• Journal of the Korean Ceramic Society
• /
• v.38 no.12
• /
• pp.1155-1161
• /
• 2001

Yittrium Iron Garnet(YIG) has been used as an important material in the circulator/isolator which is used in RF communication system, mobile phone, adn satellite broadcasting, etc. In this study, we investigated the microstructural and magnetic properties of YIG ferrites with the sintering temperature and additives. We fabricated the YIG ferrites substituted with Ca, In, V by the traditional ceramic sintering method at 1250$\^{C}$, 1275$\^{C}$, 1300$\^{C}$ and 1325$\^{C}$. Powders were granulated by using a spray dryer. Crystallographic and microstructural properties were measured by using XRD and SEM. Magnetic properties were measured by using a VSM for saturation magnetization (4$\pi$M$\_$s/) and FMR (Ferromagnetic Resonance) experiment for ferromagnetic resonance line width (△H). The YIG ferrite, Y$\_$1.6/Ca$\_$1.4/Fe$_4$V$\_$0.7/In$\_$0.3/O$\_$12/, sintered at 1300$\^{C}$, showed higher saturation magnetization and lower ferromagnetic resonance line width than any other sintering temperatures.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.8
• /
• pp.1137-1142
• /
• 2013

FBG sensors are mainly used to measure strain and temperature of structures. In this paper, an interrogator of FBG sensors is developed and implemented to measure the crack of structures using FPGA and DSP. Developed interrogator consists of an optical source, an optical circulator, an optical grating and a CCD sensor and controller. The spectrum of the reflected light from the FBG sensor is analyzed and peak wavelength is detected. Next, strain of structure can be measured using shift of peak wavelength. Centroid algorithm and Gaussian fitting which are mainly applied to detect peak wavelength of the interrogator are compared in this paper. As a result of experiment, Gaussian fitting is suitable for a developed interrogator.

• Korean Journal of Optics and Photonics
• /
• v.13 no.3
• /
• pp.235-239
• /
• 2002

A novel ultra-narrow linewidth DFB laser in the extended FBG ring cavity having kHz linewidth is presented. The method of linewidth compression was realized by introducing an extended fiber ring cavity into the cavity between the external FBG and the Bragg grating inside a DFB laser diode. Optimum optical feedback control was achieved by using an optical circulator and a variable optical attenuator to prevent mode hopping induced by spatial hole burning. To prove the validity of the proposed scheme, a self-heterodyne measurement set-up with fiber delay line of 63 km was utilized for the ultra-narrow linewidth measurement. A 3 dB linewidth of less than 3 kHz was demonstrated, which is resolution limited performance. This linewidth is equivalent to 3 dB linewidth of 2$\times$10$^{-8}$ nm.

• Journal of electromagnetic engineering and science
• /
• v.9 no.4
• /
• pp.188-193
• /
• 2009

A K-band low-power miniaturized planar-type hyperthermia system was developed to replace massive and expensive equipment. The system consists of a VCO with a buffer amplifier, a high-power amplifier module, a 20-dB-coupled line coupler, a chip circulator and two power detectors for signal generation, amplification and power monitoring. All these components have been implemented in planar form on two module blocks. The total size of the hyperthermia system was less than $10\times6.5\times3\;cm^3$. In order to verify the system performance, ablations were carried out on nude mice xenografted with human breast cancer. Ablation results show performance comparable to the massive components-based system. This work shows the feasibility of a low-cost miniaturized hyperthermia system for practical clinical applications.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.6 no.3
• /
• pp.175-181
• /
• 1994

This paper deals with the correlation of absorption rate in absorber and evaporation rate in evaporator. The evaporator consists of a copper tube of 10mm dia, and 600mm long and chilled water flowing through the tube is fed by the chilled water circulator. The flowrate of LiBr-water solution in the absorber plays a significant role in determining the magnitude of the heat transfer rate from chilled water to refrigerant There exists a flowrate of solution which has a maximum value of heat transfer. It is interesting to note that the absorption rate of absorber increases with increasing the heat transfer rate of the evaporator. Also, absorption rate increases with evaportation rate, and the ratio(the former/the other) depends on the inlet temperature of LiBr-water solution in the absorber. The heating capacity in the absorber is higher than the refrigerating capacity in the evaporator.

• Nuclear Engineering and Technology
• /
• v.41 no.3
• /
• pp.307-318
• /
• 2009

KAERI (Korea Atomic Energy Research Institute) has developed the GAMMA+ code for a thermo-fluid and safety analysis of a VHTR (Very High Temperature Gas-Cooled Reactor). A key safety issue of the VHTR design is to demonstrate its inherent safety features for an automatic reactor power trip and power stabilization during an anticipated transient without scram (ATWS) accident such as a loss of forced cooling by a trip of the helium circulator (LOFC) or a reactivity insertion by a control rod withdrawal (CRW). This paper intends to show the ATWS assessment capability of the GAMMA+ code which can simulate the reactor power response by solving the point-kinetic equations with six-group delayed neutrons, by considering the reactivity changes due to the effects of a core temperature variation, xenon transients, and reactivity insertions. The present benchmark calculations are performed by using the safety demonstration experiments of the 10 MW high temperature gas cooled-test module (HTR-10) in China. The calculation results of the power response transients and the solid core temperature behavior are compared with the experimental data of a LOFC ATWS test and two CRW ATWS tests by using a 1mk-control rod and a 5mk-control rod, respectively. The GAMMA+ code predicts the power response transients very well for the LOFC and CRW ATWS tests in HTR-10.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.7 no.2
• /
• pp.43-49
• /
• 2008

In this paper, new directional couplers for T/R switch of UHF RFID applications are proposed to overcome TX-to-RX leakage problem. The proposed method can remove TX-to-RX leakage caused by both imperfect isolation characteristic of the conventional directional coupler and the mismatch of antenna impedance. Two directional couplers are implemented using distributed elements and lumped elements respectively for the verification. The varactor tuneable circuits for compensation of the antenna mismatch is also proposed. The measurement result shows excellent TX-to-RX leakage suppression, more than 45dB in 910MHz.

• Applied Chemistry for Engineering
• /
• v.8 no.2
• /
• pp.246-251
• /
• 1997

The phase behavior of sucrose monopalmitate/alkanol/water ternary system was investigated. According to compositions of three components ranging from micellar(or inverse micellar) solution up to various lyotropic liquid crystalline(LC) phase, each texture of the separated phases was identified by crossed polarizers equipped with a camera whose stage was connected to a thermostatic circulator. As the carbon atom number in alkanol of the polar oily substance increases, patterns of the various LC phases were also observed hexanol

• Journal of the Optical Society of Korea
• /
• v.13 no.3
• /
• pp.330-334
• /
• 2009

A simple and compact frequency swept laser is demonstrated at $1.3{\mu}m$ using a wavelength scanning filter based on a rotating slit disk. The laser is comprised of a pigtailed semiconductor optical amplifier, a circulator, and a wavelength scanning filter in an extended cavity configuration. The wavelength scanning filter is composed of a collimator, a diffraction grating, a rotating slit disk, and a mirror. The instantaneous laser output power is more than 5 mW. The scanning range of the laser is extended to 80 nm at the maximum level, and 55 nm in the full width at half maximum at a scanning rate of 2 kHz.

• Aerospace Engineering and Technology
• /
• v.1 no.1
• /
• pp.135-140
• /
• 2002

The position and trajectory of in-flight rocket are important informations to determine the flight safety of rocket. In general tracking system, radar and transponder are used to acquire position information. Rocket position and trajectory can be determined by using RF communication between ground station and in-flight rocket and antenna position data. Onboard transponder system is composed of RF receiving part, RF transmitting one, decoder and single TX/ RX antenna. Therefore circulator is necessary for minimizing RF signal interference. In this paper, the radar transponder system was developed to track the trajectory and position of KSR-Ⅲ by using radar.