• Journal of the Korea Convergence Society
• /
• v.13 no.4
• /
• pp.287-292
• /
• 2022

In this paper, the stochastic distribution of the springback amount is investigated for the stamping process of a U-channel shaped-product with ultra-high strength steel. Using the reliability-based design optimization technique (RBDO), stochastic distribution of process parameters is considered in the analysis including material properties and process variation. Quantification of the springback scatters is carried out with the statistical analysis method according to the material strength. It is found that the scattering amount of springback decreases while the amount of springback increases as the tensile strength of the blank material increases, which is investigated by analyzing the strain and stress distribution of the punch and die shoulder. It is noted that the proposed scheme is capable of predicting and responding to the unavoidable scattering of springback in the sheet metal forming process.

• Ocean and Polar Research
• /
• v.44 no.1
• /
• pp.13-27
• /
• 2022

The Yeongsan River estuary was altered by a sea dike built in 1981 and the sluice gates in the dike were extended recently in 2014. The construction has caused changes in water properties and hydrodynamics and also produced disturbances including hypoxia and algal blooms. We analyzed the water quality and chlorophyll-a data (2009-2018) collected seasonally at 3 stations (Sts. 1-3) along the channel of the estuary by the Marine Environmental Monitoring System. Variations in water quality and chlorophyll-a (an index of phytoplankton biomass) were examined and their stressors were also identified by statistics including correlation and multivariate principal component analyses (PCA). The water quality was mainly affected by freshwater discharge from the dike. Salinity, nutrients and chlorophyll-a were especially affected by the discharge and the effect enhanced during summer and at the upper region near the sea dike decreasing downstream. Three factors were extracted for each station in the PCA accounting for 66.07-72.42% of the variations. The first was an external factor associated with freshwater discharge and the second and third were seasonal or biological factors. The results indicate that the water quality is more affected by short-termed and episodic events such as freshwater discharge than seasonal events and the influence of freshwater discharge on water quality is more extensive than that previously reported. This suggests that the boundary of the estuary should be extended to take into account the findings of this study and a management strategy linked to the freshwater zone is required to manage the integrity and water quality of the Yeongsan River estuary.

• Steel and Composite Structures
• /
• v.44 no.1
• /
• pp.33-47
• /
• 2022

This paper presents a finite element model for predicting the monotonic behaviour of bolted endplate joints connecting steel-concrete composite walls and steel beams. The demountable Hollo-bolts are utilised to facilitate the quick installation and dismantling for replacement and reuse. In the developed model, material and geometric nonlinearities were included. The accuracy of the developed model was assessed by comparing the numerical results with previous experimental tests on hollow/composite column-to-steel beam joints that incorporated endplates and Hollo-bolts. In particular, the Hollo-bolts were modelled with the expanded sleeves involved, and different material properties of the Hollo-bolt shank and sleeves were considered based on the information provided by the manufacture. The developed models, therefore, can be applied in the present study to simulate the wall-to-beam joints with similar structural components and characteristics. Based on the validated model, the authors herein compared the behaviour of wall-to-beam joints of two commonly utilised composite walling systems (Case 1: flat steel plates with headed studs; Case 2: lipped channel section with partition plates). Considering the ease of manufacturing, onsite erection and the pertinent costs, composite walling system with flat steel plates and conventional headed studs (Case 1) was the focus of present study. Specifically, additional headed studs were pre-welded inside the front wall plates to enhance the joint performance. On this basis, a series of parametric studies were conducted to assess the influences of five design parameters on the behaviour of bolted endplate wall-to-beam joints. The initial stiffness, plastic moment capacity, as well as the rotational capacity of the composite wall-to-beam joints based on the numerical analysis were further compared with the current design provision.

• Human Ecology Research
• /
• v.61 no.3
• /
• pp.389-399
• /
• 2023

Sustainable fashion products have different characteristics from typical fashion products. Therefore, this study focuses on shoes while exploring the expansion and development of sustainable fashion consumption as well as consumers' perceptions of the sustainability approaches practiced by shoe companies. In-depth interviews were conducted with 24 consumers, who had purchased sustainable shoes, in order to understand their purchase decision-making process and consumption characteristics, using the seven stages of the EBM model. In the "need recognition" stage, the survey participants' social background and family influences were categorized as macro factors, while their personal background influences were categorized as micro factors. In the "evaluation of alternatives" stage, participants reconfirmed whether or not to make a purchase based on the product's properties, such as price, brand value, and offered services. In the "purchase" stage, participants' purchase channels were determined according to their preferences as well as the selection pattern they followed until the final purchase within the chosen channel. In the "consumption" stage, the start of product ownership coincides with the start of using the products after making a purchase. In the "post-purchase assessment" stage, higher positive experiences led to a higher repurchase intention of sustainable shoes, while negative experiences caused participants to defer consumption and made them experience a sense of guilt for failing to consume sustainably. During the "post-purchase behavior" stage, which focused on the categories that the customers prioritized, many participants spread information about sustainable fashion to specific individuals through active online WOM behavior.

• Composites Research
• /
• v.36 no.3
• /
• pp.217-223
• /
• 2023

In this work, the preparation and its oil adsorption behavior of polyacrylonitrile-based carbon nanofiber sponge were investigated. The prepared carbon sponges showed excellent selective oil adsorption in the mixture of water and oil, and the adsorption capacity of reused carbon nanofiber sponge was also investigated. Further, carbon nanofiber sponge adsorbent with internally structured channel showed fast oil adsorption behavior due to a capillary phenomenon. After use, sponge adsorbent was heat-treated at 800℃ under N² and studied the possibility of a sensor for electrochemical detection of 4-aminophenol.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.6B
• /
• pp.607-615
• /
• 2010

Vegetation drag tends to raise water level by retarding the flow. Previous studies have focussed on either the vertical structure modeling or the one-dimensional modeling, which can hardly be used to simulate the vegetative streams in practical engineering. Therefore, this paper presents a two-dimensional numerical model based on the depth-averaged flow equations. Vegetation drags are reflected in the flow equations, assuming non-flexible rigid cylinders. For validations, flow properties measured in both rectangular and compound channels are compared with simulated data, showing good agreement. Then, the model is applied to a reach in the Han River and the impact of floodplain vegetation on the flow is investigated.

• Journal of The Geomorphological Association of Korea
• /
• v.27 no.4
• /
• pp.71-88
• /
• 2020

This study modified the properties and boundaries of the inland wetland types through the structural edit of the National Wetland DB, and analyzed the characteristics of the different land cover by area and the entire inland wetlands of South Korea. The inland wetlands of the Gangwon Basin had a small area of waters. In addition, the ratio of natural barren was high, reflecting the characteristics of the upper reaches of the large river in the east and west part of Gangwon Province. The Geum River Basin had a high percentage of aggregate land due to the development of large alluvial land, and the ratio of artistic barren was low, so various ecosystem service of wetland elements were distributed evenly. The Nakdong River Basin had a high proportion of waters as water level in the channel rose due to the installation of 4 Major Rivers Beam, and the ratio of Natural barren was low. Moreover, the water level of the main attributes flowing into the Nakdong River drainage system was not high, so the ratio of vegetation concentration was high. The Yeongsan River Basin showed that Waters had the high proportion. And the distribution of Natural barrens represented differently according to the Yeongsan River Basin and the Seomjin River Basin. Finally, Sand and Gravels supplied to rivers during precipitation were deposited in the main stream of the Han River Basin, and the differences between the side and high side was large in the area, reflecting the characteristics of the mouth of a river, so the Natural barren of Clay was distributed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.6
• /
• pp.588-593
• /
• 2023

The advantage of OTFT technology is that large-area circuits can be manufactured on flexible substrates using a low-cost solution process such as inkjet printing. Compared to silicon-based inorganic semiconductor processes, the process temperature is lower and the process time is shorter, so it can be widely applied to fields that do not require high electron mobility. Materials that have utility as electrode materials include carbon that can be solution-processed, transparent carbon thin films, and metallic nanoparticles, etc. are being studied. Recently, a technology has been developed to facilitate charge injection by coating the surface of the Al electrode with solution-processable titanium oxide (TiOx), which can greatly improve the performance of OTFT. In order to commercialize OTFT technology, an appropriate method is to use a complementary circuit with excellent reliability and stability. For this, insulators and channel semiconductors using organic materials must have stability in the air. In this study, carbon-doped Mo (MoC) thin films were fabricated with different graphite target power densities via unbalanced magnetron sputtering (UBM). The influence of graphite target power density on the structural, surface area, physical, and electrical properties of MoC films was investigated. MoC thin films deposited by the unbalanced magnetron sputtering method exhibited a smooth and uniform surface. However, as the graphite target power density increased, the rms surface roughness of the MoC film increased, and the hardness and elastic modulus of the MoC thin film increased. Additionally, as the graphite target power density increased, the resistivity value of the MoC film increased. In the performance of an organic thin film transistor using a MoC gate electrode, the carrier mobility, threshold voltage, and drain current on/off ratio (I_on/I_off) showed 0.15 cm²/V·s, -5.6 V, and 7.5×10⁴, respectively.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.27 no.1
• /
• pp.43-50
• /
• 2024

Large planar military antenna boasts a range of electrical components, including TRA(Transmit-Receive Assembly), signal processors, etc. which engage in computations and calculations. These processes generate a significant amount of heat, leading to unforeseen consequences for the equipment. To mitigate these adverse effects, it's imperative to implement a cooling system that can effectively reduce heat-related issues. Given the antenna's intricate nature and the multitude of components it houses, a two-step estimation process is necessary. The first step involves a comprehensive model calculation to determine the total flow characteristics, while the second step entails a thermal analysis of individual TRA set. In this study, we depicted an antenna set using simplified 3D models of its components, considering their material and thermal properties. The sequential analysis process facilitated the calculation of branched flow rates, providing insights into the individual TRA. This approach also allowed us to design a cooling system for the TRA set, assessing its thermal stability in high-temperature environments. To ensure the optimal performance of TRA, breaking down the analysis into stages based on the cooling system's structure can assist operators in predicting numerical results more effectively.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.24 no.1
• /
• pp.16-25
• /
• 2012

To calculate the total mass flux that change in dry and flood season in the Yeomha Channel of Gyeonggi Bay, the 13 hour bottom tracking observation was performed from the southern extremity. The value of the total mass flux(Lagrange flux) was calculated as the sum of the Eulerian flux value and stroke drift value and the tidal residual flow was harmonically analyzed through the least-squares method. Moreover, the average during the tidal cycle is essential to calculate the mass flux and the tidal residual flow and there is the need to equate the grid of repeatedly observed data. Nevertheless, due to the great differences in the studied region, the number of vertical grid tends to change according to time and since the horizontal grid differs according to the transport speed of the ship as a characteristic of the bottom tracking observation, differences occur in the horizontal and vertical grid for each hour. Hence, the present study has vertically and horizontally normalized(sigma coordinate) to equate the grid per each hour. When compared to the z-level coordinate system, the Sigma coordinate system was evaluated to have no irrationalities in data analysis with 5% of error. As a result of the analysis, the tidal residual flow displayed the flow pattern of sagging in the both ends in the main waterway direction of dry season. During flood season, it was confirmed that the tidal residual flow was vertical 2-layer flow. As a result of the total mass flux, the ebb properties of 359 cm/s and 261 cm/s were observed during dry and flood season, respectively. The total mass flux was moving the intertidal region between Youngjong-do and Ganghwa-do.