• Journal of The Korean Society of Agricultural Engineers
• /
• v.48 no.3
• /
• pp.3-8
• /
• 2006

The fractions of nitrogen were investigated in the soils of reclaimed and natural tidelands of southwest coastal area of Korea. The content of total-N varied to ranged form 619 to 5,534 mg/kg dry weight with a mean value of 1,857 mg/kg. The order of different fractions of nitrogen was as follows: Acid non-extractable-N > uncounted-N > acid extractable-N > ammonia-N > nitrate-N. The content of ammonia-N, acid extractable-N, and acid non-extractable-N showed highly negative correlations with pH. The content of acid extractable-N and ammonia-N showed highly positive correlation with clay content.

• Journal of the Korean Electrochemical Society
• /
• v.9 no.4
• /
• pp.151-157
• /
• 2006

A two-dimensional numerical model to study the performance of anode-supported flat-tube solid oxide fuel cell (SOFC) far the cross section of the cell in the flow direction of the fuel and air flows is developed. In this model a mass and charge balance, Maxwell-Stefan equation as well as the momentum equation by using, Darcy's law are applied in differential form. The finite element method using FEMLAB commercial software is used for meshing, discritization and solving the system of coupled differential equations. The current density distribution and fuel consumption as well as water production are analyzed. Experimental data is used to verify a predicted voltage-current density and power density versus current density to judge on the model accuracy.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.43 no.4
• /
• pp.40-48
• /
• 2011

In this study, we investigated the usability of new powdered additives in the paperboard industry. We manufactured the powdered additives from peanut husks and garlic stems by grinding. The chemical composition, particle size, particle size distribution, and particle shape were investigated to identify the basic properties of the powdered raw materials. To determine the effect of the powdered additives on paper properties, handsheets were prepared by adding the powdered additives to the pulp slurry. The chemical composition, such as the contents of holocellulose, lignin, and ash, showed similar values to those of other biomass materials. The particles of peanut husk powder were irregularly shaped, smaller, and had a broader particle size distribution than those of the garlic stem powder, which had the fibril form. The particles of the two powdered raw materials showed a positioning of expansion in the fiber network, resulting in increased bulk and a loss of strength. Handsheets containing garlic stem particles were stronger than handsheets containing peanut husk particles. Finally, the new powdered additives are beneficial to the bulk of paperboard.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.5
• /
• pp.1671-1678
• /
• 1996

In external chemical vapor deposition processes including VAD and OVD the distribution of flame-synthesized silica particles is determined by heat and mass transfer limitations to particle formation. Combustion gas flow velocities are such that the particle diffusion time scale is longer than that of gas flow convection in the zone of particle formation. The consequence of these effects is that the particles formed tend to remain along straight smooth flow stream lines. Silica particles are formed due to oxidation and hydrolysis. In the hydrolysis, the particles are formed in diffuse bands and particle formation thus requires the diffusion of SiCl$\_$4/ toward CH$\_$4//O$\_$2/ combustion zone to react with H$\_$2/O diffusing away from these same zones on the torch face. The conversion kinetics of hydrolysis is fast compared to diffusion and the rate of conversion is thus diffusion-limited. In the language of combustion, the hydrolysis occurs as a Burke-Schumann process. In selected conditions, reaction zone shape and temperature distributions predicted by the Burke-Schumann analysis are introduced and compared with experimental data available. The calculated centerline temperatures inside the reaction zone agree well with the data, but the calculated values outside the reaction zone are a little higher than the data since the analysis does not consider diffusion in the axial direction and mixing of the combustion products with ambient air. The temperatures along the radial direction agree with the data near the centerline, but gradually diverge from the data as the distance is away from the centerline. This is caused by the convection in the radial direction, which is not considered in the analysis. Spatial distribution of silica particles are affected by convection and diffusion, resulting in a Gaussian form in the radial direction.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.2
• /
• pp.447-452
• /
• 2013

In this study we report a new method for the synthesis of a silica monolithic column bed with bimodal pores (throughpores and mesopores). The template induced synthesis method was used to direct bimodal pores simultaneously instead of the usual post base-treating method. Block polymer Pluronic F127 was chosen as a dual-function template to form hierarchically porous silica monolith with both macropores and mesopores. This is a simplification of the method of monolithic column preparation. Poly(ethylene glycol) was used as a partial substitute for F127 can effectively prevent shrinkage during the monolith aging process without losing much surface area (944 $m^2/g$ to 807 $m^2/g$). More importantly, the resultant material showed a much narrower mesopore size (centered at 6 nm) distribution than that made using only F127 as the template reagent, which helps the mass transfer process. The solvent washing method was used to remove the remaining organic template, and it was proved to be effective enough. The new synthesis method makes the fabrication of the silica monolithic column (especially capillary column) much easier. All the structure parameters indicate that monolith PFA05 prepared by the above method is a good material for separation, with the merits of much higher surface area than usual commercial HPLC silica particles, suitable mesopore volume, narrow mesopore size distribution, low shrinkage and it is easily prepared.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.4
• /
• pp.1013-1030
• /
• 2018

Biodiesel is a fuel produced in the form of a fatty acid methyl ester by using raw materials such as animal fat, vegetable oil and its by-products, and is being seen as a biofuel that can replace petroleum energy. However unsaturated fatty acid methyl esters in biodiesel causes to oxidize during storage and distribution, resulting in poor fuel quality and corrosion of vehicle engine components. In this study, the influence of quality and oxidation characteristics of biodiesel on the oxidation stability is investigated and the evaluation method related it is described. We also propose a method to improve the drawback of oxidation stability in biodiesel.

• Journal of the Korean Chemical Society
• /
• v.22 no.5
• /
• pp.320-325
• /
• 1978

In order to elucidate the mechanism associated with the solvent extraction of uranium(VI) using DEPA and DPPA as extractant the uranium(VI) complexes formed during the solvent extraction were isolated and characterized by means of IR, NMR, chemical analysis and molecular weight determination. It has been found that uranium(VI) replaces the acidic hydrogen ions of the extractants DEPA and DPPA to form chelated polynuclear complexes, the molecular weight of U(VI)-DEPA complex being $2.1{\times}10^4$. The isolated U(VI)-DEPA complex has been found to be the same chemical species as is formed during the solvent extraction process. In case of DEPA the distribution coefficient of uranium is the largest of the pure aqueous uranium solution and is increasing for the acidic solutions in the order of $H_3PO_4.

• Journal of the Korean Ceramic Society
• /
• v.38 no.9
• /
• pp.822-828
• /
• 2001

Bayer process is based on the extraction of aluminium trihydroxide from bauxite. The process is operated with the several criteria such as primary crystal size, particle size distribution and yield etc.. In this study basing on the previous results, an investigation on the effect of chemical grade and smelting grade aluminium trihydroxide precipitation condition were undertaken. As a result, particle size was 42∼44${\mu}$m form chemical grade product and 74∼77${\mu}$m for smelting grade product. The yield and solubility by acid of chemical grade product was higher than smelting grade product. The attrition index of smelting grade product was lower than that of other commercial product because primary crystal size of the smelting grade product was small.

• Korean Journal of Materials Research
• /
• v.26 no.12
• /
• pp.751-756
• /
• 2016

Graphite was diffusion-bonded by hot-pressing to W-25Re alloy using a Ti interlayer. For the joining, a uniaxial pressure of 25 MPa was applied at $1600^{\circ}C$ for 2 hrs in an argon atmosphere with a heating rate of $10^{\circ}C\;min^{-1}$. The interfacial microstructure and elemental distribution of the W-25Re/Ti/Graphite joints were analyzed by scanning electron microscopy (SEM). Hot-pressed joints appeared to form a stable interlayer without any micro-cracking, pores, or defects. To investigate the high-temperature stability of the W-25Re/Ti/Graphite joint, an oxy-acetylene torch test was conducted for 30 seconds with oxygen and acetylene at a 1.3:1 ratio. Cross-sectional analysis of the joint was performed to compare the thickness of the oxide layer and its chemical composition. The thickness of W-25Re changed from 250 to $20{\mu}m$. In the elemental analysis, a high fraction of rhenium was detected at the surface oxidation layer of W-25Re, while the W-25Re matrix was found to maintain the initial weight ratio. Tungsten was first reacted with oxygen at a torch temperature over $2500^{\circ}C$ to form a tungsten oxide layer on the surface of W-25Re. Then, the remaining rhenium was subsequently reacted with oxygen to form rhenium oxide. The interfacial microstructure of the Ti-containing interlayer was stable after the torch test at a temperature over $2500^{\circ}C$.

• Clean Technology
• /
• v.12 no.2
• /
• pp.53-61
• /
• 2006

A PGSS (Particles from Gas Saturated Solutions) process designed to generate nano-particles using supercritical fluids has been conducted for the fabrication of Poly(lactide-co-glycolide) (PLGA) microparticles that encapsulate a protein drug. It is demonstrated that the polymer and the dry powder of a protein can be mixed under supercritical carbon dioxide conditions and that the protein component retains its biological activity. In this experiment, the mixture of polymer which is plasticized and dry powder protein was sprayed to form solid polymer that encapsulate the protein. It is found that supercritical fluid process give fine tuning of particle size and particle size distribution by simple manipulations of the process parameters. Porous particles were formed with irregular shape. Protein encapsulated in the polymer was found to have enzymatic activity without significant loss of its initial value.