• 대한토목학회논문집
• /
• 제26권1A호
• /
• pp.117-132
• /
• 2006

3변 고정 1변 자유 직사각형 얇은 판에 대한 기존 해석해를 무차원식으로 유도하고 특성을 분석하였다. Timoshenko와 Woinowsky-Krieger의 방법(1959)은 변장비가 1보다 작은 경우에만 제한적으로 해가 존재하여 처짐 특성에 대한 실용적인 해가 되지 않음을 밝혔다. 굴정(堀井)와 본(本)의 방법(1968)에 수치안정을 위한 항을 추가하여 최대 150개 항까지 구성된 급수해를 구하였고 이로부터 계산한 휨 모멘트의 수렴을 분석하였다. 수정 굴정(堀井)와 본(本)의 방법은 모든 변장비에 대한 처짐 특성을 구할 수 있으나 고정단과 자유단이 접하는 교차점에서의 모멘트 계산은 자유단 경계조건을 만족하지 않으며 그 원인을 분석하였다.

• 한국해양공학회지
• /
• 제33권6호
• /
• pp.535-546
• /
• 2019

The paper presents a closed-form analytical solution for the ultimate strength of sandwich panels with metal faces and an elastic isotropic core during combined in-plane compression and lateral pressure under clamped boundary condition. By using the principle of minimum potential energy, the stress distribution in the faces during uni-axial edge compression and constant lateral pressure was obtained. Then, the ultimate edge compression was derived on the basis that collapse occurs when yield has spread from the mid-length of the sides of the face plates to the center of the convex face plates. The results were validated by nonlinear finite element analysis. Because the solution is analytical and closed-form, it is rapid and efficient and is well-suited for use in practical structural design methods, including repetitive use in structural optimization. The solution applies for any elastic isotropic core material, but the application that stimulated this study was an elastomer-cored steel sandwich panel that had excellent energy absorbing and protective properties against fire, collisions, ballistic projectiles, and explosions.

• 대한조선학회지
• /
• 제17권4호
• /
• pp.1-11
• /
• 1980

Stiffened plates are commonly used as a component of ship's structures. Most frequently symmetrically stiffened plates are used, but some of stern structures and any specified parts are often constructed with eccentrically stiffened plates. The problems of these eccentrically stiffened plates have been studied rarely, and the results of eccentricity effect of eccentrically stiffened plates are not available. This paper deals with the analysis of eccentrically stiffened plates in the linear elastic range. The derivation of the stiffness matrix was carried out by finite element method for which the isoparametric element was adopted. To show the effect of eccentricity, the deflection at the center under the uniformly distributed and the concentrated load of simply supported and clamped plate models are computed respectively in accordance with the eccentricity of the stiffener. As shown in the results of computations, the eccentricity effect of concentrated load case is greater than that of distributed load case and that of simply supported boundary condition is greater than that of clamped boundary condition. The higher eccentricity of stiffener is, the smaller the effect of stiffener becomes, therefore scantling of eccentrically stiffened plates should be considerably greater than those of symmetrically stiffened plates.

• Structural Engineering and Mechanics
• /
• 제33권1호
• /
• pp.15-30
• /
• 2009

In this study, the nonlinear vibrations of stepped beams having different boundary conditions were investigated. The equations of motions were obtained by using Hamilton's principle and made non dimensional. The stretching effect induced non-linear terms to the equations. Natural frequencies are calculated for different boundary conditions, stepped ratios and stepped locations by Newton-Raphson Method. The corresponding nonlinear correction coefficients are also calculated for the fundamental mode. At the second part, an alternative method is produced for the analysis. The calculated natural frequencies and nonlinear corrections are used for training an artificial neural network (ANN) program which has a multi-layer, feed-forward, back-propagation algorithm. The results of the algorithm produce errors less than 2.5% for linear case and 10.12% for nonlinear case. The errors are much lower for most cases except clamped-clamped end condition. By employing the ANN algorithm, the natural frequencies and nonlinear corrections are easily calculated by little errors, and the computational time is drastically reduced compared with the conventional numerical techniques.

• Structural Engineering and Mechanics
• /
• 제12권2호
• /
• pp.189-200
• /
• 2001

This paper presents an experimental modal analysis of perforated rectangular plates in air or in contact with water. The penetration of holes in the plates had a triangular pattern with P/D (pitch to diameter) 2.125, 2.500, 3.000 and 3.750. The plate was clamped along the plate edges by a number of bolts and nuts. The natural frequencies of the perforated plates in air were obtained by the analytical method based on the relation between the reference kinetic and maximum potential energies and compared with the experimental results. Good agreement between the results was found for the natural frequencies of the perforated plates in air. Additionally, it was empirically found that the natural frequencies of the perforated plate in air increase with an increase of P/D, on the other hand, the natural frequencies of the perforated plate in contact with water decrease with an increase of P/D.

• Structural Engineering and Mechanics
• /
• 제18권3호
• /
• pp.303-314
• /
• 2004

An artificial neural network (ANN) application is presented for flexural and axial vibration analysis of elastic beams with various support conditions. The first three natural frequencies of beams are obtained using multi layer neural network based back-propagation error learning algorithm. The natural frequencies of beams are calculated for six different boundary conditions via direct solution of governing differential equations of beams and Rayleigh's approximate method. The training of the network has been made using these data only flexural vibration case. The trained neural network, however, had been tested for cantilever beam (C-F), and both end free (F-F) in case the axial vibration, and clamped-clamped (C-C), and Guided-Pinned (G-P) support condition in case the flexural vibrations which were not included in the training set. The results found by using artificial neural network are sufficiently close to the theoretical results. It has been demonstrated that the artificial neural network approach applied in this study is highly successful for the purposes of free vibration analysis of elastic beams.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.840-843
• /
• 2005

For an analysis of nonlinear dynamic behavior in carbon nanotube(CNT) an electrostatic force of CNT was investigated. The boundary condition in the CNT was assumed to clamped-clamped case at both ends. This type of CNT is widely used as micro and nano-sensors. For larger gaps in between sensor and electrode the van der Waals force can be ignored. The electrostatic force can be expressed as linear form using Taylor series. However, the first term of the series expansion was investigated here. The electrostatic force From this study we can conclude that for larger gaps the electrostatic force play an important role in determining the deflections as well as the pull-in voltage of simply supported switches.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.388-392
• /
• 1995

The Electronic Speckle Pattern Interferometry(ESPI) has been applied to many technical problems such as deformation and displacement measurement, strain visualization and surface roughness monitoring. Composite materials have various complicated characteristics depending on the ply materials,ply orientations,ply stacking sequences and boundary conditions. Therefore, it is difficult to analyze composite material. For efficient use of composit materials in engineering applications, the dynamic behavior such as, natural frequencies and modal patterns should be identified. This studying presents FEM results for the free vibration of symmetrically laminated composite as [30/-30/90] $_{s}$. The natural frequencies of laminated composite rectangular plates having the boundary condition(:2-edge clamped) are experimentally obtained. In order to demonstrate the validity of the experiment,FEM analysis using ANSYS was performed and natural frequencies experimentally obtained is compared with calculated by FEM analysis. The results obtained from both experiment and FEM analysis show a good agreement.t.

• 한국정밀공학회지
• /
• 제20권5호
• /
• pp.132-139
• /
• 2003

In this study, it is attempted to obtain the optimum size of holes in 15 square plate models where a hole exists on every quadrant of a plate, and to get eigenvalues by performing free vibration analysis for each model. Moreover, the specimen is produced from optimized square plate and eigenvalue of each plate is measured through the shocking load. And then the result is compared with that of finite element analysis. For free vibration analysis of the square plate, the boundary condition of finite element analysis and experiment is assumed as both ends clamped support. From the results of this study, it is known that more stable structures can be designed by changing the natural frequency which is dependent on the location of holes and further studies are considered to be necessary fur the basic design information.

• Smart Structures and Systems
• /
• 제22권3호
• /
• pp.327-334
• /
• 2018

In this paper, dynamic buckling of the smart subjected to blast load subjected to electric field is studied. The sandwich structure is rested on Pasternak foundation with springs and shear elements. Applying piezoelasticity theory and hyperbolic shear deformation beam theory (HSDBT), the motion equations are derived by energy method. For calculating the dynamic instability region (DIR) of the sandwich structure, differential quadrature method (DQM) along with Bolotin method is used. The aim of this study is to investigate the effects of applied voltage, geometrical parameters of structure and boundary conditions on the DIR of the structure. The results show that applying negative voltage, the DIR will be happened at higher excitation frequencies. In addition, the clamped-clamped beam leads to higher excitation frequency with respect to simply supported boundary condition.