• Journal of the Korean Institute of Gas
• /
• v.22 no.3
• /
• pp.38-44
• /
• 2018

Ammonia is used primarily as a refrigerant in refrigeration facility and SCR of a plant, and is frequently involved in leakage accidents. This study was conducted by selecting ammonia, a material with a wide influence range when evaluated, as a material with higher vapor pressure and lighter than air. In this study, the influence ranges were computed using KORA(Korea Off-site Risk Assessment supporting tool) with four different environmental factors : ground roughness, sealing, operating temperature, pressure, and leakage hole size. As a result, the difference in the influence range of ground roughness is approximately 4.62 times, while the ammonia storage tank shows a difference in the reduction rate of 0.64 when sealed. The extent of impact increased with increasing leakage depending on storage temperature and pressure, and when storing higher than the saturation vapor pressure, the impact range showed an average growth rate of 3.45 % per 0.1 Mpa($45^{\circ}C$). The influence ranges based on the size of the leakage holes is shown to be proportional to the area of the leakage zone.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.4
• /
• pp.132-137
• /
• 2018

Although the number of chemical accidents has been declining since the Chemical Control Act of 2015, there have been repeated occurrences of similar types of accidents at printed circuit board (PCB) manufacturing facilities. These accidents were caused by the overflow of hydrochloric acid and hydrogen peroxide, which are toxic chemicals used in the printed circuit board manufacturing process. An analysis of the $Cl^-$ content to identify the cause of the accident showed that in the mixed route of hydrochloric acid and hydrogen peroxide, which are accidental substances, the $Cl^-$ concentration was 66.85 ppm in the hydrogen peroxide sample. Through reaction experiments, it was confirmed that the deformation of a PVC storage tank and generation of chlorine gas, which is a toxic gas, occurred due to reaction heat occurring up to $50.5^{\circ}C$. This paper proposes a facility safety management plan, including overcharge, overflow prevention, leak detection device, and separation tank design for mixing prevention in printed circuit board manufacturing facility etch process. To prevent the recurrence of accidents of the same type, the necessity of a periodic facility safety inspection and strengthening of the safety education of workers was discussed.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2003.04a
• /
• pp.418-421
• /
• 2003

Surfactant enhanced in-situ soil flushing was peformed to remediate the soil and groundwater at an oil contaminated site, and the effluent solution was treated by the chemical treatment process including DAF(Dissolved Air Flotation). A section from the contaminated site(4.5m$\times$4.5m$\times$6.0m) was selected for the research, which was composed of heterogeneous sandy and silt-sandy soils with average Hydraulic conductivity of 2.0$\times$10$^{-4}$ cm/sec. Two percent of sorbitan monooleate(POE 20) and 0.07% of iso-prophyl alcohol were mixed for the surfactant solution and 3 pore volumes of surfactant solution were injected to remove oil from the contaminant section. Four injection wells and two extraction wells were built in the section to flush surfactant solution. Water samples taken from extraction wells and the storage tank were analyzed by GC(gas-chromatography) for TPH concentration with different time. Five pore volumes of solution were extracted while TPH concentration in soil and groundwater at the section were below the Waste Water Discharge Limit(WWDL). Total 18.5kg of oil (TPH) was removed from the section. The concentration of heavy metals in the effluent solution also increased with the increase of TPH concentration, suggesting that the surfactant enhanced in-situ flushing be available to remove not only oil but heavy metals from contaminated sites. Results suggest that in-situ soil flushing and chemical treatment process including DAF could be a successful process to remediate contaminated sites distributed in Korea.

• Journal of Korea Port Economic Association
• /
• v.25 no.1
• /
• pp.63-86
• /
• 2009

With increasing uncertainty of energy market in the world, the policies for the energy resource security have become crucial Several countries with poor energy resource like Netherlands and Singapore have pursued the policy for becoming an oil hub in the region. Singapore has been an oil hub in East Asia for a long time not only because it is well located with a large number of countries exporting and importing oil but it has also pursued strong policies to become an oil hub while establishing favourable institutional, regulatory and business environment for accommodating major refineries and petro-chemical companies. However with growing trading volume of petroleum products in Northeast Asia and a record high price of oil in these days, the necessities of another oil hub in the region are considered in order to reap benefits of the security of economical and stable oil. South Korea is situated astride the main North Pacific shipping route, with deep water ports and proximity to Chinese and Japanese industrial centres that make tank terminal operators Ideal choices for the oil hub in Northeast Asia although it has several disadvantages such as lack of independent storage facilities, underdeveloped oil trading market and unfavourable business friendly climates etc. This study is focused on examining the globalization strategies of tank terminal operators such as Vopak, Oiltanking and Odfjell in order to suggest the policy implications for becoming an oil tub in Northeast Asia.

• Journal of the Korean Institute of Gas
• /
• v.5 no.4 s.16
• /
• pp.40-48
• /
• 2001

For a Liquified Petroleum Gas(LPG) station, the reliability analysis, such as Fussell-Vesely importance, risk decrease factor and risk increase factor, was carried out and the risk ranks of events were determined. In order to confirm the degree of the risks identified in the reliability analysis, the quantitative risk analysis was done for the equipments which had the large values of risk ranks. As a result of the importance analysis for the LPG station, the external event was identified as the most riskful event. The defect of construction structure and the pipe corrosion were riskful as well. The result of quantitative risk analysis showed that the length of 46.3 meters were estimated to damage the process equipments by the thermal flux from the catastrophic rupture of storage tank in Boiling Liquid Expanding Vapor Explosion.

• Journal of the Korean Institute of Gas
• /
• v.13 no.1
• /
• pp.61-67
• /
• 2009

There are lots of energy facilities using gas(storage facility, compressed gas pipe, station, tank lorry) on the domestic. These major gas facilities cause major accidents associated with fire, explosion, toxic and etc. With the increased interest in reducing air pollution, supply of natural gas for gas vehicles is increasing. Thus, the number of establishments of LNG (Liquefied Natural Gas) and CNG(Compressed Natural Gas) stations is increasing as well. However, due to major gas accidents such as the fire and explosion accident of a Buchen LPG (Liquefied Petroleum Gas) station, it is difficult to establish a new station. In this research, we present quantitative risk assessment for LCNG;LNG multi-station and compare it result against individual risk criteria of HSE.

• Clean Technology
• /
• v.20 no.1
• /
• pp.1-6
• /
• 2014

$CO_2$ is generated by the combustion reaction, when getting the energy from fossil fuel. If the carbon dioxide emissions increases more, the global warming problem will become more serious. CCS (carbon capture storage) needs to be developed for the prevention of this. When liquefied $CO_2$ is transported, BOG (boil-off gas) is generated because of several problems. In the study, by injecting liquefied $CO_2$ in two tanks which contains $40m^3$each, the amount of BOG and its composition were measured during 30 days when generating pressure changes and external heat, loading, unloading. In result, 16,040 kg of BOG was generated and the composition has been found out to be 99.95% $CO_2$ and 0.05 % $N_2$. Also, we conducted simulation process for reliquefaction of generated BOG with vapor compression cycle using the PRO/II with PROVISION version 9.2. As a result, the refrigeration cycle of the total circulation flow rate was 42.07 kg/h and the condenser utility consumption was 48.85 kg/h.

• Korean Chemical Engineering Research
• /
• v.57 no.1
• /
• pp.42-50
• /
• 2019

As the industry develops in Korea, the use of hazardous chemicals is increasing rapidly and chemical accidents are increasing accordingly. Most of the chemical accidents are caused by leaks of hazardous chemicals, but there are also accidents in which all the substances are released instantaneously due to sudden high temperature/pressure or defection of the storage tanks. This is called catastrophic failure and its frequency is very low, but consequence is very huge when it occurs. In Korea, there were 15 casualties including three deaths due to catastrophic rupture of water tank in 2013, and 64 instances of failures from 1919 to 2004 worldwide. In case of catastrophic failure, it would be able to overflow outside the bund that reduces the evaporation rate and following consequence. This incident is called overtopping. Overseas, some researchers have been studying the amount of external overflow depending on bund conditions in the event of such an accident. Based on the previous research, this study identified overtopping fraction by condition of bund in accordance with Korea Chemicals Controls Act Using CFD simulation. As a result, as the height increases and the distance to the facility decreases while meeting the minimum standard of the bund capacity, the overtopping effect has decreased. In addition, by identifying the effects of overtopping according to atmospheric conditions, types of materials and shapes of bunds, this study proposes the design of the bund considering the effect of overtopping caused by catastrophic failure with different bund conditions.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.2
• /
• pp.102-110
• /
• 2017

In this paper, the liquid oxygen filling system (LOXFS) of the launch complex system of Korea Space Launch Vehicle-II (KSLV-II) is introduced based on critical design result by KARI in 2015 to 2016. The function and specification of the main systems of the liquid oxygen filling system, such as the storage tank, the drainage tank, the supply pumping system, the curved heat exchanger with liquid nitrogen, end valve block system, and umbilical connection, are presented.

• Journal of Animal Environmental Science
• /
• v.8 no.3
• /
• pp.129-134
• /
• 2002

This study was carried out to investigate the characteristic change of piggery slurry during the storage time and depth. The Piggery slurry was settled in a 10.0m diameter$\times$3.0m high storage tank for 6 months and then divided into three layers according to the storage time. The pollutants concentration, BODs(Biochemical Oxygen demand), CO $D_{Mn}$ (Chemical Oxygen demand) and SS(Suspended Solids) of the piggery slurry used in this study were 25,134, 15,840, 23,800mg/$\ell$, respectively. The initial fertilizer content of piggery slurry, N(Nitrogen), $P_2$ $O_{5}$(Phosphoric acid) and $K_2$O(Potassium oxide), were 0.69, 0.33, 0.40%, respectively. 6 months later, BO $D_{5}$, CO $D_{Mn}$ and SS of the Piggery slurry were 16,040, 8,098, 3,300mg/$\ell$ in top layer, 15,806, 8,309, 5,900mg/$\ell$ in middle layer and 39,530, 23,958, 51,000mg/$\ell$ in bottom layer, respectively. The fertilizer content of piggery slurry after 6 months, N, $P_2$ $O_{5}$ and $K_2$O, were 0.47, 0.07, 0.46% in top layer, 0.43, 0.08, 0.47% in middle layer and 0.60, 0.44, 0.40% in bottom layer, respectively. Consequently, in course of storage time, the pollutant concentration and fertilizer content were the highest in the bottom layer compared with the top and middle layer.