• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1504-1506
• /
• 2004

Photovoltaic and wind power generation have an advantage of unpolluted and unlimited amount of energy resource. Since there is such an advantage in these energies, But photovoltaic system and wind system cannot always generate stable output with ever-changing weather condition. In this paper, the auxiliary power generator for hybrid system(photovoltaic 500[W], wind power generation 400[W]) was suggested. the auxiliary power generator that uses elastic energy of spiral spring to photovoltaic system was also added for present system. when output of photovoltaic system gets lower than 24[V], power was continuously supplied to load through the inverter by charging energy of spiral spring operates in DC generator.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.18-19
• /
• 2017

This paper shows the design of the high voltage capacitor charger which using a modified series parallel resonant converter. The used silicon carbide Metal-Oxide Semiconductor Field Effect Transistor (SiC MOSFET) is proper for the few hundred kHz of high switching frequency to overcome the bulk resonant inductor and snubber capacitors. Furthermore, to increase the amount of the charging current, three phase delta transformer is used as well as the secondary sides are connected in parallel. In this paper, the design procedure of the high voltage capacitor charger is suggested and the output power is verified by the experimental results with the rated resistor load.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.12
• /
• pp.113-118
• /
• 2020

Recently, eco-friendly electric motorcycles have been considered to replace aging gasoline motorcycles to reduce the amount of suspended fine dust in air. However, existing rechargeable battery-powered electric motorcycles have been found unacceptable by users because of their many limitations, such as long charging time, short travel distance per charge, and low driving speed. To overcome the drawbacks of conventional electric motorcycles, this paper proposes an exchangeable battery-powered electric motorcycle and a new frame shape for housing the exchangeable battery. The proposed frame is similar to that of current electric motorcycles; however, the shape and position of the saddle support, battery, and controller mount section are redesigned. The safety of the presented frame is verified through static and dynamic analyses using ABAQUS. In particular, the dynamic analysis is conducted under the most extreme condition among the various operating situations, thus confirming the robustness of the proposed frame design.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.25 no.3
• /
• pp.275-284
• /
• 2022

Linear Shaped Charge(LSC) is widely used as a separation system in the field of weapon system. However, there are some disadvantages that are charging lots of explosives due to lack of uniformity and having difficulties of the design of liner and explosives because of manufacturing process. In order to solve these problems, Precision Linear Shaped Charge(PLSC) that can design a liner independently and charge explosives uniformly has been developed. In this study, PLSC was designed to have a proper liner shape and amount of explosives, and the penetration test of PLSC with different stand-off distance from liner to target was conducted. On the basis of the penetration test results of PLSC, the numerical analysis method using AUTODYN was established and verified. The penetrative mechanism and characteristics of PLSC with targets of different materials was analyzed from experimental and numerical results.

• Journal of IKEEE
• /
• v.26 no.4
• /
• pp.710-713
• /
• 2022

In this paper, a Goertzel-based algorithm was proposed to calculate the amount of power by estimating the harmonic components generated during charging of the electric vehicle up to a very high order, allowing it to be applied to a low-cos electricity meter with low computing power. Using the proposed algorithm, it is verified through simulation for a simple example signal that even large-order harmonics can be sufficiently considered when wattage is measured.

• Design & Manufacturing
• /
• v.17 no.2
• /
• pp.62-69
• /
• 2023

In this study, we conducted a study on the optimization of injection molding conditions to minimize deformation of plastic product. The charging management system housing of the vehicle was selected as the research subject. Melting temperature, cooling temperature, packing time, and packing pressure were selected as the main factors expected to affect the deformation of molded products. Each main factor was divided into 5 levels. Optimization of injection molding conditions to minimize deformation was performed using the Taguchi Method. We performed an analysis of variance (ANOVA) to identify significant factors affecting the deformation of plastic product. In order to select injection molding conditions that minimize deformation of plastic products, injection molding analysis was additionally performed for insignificant factors. We then compared the deformation of the molded part before and after optimization. As a result of comparing the injection analysis results of the basic conditions and the injection analysis results of the optimal conditions, it was confirmed that the amount of deformation after optimization was improved by about 10.9%.

• Journal of the Society of Disaster Information
• /
• v.16 no.2
• /
• pp.392-401
• /
• 2020

Purpose: This study analyzes the operating characteristics of a lithium ion capacitor that can be used as a standby power supply in an emergency, and determines whether the standby power supply is abnormal even by measuring the voltage using a linear proportionality characteristic during charging and discharging. The aim is to provide an experimental basis that can be done. Method: As a method for this study, first, analyze the operation principle and characteristics of the existing backup power supply and lithium ion capacitor, and then measure the voltage of the lithium ion capacitor according to the configuration and system block diagram of the induction lamp used in the experiment. We proceed with the test of the measured value of discharge power for each voltage band to check the amount of power held by the battery and the operation test experiment using induction lamps. Results: Just by checking the charging voltage using the linear proportional characteristics of lithium ion capacitors, it provides a basis for accurately inferring the effective operating time of induction lamp lamps. Conclusion: In the event of a disaster, the lithium ion capacitor is used as a spare power supply for emergency induction lamps to prevent complete discharge of emergency induction lamps, to prevent the problem of performing normal operation of the standby power supply, and to use only a simple voltage measurement to reserve power. It was intended to suggest many uses for evacuation equipment application in the future by making it possible to check whether the device is abnormal.

• Journal of the Korean Magnetics Society
• /
• v.17 no.2
• /
• pp.65-70
• /
• 2007

In this paper, we composed the $LiFePO_4$ for the reversible use as the replacement material of the Li ion batteries and confirmed the good quality of the structure of the samples with the sintering temperature $675^{\circ}C,\;750^{\circ}C,\;and\;800^{\circ}C$ for 30 hours at nitrogen atmosphere. We also investigated the size of the particles through SEM picture and the change of the sintering temperature and the $Fe^{+3}$ content after charging the materials with 1 V, 160 mA and 3 V, 40 mA for 3 hours by Mossbauer spectroscopy. Also we can observe the increase on the $Fe^{+3}$ content at the charge condition and the increase of the amount ratio of the $Fe^{+3}$ ion only in sintering temperature $675^{\circ}C$ according to the increase of the electric charge. We cannot observe the change of the $Fe^{+3}$ ion in sintering temperature $800^{\circ}C$ after charging.

• Journal of Korean Society of Transportation
• /
• v.22 no.6
• /
• pp.101-108
• /
• 2004

The new transit fare in the Seoul Metropolitan is basically determined based on the distance-based fare system (DBFS). The total fare in DBFS consists of three parts- (1) basic fare, (2) transfer fare, and (3) extra fare. The fixed amount of basic fare for each mode is charged when a passenger gets on a mode, and it proceeds until traveling within basic travel distance. The transfer fare may be added when a passenger switches from the present mode to another. The extra fare is imposed if the total travel distance exceeds the basic travel distance, and after that, the longer distance the more extra fare based on the extra-fare-charging rule. This study proposes an algorithm for finding minimum fare route in DBFS. This study first exploits the link-label-based searching method to enable shortest path algorithms to implement without network expansion at junction nodes in inter-modal transit networks. Moreover, the link-expansion technique is adopted in order for each mode's travel to be treated like duplicated links, which have the same start and end nodes, but different link features. In this study, therefore, some notations associated with modes can be saved, thus the existing link-based shortest path algorithm is applicable without any loss of generality. For fare calculation as next steps, a mathematical formula is proposed to embrace fare-charging process using search process of two adjacent links illustrated from the origin. A shortest path algorithm for finding a minimum fare route is derived by converting the formula as a recursive form. The implementation process of the algorithm is evaluated through a simple network test.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.14 no.1
• /
• pp.56-69
• /
• 2021

In this paper, the PV system with a link to the commercial system needs some advantages like small capacity, high power factor, high reliability, low harmonic output, maximum power operation of solar cell, and low cost, etc. as well as the properties of inverter. To transfer the PV energy of photovoltaic power generation system to the system and load, it requires PCS in both directions. The purpose of this paper is to confirm the stable power supply through the load leveling by presenting the PCS considering ESS of photovoltaic power generation. In order to achieve these purpose, 5 step process of operation mode algorithm were used according to the solar insolation amount and load capacity and the controller for charging/ discharging control was designed. For bidirectional and effective energy transfer, the bidirectional converter and battery at DC-link stage were connected and the DC-link voltage and inverter output voltage through the interactive inverter were controlled. In order to prove the validity of the suggested system, the simulation using PSIM was performed and were reviewed for its validity and stability. The 3[kW] PCS was manufactured and its test was conducted in order to check this situation. In addition, the system characteristics suggested through the test results was verified and the PCS system presented in this study was excellent and stronger than that of before system.