental Science
• /
• v.12 no.3
• /
• pp.107-114
• /
• 2006

This study was carried out to investigate the effect of new foot-bath facility and detergent solution (sodium molylbdenate, citrate, potassium nitrate, tataric acid, sodium hypo-cholorite, and zinc sulfate) on claw health in lactating dairy cows. Minimal inhibition concentration (MIC) and minimal bactericidal concentration (MBC) of copper sulphate were 0.31% for E. coli and Bacillus isolated from cows claw. The MIC and MBC of new detergent for E. coli were 1.25% and 5%, respectively, however their respectively values for Bacillus were noticed 0.63% and 2.5%. Both 5E. coli and Bacillus populations in petri-dishes were significantly reduced (more than 95%) with the application of new detergent solution (5% or 16%). Locomotion score (LS 1-5; very good to severely bad) of lactating cows were significantly improved with in 30 days with the use of new detergent solution in foot bath. The LS2 (n=16), LS3 (n=16), and LS4 (n=7) were shown 100%, 43.8%, and 14.3% recovery rate within 30 days with the use of new detergent solution. However, LS5 (n=2) were not recovered to normal claw health and locomotion score within 30 days of new detergent application. Usage of new detergent solution for 60 days in a foot bath have shown 81.3%, 71.4% and 50.0% recovery rate in cows with LS3, LS4 and LS5, respectively. Abnormal claw incidence was reduced from 18.8% to 1.5% in overall herd (n=80) with the use of new detergent solution (16%) in a foot bath for 90 days. In conclusion, usage of 16% of our detergent solution for 60 days in a foot bath can significantly improve the cow claw health and thus mitigate the negative effects of abnormal claw on productivity of cows and dairy farm income.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.02a
• /
• pp.31-31
• /
• 1999

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.670_671
• /
• 2009

This paper presents a optimum design process for static torque characteristics of the Claw-Poles PM Stepping Motor(CPSM). Since the shape of CPSM changes along with axial direction, CPSM should only be analyzed by 3D-FEM. But 3D-FEM needs too much computation time and computer resources. Therefore, it is essential to reduce the number of 3D-FEM analysis models. In this paper, two design factors which affect the static torque characteristics of CPSM were selected. Optimum design process was able to make progress by using Pattern Search Algorithm and 3D-FEM. Finally, optimized model was compared with a conventional model.