• Journal of Positioning, Navigation, and Timing
• /
• 제4권4호
• /
• pp.151-160
• /
• 2015

GPS L2C signal is a recently added civil signal to L2 frequency and is constructed by time division multiplexing of civil moderate (L2-CM) and civil long (L2-CL) code signals. While the L2-CM code is 20 ms-periodic and modulates satellite navigation message, the L2-CL code is 1.5s-periodic with 767,250 chips long code sequence and carries no data. Therefore, the L2-CL code signal allows receivers to perform a very long coherent integration. However, due to the length of the L2-CL code, the acquisition of the L2-CL code signal may take too long or require too much hardware resources. In this paper, we propose a three-step ultra-fast L2-CL code acquisition (TSCLA) technique for dual band GPS receivers. In the proposed TSCLA technique, a dual band GPS receiver sequentially acquires the coarse/acquisition (C/A) code signal at L1 frequency, the L2-CM code signal, and the L2-CL code signal to minimize mean acquisition time (MAT). The theoretical performance analysis and numerous Monte Carlo simulations show the significant advantage of the proposed TSCLA technique over conventional techniques introduced in the literature.

• Computers and Concrete
• /
• 제28권5호
• /
• pp.487-495
• /
• 2021

The use of prestressed concrete box girder bridges built by segmentally balanced cantilevers has bloomed in the last decades due to its significant structural and construction advantages in complex topographies. In Colombia, this typology is the most common solution for structures with spans ranging of 80-200 m. Despite its popularity, excessive deflections in bridges worldwide evidenced that time-dependent effects were underestimated. This problem has led to the constant updating of the creep and shrinkage models in international code standards. Differences observed between design processes of box girder bridges of the Colombian code and Eurocode, led to the need for a validation of in-service status of these structures. This study analyzes the long-term behavior of the Tablazo bridge with data scarcity. The measured leveling of this structure is compared with a finite-element model that consider the most widely used creep and shrinkage models in the literature. Finally, an adjusted model evidence excessive deflection on the bridge after six years. Monitoring of this bridge typology in Colombia and updating of the current design code is recommended.

• Wind and Structures
• /
• 제15권3호
• /
• pp.209-221
• /
• 2012

The flutter reliability analysis of long span bridges requires use of a software tool that predicts the uncertainty in a flutter response due to uncertainties in the model formulation and input parameters. Existing flutter analysis numerical codes are not capable of dealing with stochastic uncertainty in the analysis of long span bridges. The goal of the present work is to develop a software tool (FREASB) to enable designers to efficiently and accurately conduct flutter reliability analysis of long span bridges. The FREASB interfaces an open-source Matlab toolbox for structural reliability analysis (FERUM) with a typical deterministic flutter analysis code. The paper presents a brief introduction to the generalized first-order reliability method implemented in FREASB and key steps involved in coupling it with a typical deterministic flutter analysis code. A numerical example concerning flutter reliability analysis of a long span suspension bridge with a main span of 1385 m is presented to demonstrate the application and effectiveness of the methodology and the software.

• Structural Engineering and Mechanics
• /
• 제8권6호
• /
• pp.531-546
• /
• 1999

The paper presents an experimental and theoretical study on the influence of steel fibers and longitudinal tension and compression reinforcements on immediate and long-term deflections of high-strength concrete beams of 85 MPa (12,300 psi) compressive, strength. Test results of eighteen beams subjected to sustained load for 180 days show that the deflection behavior depends on the longitudinal tension and compression reinforcement ratios and fiber content; excessive amount of compression reinforcement and fibers may have an unfavorable effect on the long-term deflections. The beams having the ACI Code's minimum longitudinal tension reinforcement showed much higher time-dependent deflection to immediate deflection ratio, when compared with that of the beams having about 50 percent of the balanced tension reinforcement. The results of theoretical analysis of tested beams and those of a parametric study show that the influence of steel fibers in increasing the moment of inertia of cracked transformed sections is most pronounced in beams having small amount of longitudinal tension reinforcement.

• 콘크리트학회논문집
• /
• 제20권6호
• /
• pp.765-772
• /
• 2008

철근콘크리트 구조물은 일반적으로 재료적 특성에 따른 크리프 및 건조수축으로 인하여 장기변형이 발생하며, 이러한 변형으로 인한 구조물의 처짐을 허용 한계 이하로 유지시키는 것이 사용성 확보 측면에서 중요하다 할 수 있다. 노후된 RC보의 성능 개선을 위하여 다양항 보수 보강 방법이 사용되고 있으며 이중 대표적인 방법으로 FRP 외부부착 공법이 있다. 재료적인 성질이 우수한 FRP는 RC구조물의 보강 재료로써 현재 널리 사용되고 있으며, 일시적인 하중 뿐만 아니라 지속 하중 하에서도 향상된 보강 성능을 제공해야 한다. 따라서 FRP가 외부 부착된 RC 부재에 지속 하중이 작용할 때 콘크리트의 크리프 및 건조수축의 영향으로 인한 시간 의존적 장기 거동을 정확히 예측하는 방법이 필요하다. 본 논문에서는 FRP가 외부 부착된 RC보의 장기 처짐 예측을 위해서, CFRP와 GFRP로 보강된 실험체를 제작하고, 25 kN의 지속하중을 470일간 가하여 시간 변화에 따른 처짐을 측정하였다. 또한, 이러한 처짐의 예측을 위하여 ACI-209 code 및 CEB-FIP code에 근거하여 크리프계수와 건조수축변형률을 산정하였으며, EMM과 AEMM을 사용한 ACI-318기준, Branson's method 그리고, Mayer's method를 사용하여 FRP가 외부 부착된 RC보의 장기 처짐을 예측하였다. 실험 결과, CFRP보 보강된 실험체가 가장 높은 장기 사용성을 보였으며, Mayer's method가 장기처짐에 대한 실험값을 가장 근사하게 예측한다는 것을 확인할 수 있었다.

• Wind and Structures
• /
• 제1권2호
• /
• pp.183-199
• /
• 1998

This paper discusses some of the findings arising from long-term monitoring of the wind effects on a transmission tower located on an exposed site in South-West England. Site wind speeds have been measured, together with the foundation loads at the base of each of the four legs. The results show good correlation between the wind speeds and leg strains (loads) for a given wind direction, as expected, for wind speeds in excess of 10 m/s. Comparisons between the measured strains and those determined from the UK Code of Practice for lattice towers (BS8100), for the same wind speed and direction, show that the Code over-estimates most of the measured foundation loads by a moderate amount of about 14% at the higher wind speeds. This tends to confirm the validity of the Code for assessing design foundation loads. A finite element analysis model has been used to examine the dynamic behaviour of the tower and conductor system. This shows that, in the absence of the conductor, the tower alone has similar natural frequencies of approximately 2.2 Hz in the both the first (transversal) and second (longitudinal) modes, whilst for the complete system and conductor oscillations dominate, giving similar frequencies of approximately 0.1 Hz for both the first and second modes.

• 제어로봇시스템학회논문지
• /
• 제17권1호
• /
• pp.61-67
• /
• 2011

The GPS new civil signal is modulated on the L2 carrier at a frequency of 1227.6MHz. The L2C signal is composed of two multiplexed code signals, which include CM code with a 10,230 chip sequency repeating every 20ms, and CL code which has a 767,250 chip sequency repeating every 1.5 seconds. Thus, the new civil signal have much improved cross correlation properties so that the position fixing can be possible even with very weak signals. However, it requires very long acquisition time because of its long code length. This paper presents an efficient signal acquisition method for L2C AGPS receiver. Snapshot mode and coarse time assistance are assumed and total integration time is given by 1.5 sec. By SNR worksheet and computer simulation, it is proven that L2C signal can be acquired with very weak power less than -150dBm. Considering the acquisition time and the sensitivity, it is recommended that the highest power signal is acquired with CM code first to reduce TTFF. By the timing synchronization, at this time, search space of the code phase for other signals can be greatly reduced so that CL code can be used in signal acquisition to maximize sensitivity with small computation.

• 한국안전학회지
• /
• 제29권5호
• /
• pp.97-103
• /
• 2014

To ensure durability and light weight of bridges, high-strength concrete is required for long-span deck slabs. Such a technology eventually extends the life of bridges and improves the economic efficiency. The results of this study suggests a formula for calculating the minimum thickness of long-span deck slabs built with high strength concrete. The minimum thickness is proposed based on the limit states indicated in the CEB-FIP Model Code and the Korean Highway Bridge Design Code(limit state design). The design compressive strength of concrete used for the study is 80MPa. Moreover, the required thickness for satisfying the flexural capacity and limiting deflection is estimated considering the limit state load combination. The formula for minimum thickness of deck slabs is proposed considering the ultimate limit state(ULS) and the serviceability limit state(SLS) of bridges, and by comparing the Korean Highway Bridge Design Code and similar previous studies. According to the research finding, the minimum thickness of long-span deck slab is more influenced by deflection limit than flexural capacity.

• 한국지진공학회논문집
• /
• 제17권4호
• /
• pp.151-157
• /
• 2013

In this study, an externally reinforced structural system for SMC(Sheet Molding Compound) panel water tank, designed according to the Japanese design code, is experimented to evaluate its seismic performance. The test tank is 3m long, 2m wide and 3m high, considering the capacity and size of the shaking table. The measured hydrodynamic pressures are found to be approximately 70% of the Japanese design code values. It may be partially due to the convex shape effect of the unit panels. The analytical results of externally reinforced system based on the measured dynamic water pressures are found in good agreement with the test results. If the design hydrodynamic pressures are estimated properly, the proposed analytical model for the externally reinforced water tank becomes a useful design tool and the Japanese design code is found to provide a safe design for the external frames of SMC panel water tank.

• 제어로봇시스템학회논문지
• /
• 제12권8호
• /
• pp.765-772
• /
• 2006

The L2 Civil Signal (L2CS) will be transmitted by modernized IIR(IIR-M), IIF and all subsequent GPS satellites. It contains two codes of different length; CM code contains 10,230chips, repeats every 20milliseconds and is modulated with message data, and CL code contains 767,250chips, repeats every 1.5second Z-count and has no data modulation. And the message data is encoded for Forward Error Correction(FEC). The long code length is useful for weak signal, but it also requires very long acquisition time. Therefore, the structure of GPS Ll/L2C Correlator and the fast acquisition scheme are proposed in this paper.