• 공업화학
• /
• 제17권4호
• /
• pp.335-342
• /
• 2006

금속 알루미늄의 낮은 환원전위는 전기화학적 산화반응을 통하여 알루미늄과 그 표면에 존재하는 산화막의 구조 및 성질의 변화를 일으킨다. 산성용액에서 알루미늄을 전기화학적으로 에칭하여 표면적을 확대시키고 중성의 용액에서 알루미늄 표면에 치밀한 유전체 산화막을 형성시켜 커패시터의 전극으로 이용하고 있다. 저온의 산성용액에서는 양극산화시 나노크기의 다공층 산화막이 형성되며, 나노구조체의 템플레이트로 사용되고 있다. 이와같은 알루미늄의 전기화학적 특성은 알루미늄을 새로운 기능성을 가진 재료로 변화시킴으로서 다양한 분야에서 응용될 것으로 기대된다.

• 폴리머
• /
• 제26권3호
• /
• pp.353-359
• /
• 2002

본 연구에서는 고강도 초음파를 이용하여 분자량이 다른 poly(ethylene oxide) (PEO)를 증류수에 분산시켜 초음파 가진(加振) 시간이 PEO의 성질에 미치는 영향을 조사하였다. 고강도 초음파는 PEO 수용액 상에서 동공 형성 및 파괴를 일으켜서 PEO 거대 라디칼을 형성하였으며 이로인하여 PEO 자체의 유변학적 성질, 화학 구조 그리고 용융 거동이 현저하게 변화되었다. 초음파 가진에 의하여 PEO의 용융 점도는 감소되었고, 물과 PEO 사슬에서 비롯된 여러 종류의 라디칼들의 상호 작용으로 말미암아 새로운 말단기들이 생성되었다. 아울러 분자량에 따라 상이한 용융 거동을 나타내었는데, 상대적으로 분자량이 큰 경우에는 가진되지 않은 PEO에 비하여 결정화 속도가 느려지고 용융 피크의 강도가 감소되는 특성을 나타내었다.

• Transactions on Electrical and Electronic Materials
• /
• 제14권4호
• /
• pp.216-220
• /
• 2013

The etching characteristics of indium zinc oxide (IZO) in $Cl_2/Ar$ plasma were investigated, including the etch rate and selectivity of IZO. The IZO etch rate showed non-monotonic behavior with increasing $Cl_2$ fraction in the $Cl_2/Ar$ plasma, and with increasing source power, bias power, and process pressure. In the $Cl_2/Ar$ (75:25%) gas mixture, a maximum IZO etch rate of 87.6 nm/min and etch selectivity of 1.09 for IZO to $SiO_2$ were obtained. Owing to the relatively low volatility of the by-products formation, ion bombardment was required, in addition to physical sputtering, to obtain high IZO etch rates. The chemical state of the etched surfaces was investigated with X-ray photoelectron spectroscopy. These data suggested that the IZO etch mechanism was ion-enhanced chemical etching.

• Bulletin of the Korean Chemical Society
• /
• 제35권11호
• /
• pp.3163-3168
• /
• 2014

Three kinds of lanthanum oxides ($La_2CO_3$) were synthesized from different methods and used as a catalyst in the transesterification of dimethyl carbonate (DMC) with glycerol for the synthesis of glycerol carbonate (GLC). Lanthanum oxide synthesized using a surfactant (S-La) showed a much higher GLC yield of 89.9% compared to other lanthanum oxides synthesized by calcination (C-La) and precipitation (P-La) at the reaction conditions of $90^{\circ}C$, DMC/glycerol = 2, and catalyst/glycerol = 5 wt %. The best catalyst was obtained when the surfactant/La weight ratio was 12. XRD study revealed that S-La has large amount of monoclinic and hexagonal $La_2O_2CO_3$ phases, which are assumed as active sites of the catalyst for the reaction.

• Carbon letters
• /
• 제9권2호
• /
• pp.108-114
• /
• 2008

We have demonstrated the feasibility of using electrospinning method to fabricate long and continuous composite nanofiber sheets of polyacrylonitrile (PAN) incorporated with zinc oxide (ZnO). Such PAN/ZnO composite nanofiber sheets represent an important step toward utilizing carbon nanofibers (CNFs) as materials to achieve remarkably enhanced physico-chemical properties. In an attempt to derive these advantages, we have used a variety of techniques such as field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM) and high resolution X-ray diffraction (HR-XRD) to obtain quantitative data on the materials. The CNFs produced are in the diameter range of 100 to 350 nm after carbonization at $1000^{\circ}C$. Electrical conductivity of the random CNFs was increased by increasing the concentration of ZnO. A dramatic improvement in porosity and specific surface area of the CNFs was a clear evidence of the novelty of the method used. This study indicated that the optimal ZnO concentration of 3 wt% is enough to produce CNFs having enhanced electrical and physico-chemical properties.

• Composites Research
• /
• 제29권4호
• /
• pp.132-137
• /
• 2016

Based on mussel-inspired polydopamine (PDA), a novel technique to fabricate carbon nanowire (CNW) arrays is presented for a possible use of porous carbon electrode in electrochemical energy storage applications. PDA can give more porosity and nitrogen-doping effect to carbon electrodes, since it has high graphitic carbon yield characteristic and rich amine functionalities. Using such outstanding properties, the applicability of PDA for electrochemical energy storage devices was investigated. To achieve this, the decoration of the CNW arrays on carbon fiber surface was performed to increase the surface area for storage of electrical charge and the chemical active sites. Here, zinc oxide (ZnO) nanowire (NW) arrays were hydrothermally grown on the carbon fiber surface and then, PDA was coated on ZnO NWs. Finally, high temperature annealing was performed to carbonize PDA coating layers. For higher energy density, manganese oxide ($MnO_x$) nanoparticles (NPs), were deposited on the carbonized PDA NW arrays. The enlarged surface area induced by carbon nanowire arrays led to a 4.7-fold enhancement in areal capacitance compared to that of bare carbon fibers. The capacitance of nanowire-decorated electrodes reached up to $105.7mF/cm^2$, which is 59 times higher than that of pristine carbon fibers.

• 대한화학회지
• /
• 제7권1호
• /
• pp.1-5
• /
• 1963

The thermal decomposition process of ammonium paratungstate $5(NH_4)_2O{\cdot}12WO_3{\cdot}5H_2O$ was analysed by the methods of thermogravimetric analysis, differential thermal analysis, quantitative analysis of the ammonia which is released during heating and X-ray powder diffraction in air and in vacuo. There are several endothermic peaks which indicate release of ammonia and exothermic peaks which indicate crystal growth and oxidation of decomposed prodects in air. After water is driven off the ammonia is released at intervals corresponding to the endothermic peaks. The highest temperature at which ammonia is released is about $420^{\circ}C$ in air and $480^{\circ}C$ in vacuo. In air the crystal structure of paratungstate is conserved up to a temperature of $300^{\circ}C$ at which the remaining ammonia is about 4 mols. At $320^{\circ}C$ the remaining ammonia becomes less than 2 mols and the paratungstate structure changes into the amorphous state. After that ${\gamma}$ oxide is produced and is oxidized to ${\alpha}$ oxide in the temperature range of 400-$500^{\circ}C$ in air. In vacuo however the endothermic peaks and structural changes occur at lower temperatures and the structure of ${\gamma}$ oxide is conserved up to temperatures higher than $500^{\circ}C$.

• Bulletin of the Korean Chemical Society
• /
• 제35권7호
• /
• pp.2072-2076
• /
• 2014

Sub-micrometer size gold particles were electrodeposited on a transparent fluorine-doped tin oxide (FTO) from acetonitrile solution containing $AuCl_4{^-}$ and tetramethylammonium tetraflouroborate (TMATFB) for detecting $NO_2{^-}$. A series of two-electron ($2e^-$) and one-electron ($1e^-$) reductions of the $AuCl_4{^-}-AuCl_2{^-}-Au$ redox systems were observed at FTO and a highly stable and homogeneous distribution of Au on FTO (Au/FTO) was obtained by stepping the potential from 0 to -0.55 V (vs. Ag/$Ag^+$). The Au/FTO electrode exhibited sufficiently high catalytic activity toward the oxidation of $NO_2{^-}$ with a detection limit (S/N = 3) and sensitivity of 2.95 ${\mu}M$ and 223.4 ${\mu}A{\cdot}cm^{-2}{\cdot}mM^{-1}$, respectively, under optimal conditions. It exhibited an interference-free signal for $NO_2{^-}$ detection with excellent recoveries from real samples.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2000년도 Proceedings of 5th International Joint Symposium on Microeletronics and Packaging
• /
• pp.109-109
• /
• 2000

Recently, carbon nanotube has been investigating for field emission display ( (FED) applications due to its high electron emission at relatively low electric field. However, the growing of carbon nanotube generally requires relatively high temperature processing such as arc-discharge (5,000 ~ $20,000^{\circ}C$) and laser evaporation (4,000 ~ $5,000^{\circ}C$) methods. In this presentation, low temperature growing of carbon nanotube by plasma enhanced chemical vapor deposition (PECVD) using nickel catalyst which is compatible to conventional FED processing temperature will be described. Carbon n notubes with average length of 100 run and diameter of 2 ~ $3\mu$ill were successfully grown on silicon substrate with native oxide layer at $550^{\circ}C$using nickel catalyst. The morphology and microstructure of carbon nanotube was highly depended on the processing temperature and nickel layer thickness. No significant carbon nanotube growing was observed with samples deposited on silicon substrates without native oxide layer. This is believed due to the formation of nickel-silicide and this deteriorated the catalytic role of nickel. The formation of nickel-silicide was confirmed by x-ray analysis. The role of native oxide layer and processing parameter dependence on microstructure of low temperature grown carbon nanotube, characterized by SEM, TEM XRD and R없nan spectroscopy, will be presented.

• 한국대기환경학회지
• /
• 제22권4호
• /
• pp.431-439
• /
• 2006

Catalytic oxidation of benzene, toluene and xylene (BTX) using regenerated metal oxide catalysts (ZnO-CuO, NiO, $Fe_2O_3$, ZnO, CrO) were investigated in a fixed bed flow reactor to evaluate their feasibility for the purpose of removing volatile organic compounds (VOCs). Four kinds of pre-treatment methods such as gas (air and hydrogen), acid aqueous solution, alkali aqueous solution and cleaning agent were used to find out the optimal regeneration conditions. The physico-chemical properties of the used and regenerated catalysts were characterized by BET and TPR (Temperature Programmed Reduction). The used catalysts showed high conversion ratio and the catalytic ability of toluene oxidation was in the order of ZnO-CuO>$Fe_2O_3$>NiO>ZnO>CrO. We found that the acid aqueous pre-treatment (0.1 N HNO$_3$) was the best way to enhance the catalytic activity of $Fe_2O_3$. In addition, air and hydrogen gas treatment were optimal for NiO and ZnO-CuO catalysts, respectively. Furthermore, the decomposition of BTX depends on the type of a catalyst and a gas molecule.