• Smart Structures and Systems
• /
• v.19 no.3
• /
• pp.269-277
• /
• 2017

Recently, there has been significant interest in structural health monitoring for civil engineering applications. In this research, a specially designed tendon, proposed by embedding FBG sensors into the center king cable of a 7-wire strand tendon, was applied for long-term health monitoring of tensile forces on a ground anchor. To make temperature independent sensors, the effective temperature compensation of FBG sensors must be considered. The temperature sensitivity coefficient ${\beta}^{\prime}$ of the FBG sensors embedded tendon was successfully determined to be $2.0{\times}10^{-5}^{\circ}C^{-1}$ through calibrated tests in both a model rock body and a laboratory heat chamber. Furthermore, the obtained result for ${\beta}^{\prime}$ was formally verified through the ground temperature measurement test, expectedly. As a result, the ground temperature measured by a thermometer showed good agreement compared to that measured by the proposed FBG sensor, which was calibrated considering to the temperature sensitivity coefficient ${\beta}^{\prime}$. Finally, four prototype ground anchors including two tension ground anchors and two compression ground anchors made by replacing a tendon with the proposed smart tendon were installed into an actual slope at the Yeosu site. Tensile forces, after temperature compensation was taken into account using the verified temperature sensitivity coefficient ${\beta}^{\prime}$ and ground temperature obtained from the Korean Meteorological Administration (KMA) have been monitored for over one year, and the results were very consistent to those measured from the load cell, interestingly.

• Korean Journal of Environmental Agriculture
• /
• v.6 no.2
• /
• pp.66-72
• /
• 1987

Sensitivity of the three freshwater fish, Cyprinus carpio, Oryzias latipes (wildtype indigenous to Korea), and O. latipes (Japanese killifish) to 30 pesticide formulations were studied in terms of 48 hr $LC_{50}$ determined with the static method. The correlation between C. carpio and O. latipes (Japanese killifish) was higher than that between C. carpio and O. latipes with correlation coefficients of 0.89 and 0.80, respectively. The sensitivity of O. latipes and O. latipes (Japanese killifish) to pesticides showed very high correlation with a coefficient of 0.93. Therefore, it is suggested that the acute toxicity data concerning O. latipes (Japanese killifish) could represent those C. carpio or O. latipes which are indigenous species in Korea. Also, it is found that the present protocol for the toxicity test with carp in Korea has difficulties in maintaining the proper concentration of dissolved oxygen in the test chamber because of the abrupt decrease of dissolved oxygen to 2mg/l, which is not acceptable according to general guidelines of foreign countries.

• Korean Journal of Materials Research
• /
• v.22 no.7
• /
• pp.358-361
• /
• 2012

Co and Ni as catalysts in $SnO_2$ sensors to improve the sensitivity for $CH_4$ gas and $CH_3CH_2CH_3$ gas were coated by a solution reduction method. $SnO_2$ thick films were prepared by a screen-printing method onto $Al_2O_3$ substrates with an electrode. The sensing characteristics were investigated by measuring the electrical resistance of each sensor in a chamber. The structural properties of $SnO_2$ with a rutile structure investigated by XRD showed a (110) dominant $SnO_2$ peak. The particle size of the $SnO_2$:Ni powders with Ni at 6 wt% was about 0.1 ${\mu}m$. The $SnO_2$ particles were found to contain many pores according to a SEM analysis. The sensitivity of $SnO_2$-based sensors was measured for 5 ppm of $CH_4$ gas and $CH_3CH_2CH_3$ gas at room temperature by comparing the resistance in air to that in the target gases. The results showed that the best sensitivity of $SnO_2$:Ni and $SnO_2$:Co sensors for $CH_4$ gas and $CH_3CH_2CH_3$ gas at room temperature was observed in $SnO_2$:Ni sensors coated with 6 wt% Ni. The $SnO_2$:Ni gas sensors showed good selectivity to $CH_4$ gas. The response time and recovery time of the $SnO_2$:Ni gas sensors for the $CH_4$ and $CH_3CH_2CH_3$ gases were 20 seconds and 9 seconds, respectively.

• Journal of Navigation and Port Research
• /
• v.32 no.10
• /
• pp.793-798
• /
• 2008

This paper presents a design of RFID(Radio Frequency Identification} tag antenna which has high sensitivity for car side mirror. A proposed tag antenna ($154\;mm{\times}66\;mm{\times}1;mm$) resonants at 900 MHz and has a wide bandwidth of 690 MHz($490\;MHz{\sim}1180\;MHz$). The measured gain and readable range of tag antenna are 5.8 dBd and 10 m, respectively. Radiation pattern and readable range of proposed tag antenna located on inside of a side mirror including a car body are measured at anechoic chamber. It has been confirmed that the readable range in the vicinity of $90^{\circ}$ has been expanded about 1.5 m by comparison with one of proposed tag antenna without of car body. Good performance of the proposed tag antenna was observed and proved by comparison of measured results of commercial tag antenna.

• Journal of Mechanical Science and Technology
• /
• v.16 no.11
• /
• pp.1550-1557
• /
• 2002

Diode laser sensor for measuring gas temperature and species concentration in combustion chamber was developed using 2.0 tim distributed feed back lasers. To evaluate the measurement sensitivity of diode laser sensor system, CO2 survey spectra near 2.0 Um were measured and compared with the calculated one. This diode laser absorption sensor was applied to measure gas temperatures in a premixed flat flame of CH$_4$-air mixture. Experimental results were in good agreement with the values by an R-type thermocouple within 6.12%. In addition, successful demonstration of measurement of gas temperature and species concentration in a soot flame showed the promising possibility of diode laser absorption sensors for practical combustion system with non-intrusive method.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.04a
• /
• pp.184-189
• /
• 2000

Two types of fiber-optic sensors, EFPI(extrinsic Fabry-Perot interferometer) and FBG(fiber Bragg grating), have been investigated for measurement of thermal strain and temperature. The EFPI sensor is only for measurement of thermal strain and the FBG sensor is for simultaneous measurement of thermal strain and temperature. FBG temperature sensor was developed to measure strain-independent temperature. This sensor configuration consists of a single-fiber Bragg grating and capillary tube which makes it isolated from external strain. This sensor can then be used to compensate for the temperature cross sensitivity of a FBG strain sensor. These sensors are demonstrated by embedding them into a graphite/epoxy composite plate and by attaching them on aluminum rod and unsymmetric graphitelepoxy composite plate. All the tests were conducted in a thermal chamber with the temperature range $20-100^{\circ}C$. Results of strain measurements by fiber-optic sensors are compared with that from conventional resistive foil gauge attached on the surface.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.2
• /
• pp.127-132
• /
• 1999

Both motion of free metallic particles from which most GIS internal failures are caused and partial discharges from the particles were examined using EHV GIS test chamber. Effects from particle length and gas pressure which are main factors to lead to breakdown failure were investigated theoretically and experimentally. Magnitude of both lift-off voltage and partial discharge inception voltage were measured respectively and, through these measurements, this paper showed the possibility of predicting breakdown fault and of taking action to prevent the fault in advance. The measurement of partial discharge when the particles began to move could be adopted to decide minimum sensitivity in developing predictive diagnostic equipments. Both the amount of apparent discharge and real discharge in GIS were examined theoretically and experimentally, then experimental results were analyzed on the basis of the theory.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.10a
• /
• pp.115-119
• /
• 2011

Instead of very expensive sound record and professional measurement microphones the low cost Surface Mounted Device (SMD) microphones are proposed for practical barrier ANC system. FRF of the microphones and theirs sensitivity to the wind interferences are evaluated in semi anechoic chamber. The improvement of feedforward algorithm noise reduction index was evaluated based on measured coherence function between tested SMD and reference microphone. Test was performed at various wind speed from 1 m/s to 5 m/s.

• Journal of Biosystems Engineering
• /
• v.30 no.2 s.109
• /
• pp.114-120
• /
• 2005

In this study, a biological reaction and measurement control system was developed to rapidly measure the insecticide imidacloprid residues in agricultural products. The biological reaction part of the system was designed to include micro-pumps and valves for fluid transport, and a polystyrene covet as a reaction chamber. The measurement control part of the system consisted of a photodiode with a light-emitting diode for optical density measurement, and a control microcomputer to implement assay. Signal output was read as the rate of change in optical density at 645 nm. The sensitivity of the system was 2.2 ng/mL ($IC_50$). The system could execute a measurement cycle in about 19 minutes. Research will be continued to develop an automatic sampler fur imidacloprid residues from agricultural products.

• Korean Journal of Materials Research
• /
• v.23 no.2
• /
• pp.112-115
• /
• 2013

One of the most important characteristics of Mg alloys is the high ratio of strength to weight. This is why there is a high demand for applications with these alloys in the transportation industries to reduce the fuel consumption and to save energy. In addition, magnesium (and its alloys) is of considerable interest as a structural material, especially in the aerospace and automotive industries thanks to its low density. However, its major drawback is its high sensitivity to corrosion. Therefore, its use requires the application of a surface treatment. This study used a die-casted AZ91D Mg alloyand all the samples were annealed (in $120^{\circ}C$). The surface microstructure and phase distribution in thin-walled AZ91D magnesium components cast on a hot-chamber die-casting machine were investigated by optical microscopy and scanning electron microscopy. The reflectance differences in the bulk state comparison with the annealing state are caused by hydrogenation presence of the Mg layer under an oxidation surface layer.