• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.4
• /
• pp.320-323
• /
• 2019

This paper examines a disadvantage of low-frequency magnetic shielding measurement based on MIL-STD-188-125-1. A rectangular loop antenna is proposed as an improvement over conventional circular loop antennas for measuring magnetic shielding. Simulation and experiment are used to demonstrate that the proposed rectangular loop outperforms the circular loop for a more reliable shielding measurement at low frequency range.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.11
• /
• pp.1051-1061
• /
• 2004

In this Paper, a new antenna(VHMDA) characteristics of half-circular/elliptical disc-loaded planar antennas with horizontally top-loaded small disc is studied by simulation and measurements with additional resonant structure. The transfer function characteristics of Gaussian pulse from the designed UWB transmitter antenna has been investigated. The radiation pattern of the proposed antenna in azimuth is nearly omni-directional response, which is usulally required in conventional monopole antenna. In addition to that, the simulation and measured results show that the return loss characteristics of VHDMA covers considerably large bandwidth with small area. From the measured results of the circular and half-circular disc-loaded monopole antennas with small disc mounted on the top, it is found that the half disc-loaded monopole antenna with additional structure can be comparable to the circular disc-loaded monopole antenna in respect o( size and electrical performances. Surface wave and dielectric losses often caused by the printed antenna using high dielectric constant does not occur in metallic planar antenna with good impedance matching and without lossy matching unit. This structure implies that the performance of return loss is directly related with the radiation efficiency.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.4
• /
• pp.894-900
• /
• 2004

There are many types of circularly polarized(CP) microstrip antenna elements, which are used as a good unit radiator. Since an advantage of CP antenna is no strict alignment requirements between Rx and Tx system, the printed antennas with circular polarization are very often used in numerous satellite and mobile radio systems. In order to realize the broad bandwidth of 3 dB axial ratio and impedance of CP microstrip antenna, complex feed structure and tri-plate patch element have been researched. This paper describes a design of wideband microstrip cross slot array antennas with circular polarization. The proposed antenna is composed of an open-ended microstrip feed line as a feeder and a cross slot as a radiator for circular polarization. To realize the wide bandwidth, tri-plate structure are considered and cross slot is electromagnetically coupled with feed line. Optimum parameters of 1-element cross slot antenna are analyzed and designed by method of moments. These parameters are also applied to may antennas design considered the mutual coupling between radiating elements. Right hand circular polarization(RHCP) and left hand circular polarization(LHCP) of the proposed antenna are easily controlled by asymmetrical cross slot structure and slot position. In 1-element and 15-element cross slot array antenna, the good axial ratio of 1 dB below and the broad bandwidth characteristics of antenna are obtained.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.04a
• /
• pp.107-110
• /
• 2003

본 연구에서는 3차원 브레이딩 기계를 이용하여 제작된 6 layer의 3차원 원형 형태로 브레이드된 유리 섬유 강화 복합재료의 프리프레그를 이용하여 에폭시 수지를 모체로 하는 RTM(Resin Transfer Molding) 공정을 통해 직교 이방성 복합재료를 제작하였다. 또한 탄성한계 내에서의 구성방정식을 얻기 위해 unit cell 모델링을 통해 복합재료의 기하를 모사하고 method of cells 이론과 homogenization technique를 이용하여 복합재료의 구성방정식을 나타내는 수치해석 코드를 개발하였다. (중략)

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.579-582
• /
• 1999

This paper represents the results of experiments designed to investigate the time-dependent response of concrete and steel tube in circular concrete-filled steel tubes, as are deployed extensively in high-rise building construction. The experiments were performed for creep of concrete and CFT column specimens with three loading cases. The creep coefficient and specific creep(unit creep) obtained from the test results were used for estimating and comparing the time-dependent response of each case. From these analyses, it is show that CFT-column has many merits for long-term behavior.

• Journal of Energy Engineering
• /
• v.8 no.1
• /
• pp.7-13
• /
• 1999

원형 용융탄산염 단위 연료전지의 성능 및 온도분포가 수치모사를 통해 얻어졌다. 원형 단위전지내에서는 사각형 단위전지에 비해 비교적 균일한 온도분포가 얻어졌다. 전지의 바깥쪽으로 갈수록 가스전환율이 커졌고 전류밀도도 크게 증가하였다. 운전전압이 감소할수록 각 가스들의 전환율은 커지고 전류밀도도 커졌다. 원형 전지에서의 평균전류밀도나 출력은 전압이 높을 때는 사각형 전지보다 작았고, 전압이 낮을 때는 더 컸다. 음극 및 양극 가스의 전환율도 마찬가지였다. 전압이 낮을 때 가스의 전환율이 커서 원형 전지의 효용성이 크게 나타났다.

• 전기의세계
• /
• v.21 no.4
• /
• pp.22-26
• /
• 1972

The vibration of power lines in rainy environments was researched using the concentric cylindrical gap to which D.C. voltage was applied. Consequently, it has been solidly conformed that the vibration of power lines begins at threshold voltage of corona, and that the amplitude of the vibration increases as the numbers of falling water drop per unit time increase. The vibration phenomen take place in straight line, elliptic or circular motion as voltage is applied the numbers of vibration nearay accord with the elastic vibrarion theory.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.633-638
• /
• 2000

This paper reports an example of flow-induced vibration in a very large plant and the whole procedure of reducing the vibration. During the operation of flue gas desurfurization unit of the thermal power plant, serious vibration occurred at all around the unit. The worst vibration was recorded on the heat exchanger surface, which weighed 180 tones, as 17.8 m/$s^2$ in vibration amplitude at 34Hz. To identify the vibration, frequency analysis on the response vibration, the expected excitation force and the system resonance was executed. This investigation revealed that the cause of the vibration was vortex shedding from the circular pipes in the heat exchanger. Vortices from the pipes excited acoustic resonance in the heat exchanger room, which, in turn, made the structure vibrate. Through inserting the baffles between the pipes, which had an effect of cutting the acoustic wave at resonance frequency, the vibration was eliminated dramatically.

• Journal of KSNVE
• /
• v.9 no.6
• /
• pp.1200-1209
• /
• 1999

This paper reports a peculiar example of flow-induced vibration in a very large plant and the whole procedure of reducing the vibration. During the operation of flue gas desurfurization unit of the thermal power plant, serious vibration was dtected at all around the plant. The worst vibration was recorded on the heat exchanger surface, which weighed 180 tones, as 17.8 m/$s^2$ in vibration amplitude at 34 Hz. To identify the vibration, frequency analysis on the response vibration as well as on the expected excitation forces and the system resonance was executed. This investigation revealed that the cause of the vibration was vortex shedding from the circular pipes in the heat exchanger. Vortices from the pipes excited acoustic resonance in the heat exchanger room, which, in turn, made the structure vibrate. Through inserting the baffles between the pipes, which had an effect of cutting the acoustic wave at resonance frequency, the vibration was eliminated dramatically.

• Bulletin of the Korean Chemical Society
• /
• v.16 no.1
• /
• pp.42-47
• /
• 1995

Interpolymer complex formation between basic polypeptide poly(L-proline) Form Ⅱ (PLP(Ⅱ)) and acidic polypeptides poly(L-glutamic acid) (PLGA) and poly(L-aspartic acid)(PLAA) has been studied in water-methanol (1:2 v/v) mixed-solvent by viscometry, potentiometry, light scattering and circular dichroism (CD) measurements. It has been found that polymer complexes between PLP(Ⅱ) and PLGA (or PLAA) are formed via hydrogen bonding with a stoichiometric ratio of PLP(Ⅱ)/PLGA (or PLAA)=1:2 (in unit mole ratio) and that PLP(Ⅱ) forms polymer complex more favorably with PLGA than with PLAA. In addition, the minimum (for pH 5.0) and the maximum (for pH 3.2) in reduced viscosity of dilute PLP(Ⅱ)-PLGA mixed solutions are observed at 0.67 unit mole fraction of PLGA (i.e., [PLP(Ⅱ)]/[PLGA]=1/2). These findings could be explained in terms of molecular structure (or conformation) of the complementary polymers associated with the complex formation.