• Journal of the Mineralogical Society of Korea
• /
• v.22 no.1
• /
• pp.13-22
• /
• 2009

The study area is a tunnelling section passing through the Yangsan Fault zone. Kyungbu express highway and national road 35 are located above the tunnel. Previous study showed that fault gouge and fault breccia were widely distributed in the tunnelling section with a maximum width of 100 m. From the present study, it is found that sedimentary rocks consisting mainly of shale are distributed at the eastern block of the Yangsan Fault and these rocks are not subject to mechanical fracturing and hydrothermal alteration. On the other hand, dacitic tuff distributed at the western block of the Yangsan Fault is largely affected by mechanical fracturing and hydrothermal alteration. The large fault zone of $50{\sim}130m$ width was formed by complex processes of mechanical fracturing and hydrothermal alterations such as chloritization, sericitization, and kaolinization. Based on the characteristics of mechanical fracturing and hydrothermal alterations, the Yangsan fault zone in the study area is geotechnically classified as four zones: unaltered zone, altered zone, altered fractured zone, and fault gouge zone. These zones show different degrees and aspects in mechanical fracturing and hydrothermal alterations, resulting in different engineering properties.

• Economic and Environmental Geology
• /
• v.24 no.3
• /
• pp.233-244
• /
• 1991

A biotite that substantially altered to chlorite and vermiculite in hornblende gneiss from Cheonyang, Korea, has been investigated with electron microprobe analysis. The data show the general variational trends of Ti and K-leaching with increased weathering. However, the chloritization is characterized by Si- conservative reaction and relatively dramatic increase of Al-for-(Fe+Mg) octahedral substitution, whereas the vermiculitization is characterized by total Mg-conservative and Ca-enriching exchange reaction. In the initiating stage the vermiculitization proceeded in a continuous decrease of the Al-for-Si tetrahedral substitution and an increase of the Al-for-(Fe+Mg) octahedral substitution, supporting the currently accepted weathering process. But it differs in the late stage, in which AI(IV) and Fe increase significantly. Recalculations of the structural formular for vermiculite on the basis of several assumptions indicate that the oxidation of Fe is necessary for vermiculite to form the reasonable strutural formular. The relative timing of the oxidation of Fe probably occurs in the late stage, supported by the substantial increase of the Al-for-Si tetrahedral substitution.

• Economic and Environmental Geology
• /
• v.25 no.3
• /
• pp.297-316
• /
• 1992

The Daebong gold-silver deposits is located in 8 km southwest of Cheongyang, Chungcheongnam-Do, Republic of Korea. The gold-silver-bearing hydrothermal quartz veins was formed within the Precambrian metasediments of Gyeonggi massif. Ore minerals occur as mainly of pyrite, sphalerite (0.78~6.19 wt.% Cd), galena, pyrrhotite and minor amounts of chalcopyrite, arsenopyrite, magnetite, ilmenite, chalcocite, electrum (55.00~89.55 wt.% Au) and argentite. The gangue minerals are quartz, calcite, chlorite, K-feldspar, biotite. Wall-rock alterations such as chloritization, silicification, pyritization, carbonatization and sericitization can be observed near the quartz veins. According to the mineral paragenetic sequence based on vein structure and mineral assemblages, three stage mineralizations can be recognized. Fluid inclusion, sulfur isotope and thermodynamic data show that the ore minerals were dominantly deposited at the between 388 and $204^{\circ}C$ from fluids with salinities of 8.1~0.3 wt.% equivalent NaCl, and sulfur isotope value 4.84 to 6.40 per mil of sulfides indicates igneous sources of sulfur in the hydrothermal system and fluid inclusion salinity data suggest that thermal fluids may have magmatic origin with some degree mixing of meteoric water.

• Ocean and Polar Research
• /
• v.23 no.1
• /
• pp.11-21
• /
• 2001

K-Ar ages of the altered rocks from the Barton Peninsula are belows; altered tuffaceous andesite from southwestern part is 42 Ma, altered rocks contacted with quartz vein from southern part are 28 and 33 Ma, and advanced argillic altered andesite from northeastern part are 33 and 35 Ma. Those K-Ar ages are 10 My younger than granitic rocks of the Barton Peninsula. Hydothermal alteration of the Barton Peninsula was originated from mixing of magmatic water from parent magma of granitic rocks with meteoric water. The Al content in the hostrock is relatively constant during hydrothermal alteration, on the contrary the Mg content is in proportion to total alkali. The variation of total alkali and Mg contents in hydrothermal alteration indicates that those elements was washed out during hydrothermal alteration. The sequences of hydrothermal alteration of the Barton Peninsula is chloritization of amphiboles, sericitization of feldspars and kaolitization of sericite.

• Geomechanics and Engineering
• /
• v.20 no.3
• /
• pp.233-241
• /
• 2020

Alkali-silica reaction (ASR) is among one of the most important damaging mechanisms in concrete, depending primarily on aggregates which contain reactive minerals. However, expansion in concrete may not directly relate to the reactive minerals. This study aims to investigate the influence of ASR and the expansion of mortar bars depending on aggregate type containing various components such as quartz, clay minerals (montmorillonite and kaolinite) and micas (muscovite and biotite). In this study, the accelerated mortar bar tests (AMBT) were performed in two conditions (mortar bars in the same and sole NaOH solutions). Petrographic thin section studies, X-ray diffraction (XRD) analysis (Rietveld method), scanning electron microscopy (SEM) and chemical analyses were carried out. This study showed that quartzite bars led to increase in expansion values of mortar bars in diabase-1 and andesite when these were in the same NaOH solution. However, three samples (basalt, quartzite and claystone) were found having ASR expansion based on the AMBT when the special molds were used for each sample. SEM study revealed that samples which exhibit highest expansions according to AMBT had a generally rough surface and acicular microstructures in or around the micro-cracks. Basalt and quartzite showed more variable in major oxides than those of other samples based on the chemical analyses, SEM studies and AMBT. This study revealed that the highest expansions were observed to source not only from reactive aggregates but also from alteration products (silicification, chloritization, sericitization and argillisation), phyllosilicates (muscovite, biotite and vermiculite) and clays (montmorillonite and kaolinite).

• Economic and Environmental Geology
• /
• v.27 no.6
• /
• pp.537-548
• /
• 1994

The Weolyu gold-silver deposits at Hwanggan, Chungcheongbukdo, is of a late Cretaceous $(74.24{\pm}1.63Ma)$ epithermal vein-type, and is hosted in the quartz porphyry of late Cretaceous age. Based on mineral paragenetic sequence interpreted from vein structure and mineral assemblages, three stages mineralization were distinguished. A variety of ore minerals occurs including pyrite, sphalerite, chalcopyrite, galena with small amount of electrum, native silver, argentite, pearceite, sb-pearceite, argyrotite. The gangue minerals are quartz, rutile, calcite, apatite, fluorite and rhodochrocite. Wall-rock alteration such as pyritization, chloritization, sericitization, silicification is observed near the quartz veins. Au-Ag minerals were crystallized at middle and late stage of the two mineralization sequences. Results from the analysis of fluid inclusion and thermodynamic calculation indicate that Au-Ag mineral deposits were formed primarily by cooling and dilution of hydrothermal fluids($165{\sim}313^{\circ}C$, 0.4~2.4wt.% equivalent NaCl) with some degree mixing of meteoric water.

• Economic and Environmental Geology
• /
• v.23 no.2
• /
• pp.161-181
• /
• 1990

The lead-zinc-silver-iron deposits from the Janggun mine are of hydrothermal-metasomatic origin, characterized by the marked hydrothermal alteration of the wallrocks, such as hydrothermal manganese enrichment of carbonate rocks, silicification, chloritization, sericitization, montmorillonitization and argillic alteration. The ore deposits have been emplaced within the Janggun Limestone of Cambro-Ordovician age at the immediate contacts with apophyses injected from the Chunyang Granite plutons of Late Jurrasic age. They have been structurally controlled by fractures in the carbonate rocks and the irregular intrusive contacts of granitic rocks, and are closely associated with hypogene manganese carbonate deposits. In the mine nine seperate orebodies are being mined. On the basis of the petrological study, hydrothermal alteration zone of this mine may be divided into the following four zones from wallrock to orebody. (I) Primary calcite and dolomite zone${\rightarrow}$(II) dolomitic limestone zone${\rightarrow}$(III) dolomitic zone${\rightarrow}$(IV) rhodochrosite zone${\rightarrow}$ orebody. There was not recongnized Mn and Fe elements in the primary calcite and dolomite zone. But, in the dolomitic limestone and dolomite zone, calcite and dolomite were subjected to weak hydrothermal manganese enrichment and the grade of the manganese enrichment increase oreward. By means of electron probe microanalysis, it was found that manganoan dolomite occured between primary dolomite grains, cross the cleavage of the primary dolomite and around the dolomite grains. Above these result supports that the Janggun manganese carbonate deposits are of hydrothermal metasomatic origin.

• Economic and Environmental Geology
• /
• v.6 no.3
• /
• pp.133-170
• /
• 1973

The metamorphosed belt on cherty and andesitic rocks of the Gyeongnam province area has been well known as the most important copper matallogenetic province in Korea and locally has been investigated by several geologists. This report is summarized about geology, occurrence of ore deposits, the study of the present status of mine developments and exploitations and the suggestions of future proposed of copper mine developments and harmoniously and reseonably planning of demands and supply of copper ore. For convenience of study the writer divided the survey region as 4 areas, according to the conditions of mine location. They are (1) Goseong copper area (2) Gunbuk-Haman copper area (3) Masan-Changwon copper area (4) Tongrae-Ilgwang copper area. The geology of the above 4 areas consits of Cretaceous Gyongsang System, which is divided into Silla series, Nakdong Series and Bulguksa Series. The former has intrusive and extrusive andesite and sedimentary formation, and the latter has dioritic and hornblende granite. Ore deposits which is mostly vein types are confined mostly in the andesite and cherty rocks of Silla and Nakdong Series. It is observed slight hydrothermal alteration, i. e. propylitization, chloritization, saussuritization and silicification. It seems that the ore was formed by hydrothermal solution and secondary enrichement. The ore minerals are mainly chalcopyrite and pyrite, with small amounts of malachite, azurite, chalcocite, cuprite, galena, and sphalerite, magnetite, tetrahedrite and etc.. The efficient plan of copper mine developments in surveyed region are as following; (a) Gyeongnam Copper districts are divided in 4 area as mentioned above. (b) Each area would be likely developed as group-working as one unit. For the sufficiently supplying a demand of electric copper, the importations of high grade copper ore in foreign country are invitable at present status of copper mine developments and exploitations.

• Economic and Environmental Geology
• /
• v.2 no.3
• /
• pp.58-67
• /
• 1969

Songgwang lead zinc mine is located in about 12km to the north-east of Jeonju City. Geology of the mine and its visinity is consisted of Jeonju series belonged to so-called Okcheon system, Seodaesan tuff formation, Silla series, and the quartz porphyry intruded into these formations. Jeonju series comprising 3 formations; that is, of Sadaeri, Sindong, and Girinbong. Jeonju series is generally distributed in southern part of the area, striking NNW, and diping NE $30^{\circ}$, or NW $30^{\circ}$. It is deformed to form synclinorium and anticlinorium plunging to the north with low angle. In the northern part of the area, Jeonju series was cut by Sinpeongri-fault of NEE direction near Sinpeongri. In the north side of the fault, it is overturned and shows NEE or NWW strikes and NW $60^{\circ}$ dips. At the west of Songgwangri, it is cut by 3 thrusts; the two are almost parallel each other, and the third oneis manifested by the fact that the lower black shale zone thrusted over the upper limestone. Songgwangri thrust, so named, is a post-mineral fault and its plane represents a premineral slip plane. Enrichment of are took place along the bedding plane or fissure parallel to it, as seen in adit No. 1 or No. 2 along the floor of the thrust, and along the sheared zone or the brecciated zone oblique to the plane near the thrust in crystalline limestone of Sindong formation as observed in the underground levels of inclined slope. Ore minerals are chiefly zincblende, galena, pyrrhotite, arsenopyrite, acompanied pyrite and chalcopyrite, and contain Au and Ag. In earlier stage of mineralization, the limestone was recrystalized, and sulphide minerals were enriched in the· permiable zone said above by pyrometasomatism, and in later stage the limestone was affected chloritization and sericitization. However hydrothermal replacement was weak, so that enrichment did not took place. It seems that minerallizing materials came up through the premineral slip plane and injected, and replaced the limestone in permiable zone said above with sulphide are minerals. Then Songgwangri thrust took place and, the lower black shale zone thrusted upon crystalline limestone.

• Economic and Environmental Geology
• /
• v.22 no.3
• /
• pp.237-252
• /
• 1989

The Inseong gold-silver mine is located 3Km northwest of Suanbo, Choongcheongbugdo, Republic of Korea. The mine occurs in the shear zone formed by tension fractures within the Hwanggangri Formation of the Ogcheon metamorphic belt. Ore minerals found in the gold-silver bearing hydrothermal quartz vein composed mainly of pyrite, arsenopyrite, sphalerite, galena and minor amount of chalcopyrite, pyrrhotite, stannite, bismuthininte, native bismuth, chalcocite, electrum and tellurian canfieldite(?). The gangue minerals are quartz, calcite, chlorite and rhodochrocite. Wallrock alterations such as chloritization, silicitication, pyritization, carbonitization and sericitization can be observed in or around the quartz vein. According to the paragenetic sequence, quartz vein structure and mineral assemnlages, three different stages of ore formation can be recognized. The physico-chemical environment of ore formation in this deposit shows slight variation from stage to stage, but the condition of main ore deposition can be summarized as follows. Fluid inclusion, S-istope geothermometry and geothermometry based on mineral chemistry by use of arsenopyrite and chlorite show the ore was formed at temperature between 399 and $210^{\circ}C$ from fluids with salinities of 3.3-5.8 wt.% equivalent NaCl. It indicates that pressure during the mineralization is less than 0.6 Kb corresponding to a depth not greater than 1Km. S-isotope data suggests that thermal fluid may have magmatic origin wit some degree of mixing with meteoric water. In coclusion, the Inseong gold-silver deposit was formed at shallow depth and relatively high-temperature possibly with steep geothermal gradient under xenothermal condition.