• 한국분무공학회지
• /
• 제24권3호
• /
• pp.105-113
• /
• 2019

In this paper, a study of Urea-SCR System for Dosing Injector for responding to enhanced environmental regulations has been conducted. There is a limit to the experimental approach due to the structural characteristics of the injector. In order to overcome this problem, The analysis was performed assuming unsteady turbulent flow through computational fluid analysis and the internal flow characteristics of the injector were analyzed. By changing the nozzle shape of the injector, the performance factors of the swirl injector by shape were selected and compared. The design parameters were modified by changing the diameter of the nozzle at a constant ratio compared to the base model. Swirl coefficient, outlet mass flow, and sac volume were selected as performance parameters of the injector. The Conv. model to which the taper was applied showed the dominance in mass flow rate, discharge coefficient and swirl because of the smooth fluid flow by shape. Swirl coefficient, outlet mass flow, and sac volume were selected as performance parameters of the injector. As a result of the comparison coefficient derivation with those performance parameters for comparing the performance of the model-specific injector, the Conv-140 model with the nozzle diameter expanded by 140% showed the best value of the comparison coefficient.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2004년도 춘계학술대회 논문집
• /
• pp.195-199
• /
• 2004

The most important role of photosensor is to measure on exact workplan illuminance of room when daylight responsive dimming systems are used. The shape of most optimal photosensor must be able to measure exact luminous flux without changing setting position corresponding to the change of room situations. That is, shape and positioning of optimal photosensor should be corresponded to the optimal luminous flux measurement.

• 한국기계기술학회지
• /
• 제13권3호
• /
• pp.1-6
• /
• 2011

In order to find better performance of heat sink, in this research, different cases were analysed by changing number of slots and shape of fins. Round shape fins which have wide surface showed 24% better heat transfer rate than vertical fins. There were not big discrepancies between 1 slot and 2 slots fins. Consequently, for better performance of heat sink, developments for widening surface and better material for high heat transfer rate are needed.

• 한국안전학회지
• /
• 제27권3호
• /
• pp.28-35
• /
• 2012

We investigated the breakdown patterns of silica glass under the various impacts by forensic scientific analysis. The impacts were chosen by thermal and projectiles impact stress. Thermal impacts under the fire were constructed by changing the position of the flame with gas torches. Physical impacts were constructed with the projectiles of slingshots and rifles by changing the size of the projectiles at the surfaces and the initial distance. Also we identified incident angles of the projectiles by analysis of the punching portion at the glass surface. Under the thermal impacts, the breakdown patterns were various by changing the position of the flame. Especially, the configuration of breakdown patterns had radial shape with the position of the flame at the center of the glass sheet. Under the physical impacts by the projectiles, the breakdown patterns had always radial shape.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.865-868
• /
• 2002

This study investigated the shape deformation of ball projectile(5.56mn) under the low energy impact by the use of the drop weight impact tester. ball projectile(5.56mm) consisted of the copper face with a lead core. The impact conditions were changed with the variations of the mass and the drop height of the impact tup. Shape deformation of ball projectile(5.56mm) after low velocity impact was measured using a video microscope and CCD camera. The test result showed that impact energy by changing of drop height of the impact tup affected shape deformation of ball projectile(5.56mm). So, it is important to study the relativity between shape deformation of ball projectile(5.56mm) and ballistic protection of plate(such as hybrid composite laminates) under the high velocity impact.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.172-175
• /
• 2007

The Performance of a PEMFC stack is strongly dependent on the uniform reactants distribution on MEA. The uniform distribution can be achieved by flow-field pattern and manifold design optimized to satisfy operating conditions. This paper investigates uniform reactants distribution in channels by changing manifold shape and inlet mass flow rate. Typical U and Z shape and modified U and Z shape manifolds with buffer zone were designed. To check the uniform reactants distribution, standard deviation of mass flow rate was compared. The numerical results show that the inlet mass flow rate, inlet shape, and manifolds shape are critical factor for uniform distribution.

• 한국HCI학회:학술대회논문집
• /
• 한국HCI학회 2009년도 학술대회
• /
• pp.56-61
• /
• 2009

공간 스케치에서 그리고자 하는 모델의 종류에 따라 효율적인 입력장치가 다르게 정의될 수 있다. 범용적인 공간 스케치 시스템에서 다양한 형태의 완드 형태를 지원하여 그리고자 하는 모델 또는 모델의 특정 부분에 적합한 완드의 형태를 바꾸어 가며 사용함으로써 효율적인 공간 스케치를 수행할 수 있다. 모델을 스케치 하는 중에 완드의 형태를 변형하기 위하여 기존의 메뉴를 사용하지 않고, 완드의 자세 또는 경로를 조절함으로써 완드의 타입과 형태를 바꾸는 완드 스타일을 제안하였으며, 완드의 입력 데이터를 격자 기반의 드로잉 기법을 사용하여 공간 스케치 시스템에 적용하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.128-133
• /
• 2002

The main obstacle to high track density in HDD is the structural resonances of the suspension. The most critical mode is sway mode and second torsion mode, when a data is read and written. It is common fact that the effect of two modes is smaller when a thickness is bulky. But the stiffness of suspension is smaller, the slider can follow a disk better. Because these two fact are reciprocal, a compromise is needed. So we investigated another method to improve band width without changing of the thickness of suspension but with changing of the shape. In this paper, we use two method - Sensitivity analysis and SIP using ADS. And we obtained the optimized value close to target value.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.319.2-319
• /
• 2002

The main obstacle to high track density in HDD id the structural resonances of the suspension. The most critical mode is sway mode and second torsion mode, when a data is read and written. It is common fact that the effect of two modes is smaller when a thickness is bulky. But the stiffness of suspension is smaller, the slider can follow a disk better. Because these two fact are reciprocal, a compromise is needed. So we investigated another method to improve band width without changing of the thickness of suspension but with changing of the shape. (omitted)

• Coupled systems mechanics
• /
• 제8권6호
• /
• pp.473-488
• /
• 2019

The present work is the study of mechanical behavior due to variation of the geometrical parameters in the core of the sandwich honeycomb panel. This study has allowed us to increase or decrease the strains and stresses of the panel, in changing the angle of alveolus, as explained and described below. In taking into consideration the results obtained previously to improve the mechanical properties and increase the adhesion of different parts of the panel, without changing the adhesive, we have conceived two new models, in increasing the contact surfaces in boundary of each part of the panel and giving a conical hexagonal shape in his corp.