• 한국세라믹학회지
• /
• 제26권2호
• /
• pp.221-227
• /
• 1989

To investigate the development and densification YBa2Cu3O7-x(1-2-3) superconducting phase, the 1-2-3 phase powders have been prepared by citrate and nitrate processes with changing calcination temperature. Nearly pure 1-2-3 phase peaks have been obtained by calcining the precursor in air at 90$0^{\circ}C$ for 2.5h in citrate process but at 95$0^{\circ}C$ for 2.5h in nitrate process. The sintering density of citrate derived sample calcined at 80$0^{\circ}C$ has been about 4% higher than that calcined at 90$0^{\circ}C$, although the compacting density has been lower at 80$0^{\circ}C$ calcination. This can be explained that the 1-2-3 phase particles formed at 80$0^{\circ}C$ have reactive sub-micron size which has good sinterbililty.

• 한국세라믹학회지
• /
• 제28권3호
• /
• pp.225-233
• /
• 1991

In this study, we tried to find out the appropriate synthetic condition and magnetic properties of Ni-Zn ferrite {(NixZn1-x)Fe2O4} powders (where X=0, 0.1, 0.2, 0.3, ……0.9, 1). Ferrite powders were prepared by wet-direct method at 86℃ for 6hrs from FeCl36H2O, NiCl26H2O, and ZnCl2. The powders of (NixZn1-x)Fe2O4 (where X=0.4, 0.5, 0.6) have a good crystallinity, but the other ferrite powders consist of crystal and precursor ferrite. The ferrite powder's lattice constant is increased when ratio of ZnO contant is increased in the ferrite composition. And initial permeability was measured after sintering, result indicated regular pattern except (Ni0.4Zn0.6)Fe2O4 when the frequency were changed 10KHz to 10MHz.

• 한국세라믹학회지
• /
• 제53권6호
• /
• pp.647-651
• /
• 2016

SiC films were prepared on glassy carbon substrates by laser chemical vapor deposition under a high pressure of $10^4Pa$ using a diode laser (wavelength = 808 nm) and a polysilaethylene precursor. (111)-oriented SiC films were formed at a deposition temperature ($T_{dep}$) range of 1150 - 1422 K. At $T_{dep}=1262K$, the SiC film with a high Lotgering factor of above 0.96 showed an exhibited pyramid-like surface morphology and flower-like grains. The highest deposition rate ($R_{dep}$) was $220{\mu}m\;h^{-1}$ at $T_{dep}=1262K$.

• 한국세라믹학회지
• /
• 제31권4호
• /
• pp.381-388
• /
• 1994

A new process which co-fires the low-firing-substrate and copper conductor was studied to achieve good bond strength and low sheet resistance of conductor. Cupric oxide is used as the precursor of conductive material in the new method and the firing atmosphere of the new process is changed sequently in air H2N2. The addition of cupric oxide and variations of firing atmosphere permited complete binder-burnout in comparison with the conventional method and contributed to the improvement of resistance and bonding behaviors. The potimum conditions of this experiment to obtain the satisfactory resistance and bond strength are as follows (binder-burnout temperature in air; 55$0^{\circ}C$, reducing temperature in H2; 40$0^{\circ}C$ for 30 min, ratio of copper and cupric oxide; 60:40~30:70 wt%). The bonding mechanism between the substrate and metal was explained by metal diffusion layer in the interface and the bond strength mainly depended on the stress caused by the difference of shrinkage and thermal expansion coefficient between the substrate and metal.

• 한국세라믹학회지
• /
• 제43권11호
• /
• pp.710-714
• /
• 2006

Barium titanate nanoparticles were synthesized under N$_2$ atmosphere by the hydrolysis and condensation of barium hydroxide octahydrate and titanium (IV) isopropoxide. The synthesized particles were aggregates of nanosized primary particles. The primary particles of about 20-50 nm in diameter became building blocks of larger secondary particles, which are in most cases spherical in shape. The size and morphological evolution of secondary particles are strongly related to the precursor concentration. The observations suggest that formation and control of secondary particles is an essential step in the alkoxidehydroxide sol-precipitation process to obtain monodispersed barium titanate nanopowders.

• 한국세라믹학회지
• /
• 제53권5호
• /
• pp.541-547
• /
• 2016

In developing high temperature molds with advantages of the sand and precision (investment) castings, mechanical properties of the mold were improved through homogeneous coating of starting powders with an inorganic binder and improvement of fabrication process. Beads with mullite composition were employed for properties of the mold under high temperature, which was compared with artificial sands. Precursors of silica and sodium oxide were used as starting materials for an inorganic binder to achieve homogeneous coating on the starting powders. Strength was enhanced by the glass phase converted from the inorganic binder through heat treatment process. Also, two kinds of process, wet and dry processes, were incorporated to prepare mold specimens. Consequently, fabrication process of the mold with superior strength and high temperature applicability, compared with the previous molds for sand casting, could be suggested through control of the starting material and enhancement of the vitrification efficiency.

• Journal of Ceramic Processing Research
• /
• 제13권spc1호
• /
• pp.110-113
• /
• 2012

Ge-S and Li-Ge-S powders were synthesized via solution-based process in order to employ chalcogenide-based solid electrolyte for use in Li secondary batteries. GeCl4 and thioacetamide in combination result in Ge-S powders of which major crystalline phase becomes GeS2 where the tetragonal and orthorhombic phases coexist after heat treatment. A chemical treatment using NaOH brings about the reduction of chlorine in the powders obtained. However, the heat treatment at 300 ℃ is more effective in minimizing the chlorine content. When lithium chloride is used as the precursor of Li ions, the LiCl powders are agglomerated with an inhomogeneous distribution. When Li2S is used, the Li-Ge-S powders are distributed more uniformly and the orthorhombic GeS2 phase dominates in the powders.

• 한국세라믹학회지
• /
• 제39권11호
• /
• pp.1113-1118
• /
• 2002

마이크로파 유전체용 $(Pb_{0.5}Ca_{0.5})(Fe_{0.5}Nb_{0.5})O_3$ (PCFN) 나노 분말을 metal-citrate 공정을 이용하여 합성하였다. 금속 이온들과 유기 조직의 결합으로 이루어진 고분자 전구체를 형성시키고 이를 열처리하여 화학양론적 조성과 균일한 크기 분포를 갖는 PCFN 분말을 성공적으로 합성하였다. 초기 비정질상 PCFN 분말은 약 $400{\circ}$에서부터 결정화가 시작되어 $700{\circ}$에서 완전한 결정화를 이루었고, $900{\circ}$ 이상에서는 PbO의 해리로 인한 pyrochlore상이 생성되었다. $700{\circ}$에서 열처리된 단일상의 perovskite PCFN 분말은 약 40 nm의 평균 크기와 균일한 형상으로 분포되어 있었다.

• 폴리머
• /
• 제24권3호
• /
• pp.299-305
• /
• 2000

고온에서 열적 안정성이 우수한 hybrid 세라믹 전구체를 합성하기 위하여 polycarbosilane (PCS)의 화학적 개질에 의해 Si-O-Ti-C 구조를 갖는 세라믹 전구체를 합성하였다. 합성한 공중합체의 FT-IR 스펙트럼 결과 2893, 1092t 609$cm^{-1}$ / 부근에서 피크변화를 나타났으며, $^1$H-NMR 스펙트럼의 $\delta$=3.8, 2.0, 0.6 ppm 부근에서 특성피크가 나타나는 것을 확인함으로써 전구체 합성을 확인하였다. 초기 열분해 온도와 열분해 전환율 변화를 알아보기 위한 열중량 분석 (TGA) 결과 열분해 초기 온도가 30$0^{\circ}C$로 낮아졌으며 열분해 전환율도 74 wt%로 순수한 PCS에 비해 10 wt%가 증가함을 보였다. 또한 150$0^{\circ}C$까지 열분해시킨 후 X-선 회절분석 결과 2$\theta$=35.7, 42.2, 61.0$^{\circ}$에서 결정성 피크로 $\beta$-SiC의 전환을 확인하였다.

• Journal of Electrochemical Science and Technology
• /
• 제8권4호
• /
• pp.338-343
• /
• 2017

Activated carbon has lower electrical conductivity and reliability than other carbonaceous materials because of the oxygen functional groups that form during the activation process. This problem can be overcome by doping the material with heteroatoms to reduce the number of oxygen functional groups. In the present study, N, F co-doped activated carbon (AC-NF) was successfully prepared by a microwave-assisted hydrothermal method, utilizing commercial activated carbon (AC-R) as the precursor and ammonium tetrafluoroborate as the single source for the co-doping of N and F. AC-NF showed improved electrical conductivity ($3.8\;S\;cm^{-1}$) with N and F contents of 0.6 and 0.1 at%, respectively. The introduction of N and F improved the performance of the pertinent supercapacitor: AC-NF exhibited an improved rate capability at current densities of $0.5-50mA\;cm^{-2}$. The rate capability was higher compared to that of raw activated carbon because N and F codoping increased the electrical conductivity of AC-NF. The developed method for the co-doping of N and F using a single source is cost-effective and yields AC-NF with excellent electrochemical properties; thus, it has promising applications in the commercialization of energy storage devices.