• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.185-188
• /
• 1998

A three-waveguide coupler consisted of a central guide and two side guides is theoretically explored by using modal transmission-line theory. The numerical results reveal that the coupling length Lc is different from that calculated by coupled-mode theory and the difference increases gradually as the guiding modes increase.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.2
• /
• pp.262-270
• /
• 2013

A boundary protection method for power distribution line based on equivalent boundary effect is presented in this paper. In the proposed scheme, the equivalent resonance component with a certain central frequency is sleeve-mounted at the beginning of protected zone. The 'Line Boundary' is built by using boundary effect, which is created by introducing impedance in the primary-side of line. The 'Line Boundary' is significantly different from line wave impedance. Therefore, the boundary protection principle can be applied to power distribution line without line traps. To analyze the frequency characteristic corresponding to traveling-waves of introducing impedance in the primary-side of line, distributed parameters model of equivalent resonance component is established. The results of PSCAD/EMTDC simulation prove the obvious difference of voltage high frequency component between internal faults and external faults due to equivalent resonance component, and validate the scheme.

• The korean journal of orthodontics
• /
• v.5 no.1
• /
• pp.57-63
• /
• 1975

For the purposes of augmentation of the aid for case analysis and diagnosis of malocclusion, a roentgenocephalometric study was made from 84 Korean adolescences. The Subjects consist of 42 males and 42 females aged from 17 to 20 years with normal occlusion and acceptable facial appearance. The author measured 18 angles and 14 linear distances as suggested by Jarabak. The following results were obtained. 1) Each linear measurement of the males' skull was greaten than that of the females. 2) The posterior to anterior facial height was $69.2\%$ in the males and $67.1\%$ in the females. 3) In the relationship of upper lip to esthetic line, the lip of females was more behind than that of males. 4) Saddle angle was $124.7^{\circ}$, articular angle was $148.7^{\circ}$, genial angle was $119.4^{\circ}$ and upper and lower genial angles were $45.1^{\circ}\;(N-Go-a^{\circ})$ and $74.2^{\circ}\;(N-Go-Me^{\circ})$. 5) The ratio of mandibular body to anterior cranial base was about 1:1. 1. 6) The angulations of $SNA^{\circ},\;SNB^{\circ}\;and\;SNP^{\circ}$ were as follows; $SNA^{\circ},\;80.3^{\circ},\;SNB^{\circ},\;79.8^{\circ},\;SNP^{\circ},\;81.1^{\circ}$. 7) The angle of the sella-nasion plane to the mandibular plane $(SNG^{\circ}Me^{\circ})$ was $32.0^{\circ}$ and that of the occlusal plane to the mandibular plane was $18.2^{\circ}$. 8) The angle of the maxillary central incisor to the sellanasion plane $(1-SN^{\circ})$ was $105.6^{\circ}$. That of the mandibular central incisor to the mandibular plane $(1-GoMe^{\circ})$ was $94.0^{\circ}$, and the interincisal angle $(1\;to\;1^{\circ})$ was $127.6^{\circ}$. 9) The linear distance from incisal edge of upper central incisor to facial plane was 8.0mm and that of lower central incisor was 4.6mm. 10) In the relationship of the lower lip to the esthetic line, the lower lip was 0.2mm front of the esthetic line.

• Neonatal Medicine
• /
• v.28 no.3
• /
• pp.116-123
• /
• 2021

Purpose: The aim of this study was to estimate the effect of targeting risk factors for the control of central line-associated bloodstream infection (CLABSI) among high-risk infants in a tertiary neonatal intensive care unit (NICU). Methods: Infants admitted to the NICU and diagnosed with CLABSI from January to December 2013 were eligible for inclusion to the study. The CLABSI group (n=47) was matched in a 1:2 ratio to the control group (n=94) based on gestational age, birth weight, and Score for Neonatal Acute Physiology-II. Risk factors for CLABSI were identified using the Cox proportional hazard model, and analysis of the effect of these risk factors targeting infection control was performed. Results: The risk factors associated with CLABSI were prolonged central line dwell days (adjusted hazard ratio [HR], 1.028; 95% confidence interval [CI], 1.011 to 1.045; P=0.001), use of a silicone catheter (adjusted HR, 5.895; 95% CI, 1.893 to 18.355; P=0.002), surgical treatment (adjusted HR, 3.793; 95% CI, 1.467 to 9.805; P=0.006), and less probiotic supplementation (adjusted HR, 0.254; 95% CI, 0.068 to 0.949; P=0.042). By targeting these risk factors with a quality improvement initiative, the mean CLABSI incidence rate per 1,000 catheter-days decreased from 6.6 to 3.1 (P=0.004). Conclusion: Targeting risk factors for infection control significantly reduced the rate of CLABSI among high-risk infants in the NICU.

• The Journal of Korea Robotics Society
• /
• v.9 no.3
• /
• pp.147-153
• /
• 2014

In this paper, we proposed a new algorithm of the guidance line extraction for autonomous weeding robot based on infrared vision sensor in wet paddy. It is the critical process for guidance line extraction which finds the central point or area of rice row. In order to improve accuracy of the guidance line, we are trying to use the morphological characteristics of rice that the direction of rice leaves have convergence to central area of rice row. Using Hough transform, we were represented the curved leaves as a combination of segmented straight lines on binary image that has been skeletonized and segmented object. A slope of the guidance line was gotten as calculate the average slope of all segmented lines. An initial point of the guidance line was determined that is the maximum pixel value of the accumulated white columns of a binary image which is rotated the slope of guidance line in the opposite direction. We also have verified an accuracy of the proposed algorithm by experiments in the real wet paddy.

• Journal of the Korean Society of Tobacco Science
• /
• v.28 no.2
• /
• pp.100-110
• /
• 2006

A mutant of Potato vims Y (PVY) was occurred in PVY resistance flue-cured tobacco breeding line KF0402 $(TC1146{\times}KF117)$ showing vein necrosis at Suwon in Korea. This isolate, PVY-SWM, was differentiated from other PVY based on biological properties and nucleotide sequence analyses of coat protein gene. PVY-SWM caused typical symptoms on 21 indicator plants as compared to the PVY-TOJC37. Remarkably, the PVY-SWM induced distinctly different symptom of systemic vein necrosis on tobacco cultivars V.SCR, PBD6, TN86, TN90, Virgin A Mutant (VAM), Wislica, NC744, KB108 and KB111, which were reported to have the recessive potyvirus resistance gene va. In RT-PCR assays with specific primers for detection of PVY, a single band of about 800bp in length was produced. The amplified DNA was cloned and the nucleotide sequence was determined. The coat protein gene of PVY-SWM showed 88.4%-99.0% and 92.5%-98.5% identities to the 12 different PVY isolates of Genbank Database at the nucleotide and amino acidi respectively. Multiple alignments as well as cluster dendrograms of PVY-SWM isolate revealed close phylogenetic relationship to the $PVY^{NTN}$ subgroup.

• Journal of The Korean Astronomical Society
• /
• v.36 no.spc1
• /
• pp.55-61
• /
• 2003

There are at least three effects of the non-thermal particle bombardment on the solar atmosphere: (1) non-thermal ionization and excitation; (2) proton-hydrogen charge exchange; (3) impact line polarization. Due to the non-thermal ionization and excitation effects of electron bombardments in flares, H$\alpha$ line is widely broadened and shows a strong central reversal. Significant enhancements at the line wings of Ly$\alpha$ and Ly$\beta$ are also predicted. In the case of proton bombardment, less strong broadening and no large central reversal are expected. However, due to proton-hydrogen charge exchange, the enhancements at the red wings of Ly$\alpha$ and especially of Ly$\beta$ lines at the early impulsive phase of flares are significant. Electron beam can also in some cases generates visible and UV continuum emission in white-light flares. However, at the onset phase, a negative 'black' flare may appear in several seconds, due to the increase of the $H^-$ opacity. The impact polarization of atomic lines can provide complementary information on the energetic particles, the energy transport and deposit in the solar chromosphere. New results of spectropolarimetric analysis for the major flare on July 23, 2002 are also given in the paper.

• Journal of the Korean Society of Costume
• /
• v.52 no.6
• /
• pp.1-13
• /
• 2002

This paper investigated the costumes of young girl dancers in Yon wha dae moo(연화대무: Lotus Stage dance) which were documented on the Ak-hak-guae-bum(악학궤범: Protocol of music) and the Jin-yeon-eui-guae(진연의궤: Archives of Royal Feast). The fashion of the costumes can be changed into three phases, based mainly on the changes of Hap-rip(합립: silk hat), Dan-eui(단의: long jacket) and Sang(상: apron type skirt). In the first phase the costume consisted of Hap-rip, round neck-line Dan-eui and tiered skirt decorated with pleat and Yu-so(유소: decorated cords). In the second phase. it consisted of Hap-rip, v-shape neck-line Dan-eui and skirt without pleat. In the third phase, it consisted of Yeon-wha-gwan(연화관: Lotus shape cap), round neck-line Dan-eui of later era and skirt with pleat and Yu-so. Yon-wha-dae dance appears to be adopted from Ja-ji-mu( 자지무: chinese dance) that originated in West and Central Asia. In both dances. young girl dancers danced mainly jump and spin. The costume of round neck-line Dan-eui seems to have been affected by the fashion in Dang Dynasty when young girls loved to wear Dan-ryung(단령: male coat with round neckline). And it satisfied the need of mobility for the dance which was Performed mainly with jump.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.9
• /
• pp.179-185
• /
• 2001

In this study, a visual sensor system for weld seam tracking the I-butt weld joints in GMA welding was constructed. The sensor system consists of a CCD camera, a diode laser with a cylindrical lens and a band-pass-filter to overcome the degrading of image due to spatters and arc light. In order to obtain the enhanced image, quantitative relationship between laser intensity and iris number was investigated. Throughout the repeated experiments, the shutter speed was set at 1-milisecond for minimizing the effect of spatters on the image, and therefore most of the spatter trace in the image have been found to be reduced. Region of interest was defined from the entire image and gray level of searched laser line was compared to that of weld line. The differences between these gray levels lead to spot the position of weld joint using central difference method. The results showed that, as long as weld line was within $^\pm$15$^\circ$from the longitudinal straight fine, the system constructed in this study could track the weld line successful1y. Since the processing time reduced to 0.05 sec, it is expected that the developed method could be adopted to high speed welding such as laser welding.

• Journal of Mechanical Science and Technology
• /
• v.19 no.10
• /
• pp.1856-1863
• /
• 2005

In this study, a visual sensor system for weld seam tracking the I-butt weld joints in GMA welding was constructed. The sensor system consists of a CCD camera, a diode laser with a cylindrical lens and a band-pass-filter to overcome the degrading of image due to spatters and arc light. In order to obtain the enhanced image, quantitative relationship between laser intensity and iris opening was investigated. Throughout the repeated experiments, the shutter speed was set at 1/1000 second for minimizing the effect of spatters on the image, and therefore the image without the spatter traces could be obtained. Region of interest was defined from the entire image and gray level of the searched laser stripe was compared to that of weld line. The differences between these gray levels lead to spot the position of weld joint using central difference method. The results showed that, as long as weld line is within $\pm15^{o}$ from the longitudinal straight line, the system constructed in this study could track the weld line successfully. Since the processing time is no longer than 0.05 sec, it is expected that the developed method could be adopted to high speed welding such as laser welding.