• 동력기계공학회지
• /
• 제13권4호
• /
• pp.43-48
• /
• 2009

The purpose of this study is to show how to eliminate the noises and to obtain the data related with the relationship between AE signal characteristics and mechanical behaviors for the pressure vessel steel. Various kinds of noises are introduced into the AE data in the course of experiments. Accordingly, real AE data have to be obtained after tests. AE test was carried out under four point bending load. Among AE signals, counts and signal strength are used to find out the differences of AE characteristics between the basemetal and weldment. After tests, this paper shows the procedures of filtering the noises against basemetal of the pressure vessel steel to obtain the real data around crack tip. Relationships between plastic zone size and cumulative AE counts are shown also. AE signals were absent within an elastic region, regardless of the specimens. Most of AE signals are produced in the process of plastic deformation. The deformation and fracture modes of basemetal and weldment are quiet different.

• 한국세라믹학회지
• /
• 제45권1호
• /
• pp.75-81
• /
• 2008

In this study, machining characteristics of AIN-hBN composites were evaluated in end-milling process. As a first step, AIN-hBN composite specimens with various hBN contents were prepared using hot press method. Material properties of the composites, such as relative density, Young's modulus and fracture toughness, were measured and compared. Then, a series of end-milling experinients were performed under various cutting conditions by changing cutting speed, depth-of-cut and feed rate. Cutting force variations were measured using a tool dynamometer during the cutting experiments. Machined surfaces of the specimens were observed using SEM and a surface pro filer to investigate the surface integrity changes. The cutting force decreased with an increases of hBN content. The cutting process was almost impossible for monolithic AIN, owing to severe chipping. In contrast, at high content of hBN, surface damage and chipping decreased, and better surface roughness can be obtained.

• 한국전산구조공학회논문집
• /
• 제17권4호
• /
• pp.443-449
• /
• 2004

최근 콘크리트 균열선단에서 균열의 발생을 억제하거나 균열 발생시 균열폭을 제어하고 일정부분 하중저항 능력을 향상시킬 목적으로 다양한 형태의 강섬유(Steel Fiber)를 혼입하는 방법이 개발되어 사용되고 있다. 강섬유 보강 철근콘크리트보(SFRC; Steel Fiber Reinforced Concrete)의 복잡한 파괴역학적 성질에 의한 불확실성 통이 내재되어 있다. 본 연구에서는 SFRC보의 불확식성을 고려하는 신뢰성 해석을 수행하였다. 이를 위해 강도 한계상태모형을 제시하였고, 한계상태함수에 포함된 각종 확률변수들에 대한 통계적 특정값을 국내외 관련 문헌을 근거하여 수집, 제시하였다. 향후 추가적인 관련정보가 수집되면 보다 개선된 통계적 특성값을 제공 할 수 있도록 Blayseian Updating 기법을 사용하여 실험결과로부터 불확실성을 개선하는 과정을 제시하였다. 뿐만 아니라 피로신뢰성의 해석을 위해 피로파괴확률식을 제안하고 필요한 통계적 특성 값을 제시하였다.

• 한국정밀공학회지
• /
• 제27권4호
• /
• pp.79-86
• /
• 2010

Mechanical structures with power sources experience repeated force produced by motors. In result, the life of the pipes reduces and ultimately, the pipes collapse. Such pipes are formed into several shapes and particularly, the U-shape pipe is damaged frequently. In most cases, the U-shape pipe is made with a straight pipe by complicated bending work. During this work process, plastic deformation of the pipe produces residual stress in the pipe. This residual stress significantly affects the fracture behavior of the pipe and induces the change of the stress ratio (min. stress/Max. stress = R). For this reason, residual stress has to be evaluated. In this paper, the residual stress of a U-shaped pipe was evaluated by FEM analysis. In addition, fatigue tests of the U-shaped pipe were performed by using a uniaxial fatigue testing machine. The results of the fatigue test were modified with the results of FEM (Finite Element Method) analysis for residual stress. The modified fatigue test results of the U-shaped pipe were compared with those of a straight pipe.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1911-1915
• /
• 2003

Today optical communication industry is developed; demand of optical communication part is increased. ZrO$_2$ ceramic ferrule is very significant part which determines transmission efficiency and quality of information in the optical communication part by connector of optical fibers. Being different from metal grinding, material removal through brittle fracture plays an important role in ZrO$_2$ ceramic grinding. Most of ZrO$_2$ ceramic ferrule processes are grinding which request high processing precision. Particularly, concentricity and cylindricity of inner and outer diameter are very important. The co-axle grinding process of ZrO$_2$ ceramic ferrule is to make its concentricity all of uniform before centerless grinding. Surface integrity of ZrO$_2$ ceramic ferrule is affected by grinding conditions, and equipment. In this study, surface integrity of workpiece according to such as a change of grinding wheel speed, feed rate, regulating wheel speed and grinding force is investigate to improve the concentricity and roundness of ZrO$_2$ ceramic ferrule from many experiments. Thus, if possible be finding highly efficient and quality grinding conditions.

• 소성∙가공
• /
• 제15권8호
• /
• pp.609-614
• /
• 2006

Micro-alloyed steels(MA steels) for cold forging was developed to replace the usual quenched and tempered steel. MA steels have several advantages over the conventional quenched and tempered carbon steels. First of all, energy consumption could be lowered due to the elimination of spherodizing annealing and quenching/tempering heat treatment. Also, bending during quenching could be avoided when MA steels are applied for manufacturing of long fastener parts. However, larger amount of load is exerted on the dies compared than in the case of conventional mild steels, which might lead to the earlier fracture of dies, when MA forging steels are applied in forging practice. Therefore, die lift could be a critical factor to determine whether HA forging steels could be widely applied in cold forging practice. In the present study, authors have investigated the forging characteristics of non-heat treated micro-alloyed steel by using a series of experimental and numerical analyses. Firstly, microstructural features and its effect on the deformation behavior have been studied. Numerical analysis has been done on the forging of guide rod pin to investigate for the optimization of forging process and die stress prediction.

• Smart Structures and Systems
• /
• 제18권3호
• /
• pp.525-540
• /
• 2016

The CFRP-confined circular concrete-filled steel tubular column is composed of concrete, steel, and CFRP. Its failure mechanics are complex. The most important difficulties are lack of an available method to establish a relationship between a specific damage mechanism and its acoustic emission (AE) characteristic parameter. In this study, AE technique was used to monitor the evolution of damage in CFRP-confined circular concrete-filled steel tubular columns. A fuzzy c-means method was developed to determine the relationship between the AE signal and failure mechanisms. Cluster analysis results indicate that the main AE sources include five types: matrix cracking, debonding, fiber fracture, steel buckling, and concrete crushing. This technology can not only totally separate five types of damage sources, but also make it easier to judge the damage evolution process. Furthermore, typical damage waveforms were analyzed through wavelet analysis based on the cluster results, and the damage modes were determined according to the frequency distribution of AE signals.

• 대한조선학회논문집
• /
• 제41권6호
• /
• pp.75-83
• /
• 2004

Ice rubble pieces broken by the bow impact load and side hull of an icebreaking vessel usually pass along the ship's bottom hull and may hit the propeller/rudder or other stern structures causing serious damage to ship's hull . Therefore it is important to estimate the size of broken ice pieces during the icebreaking process. The dynamic interaction process of icebreaker with infinite ice sheet is simplified as a wedge type beam of finite length supported by elastic foundation. The wedge type ice beam is leaded with vertical impact forces due to the inclined bow stem of icebreaking vessels. The numerical model provides locations of maximum dynamic bending moment where extreme tensile stress arises and also possible fracture occurs. The model can predict a failure length of broken ice sheet given design parameters. The results are compared to Nevel(1961)'s analytical solution for static load and observed pattern of ice sheet failure onboard an icebreaker. Also by comparing computed failure length with the characteristic length, the meaning of ice rubble sizes is discussed.

• 공업화학
• /
• 제31권5호
• /
• pp.514-519
• /
• 2020

흑연 소재는 높은 구조적 안정성 및 낮은 가격으로 리튬 이차전지 음극소재로 이용되고 있다. 또한, 탄소 소재의 낮은 속도 특성을 개선하려는 탄소 코팅 연구가 활발히 진행되고 있다. 탄소 코팅은 화학적 반응을 이용하는 CVD 코팅, 용매를 사용하는 습식 코팅, 기계적 충돌에 의한 건식 코팅으로 나뉜다. 본 논문에서는 습식 코팅 공정에서 사용 용매에 따라 탄소 전구체(피치)의 일부만 사용될 수 있는 문제와 용매 제거에 의한 환경 문제를 해결하고자 건식 공정인 고속 분쇄/코팅 공정을 이용하여 리튬 이차전지 음극용 탄소 소재를 제조하였다. 침상 코크스와 피치의 무게비는 8 : 2 wt.%으로 하고, 고속 분쇄/코팅 공정을 이용하여 침상 코크스의 분쇄와 피치의 코팅을 통한 구상화를 진행하였을 때, 침상 코크스의 모서리 면이 피치로 코팅되는 것을 확인하였다. 이 소재를 2400 ℃ 고온 열처리를 진행한 결과 피치 코팅되지 않은 소재와 비교하여 초기용량과 효율은 큰 차이를 보이지 않았으나, 10C/0.1C 속도 특성에서 41.8%의 성능이 향상되었다. 고속 분쇄/코팅 공정을 통해 제조된 소재는 고속 방전용 리튬 이차전지 음극 소재에 사용될 수 있을 것으로 생각된다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제41권1호
• /
• pp.118-124
• /
• 2017

본 연구대상 디젤기관의 연접봉 볼트, 크랭크 핀 베어링 볼트 등의 손상원인을 조사 분석하기 위하여 수행한 현장검사, 파손부에 대한 시험 및 고찰, 참고문헌 및 연구자의 경험 등을 통하여 다음과 같은 결론을 얻었다. 파손된 크랭크 핀 베어링 볼트는 연접봉 볼트보다 늦게 파손된 것으로 추정된다. 파손된 연접봉 볼트는 충격적인 하중에 의해서 취성파괴된 것이 아니고, 비정상적인 반복하중(예를 들어 체결 볼트의 풀림 등)에 의해서 피로파괴가 되었다는 것을 그 파단면의 모습을 통하여 알 수 있다. 파손된 연접봉 볼트용 U 너트는 윤활유(고착방지제)의 부적절한 사용, 각 실린더와 연접봉 별로 구분되어 사용되지 않았던 것 등으로 인하여 표면 상태가 불량하게 되었고, 이것은 연접봉 볼트의 파손사고에 영향을 미쳤을 가능성이 있다고 할 수 있다. 그리고 파손된 국내 제작품인 연접봉 볼트와 크랭크 핀 베어링 볼트의 기계적 성질, 전조공정 등은 해당 볼트의 설계요건에 적합하다고 할 수 있다.