• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.2
• /
• pp.157-164
• /
• 2016

In this research, based on the condition of using desulfurization gypsum(FGD) as a stimulator for high-volume blast furnace slag cement mortar, sieving and heating process methods of removing activated carbon in FGD were compared with the non-processed FGD and recycled and natural fine aggregates were compared for suitable aggregate to be used. According to the result of experiment, sieving with 0.3mm was more efficient than $500^{\circ}C$ heating for processing the FGD, and recycled fine aggregate showed more favorable result than natural fine aggregate at the FGD content was 5 to 10%. On the other hand, the mortar mixture including recycled fine aggregate had a high drying shrinkage, and absorption ratio, and thus specific limitations on applying recycled fine aggregate should be required.

• Journal of the Mineralogical Society of Korea
• /
• v.22 no.4
• /
• pp.353-358
• /
• 2009

The ability of natural abrasives which were recovered from CRT glass polishing process was evaluated. Comparing the center line average roughness values of a glass polished with new pumice (Ra = $0.039{\mu}m$) and with new garnet (Ra = $0.031{\mu}m$), the glass surface polished with the recycled pumice and the garnet had less pits on the surface with smaller Ra values (Ra = $0.025{\mu}m$ for recycled pumice and Ra = 0.029 for recycled garnet). Recycled rouge contains amorphous glass fragments so that it should be used as a cement replacement rather than recycle into an abrasive. Nnatural abrasives, pumice and garnet powder, which are used in CRT glass polishing process can be recycled into abrasives so that it can help to minimize costs and environmental impact from the production of abrasives and the disposal of waste sludge.

• Computers and Concrete
• /
• v.17 no.6
• /
• pp.787-799
• /
• 2016

Climate anomalies in recent years, numerous natural disasters caused by landslides and a large amount of entrained sands and stones in Taiwan have created significant disasters and greater difficulties in subsequent reconstruction. How to respond to these problems efficaciously is an important issue. In this study, the sands and stones were doped with recycled materials (waste LCD glass sand, slag powder), and material was mixed for recycled ready-mixed soil. The study is based on security and economic principles, using flowability test to determine the water-binder ratio (W/B=2.4, 2.6, and 2.8), a fixed soil: sand ratio of 6:4 and a soil: sand: glass ratio of 6:2:2 as fine aggregate. Slag (at concentrations of 0%, 20%, and 40%) replaced the cement. The following tests were conducted: flowability, initial setting time, unit weight, drop-weight and compressive strength. The results show that the slump values are 220 -290 mm, the slump flow values are 460 -1030 mm, and the tube flow values are 240-590 mm, all conforming to the objectives of the design. The initial setting times are 945-1695 min. The unit weight deviations are 0.1-0.6%. The three groups of mixtures conform to the specification, being below 7.6 cm in the drop-weight test. In the compressive strength test, the water-binder ratios for 2.4 are optimal ($13.78-17.84kgf/cm^2$). The results show that Recycled ready-mixed soil materials (RRMSM) possesses excellent flowability. The other properties, applied to backfill engineering, can effectively save costs and are conducive to environmental protection.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.5
• /
• pp.165-172
• /
• 2021

The purpose of this study is to investigate the carbon capture capacity of various inorganic materials. For this purpose, the change in property of ordinary Portland cement (OPC), blast furnace slag fine powder (GGBS), and circulating fluidized bed boiler ash (CFBC) due to carbonation were analyzed. Carbonation curing was performed on all specimens through the accelerated carbonation experiment, and the amount of carbon capture was quantitatively analyzed by thermogravimetric analysis according to the age of carbonation. From the results, it is confirmed that the carbon capture capacity was shown in all specimens. The carbon capture amount was shown in the order of CFBC, OPC, and GGBS. The 28-day carbon capture of CFBC, OPC, and GGBS was 3.9%, 1.3%, and 9.4%, respectively. Carbon capture reaction occurred rapidly at the beginning of carbonation, and occurred slowly with increasing age. SEM image analysis revealed that an additional product generated by carbonation curing in all specimens was calcium carbonate.

• Journal of the Korea Institute of Building Construction
• /
• v.18 no.6
• /
• pp.527-532
• /
• 2018

The objective of the present study is to evaluate a practical approach for enhancing the compressive strength and minimizing deforming of aerated concrete. Test results measured in the aerated concrete mixes that were produced using 40% ground granulated blast-furnace slag (GGBS) as a replacement of cement and cured under different conditions (i.e., high temperatures of $40^{\circ}C$ and $60^{\circ}C$ for 10 hrs or 15 hrs) were compared with those obtained from the specimens cured under room temperature. No deforming was observed in the mixes with 40% GGBS. The compressive strength of the prepared aerated concrete cured under high temperature was higher than that of the concrete cured at room temperature, even at the lower ranges of the apparent dry density. However, the curing time is needed to be controlled as not exceeding 10 hrs at the temperature of $60^{\circ}C$ to prevent the decrease in the compressive strength due to foam mergences.

• Resources Recycling
• /
• v.27 no.6
• /
• pp.30-37
• /
• 2018

A series of experiment was conducted to evaluate basic performances of low-pH, anti-washing grouts incorporating gypsum which applied for reinforcing underwater cavities in limestone- grounds. Various types of mix proportions were designed and the fluidity, strength and environmental impact of these mixtures were evaluated. The flowability was evaluated under two conditions, i.e., flows without and with pressing, respectively. Strength was measured for the hardened mixtures fabricated under conditions of air and water injections. The environmental impacts including the pH of the suspension and the suspended solids concentration for the mixtures were evaluated. The low pH of fresh mixture suspension, below than 10, was achieved by incorporation of gypsum. The mix proportions of cement-quartz powder-gypsum binders and chemical agents resulted in mortar natural flow 7-10 cm and uniaxial compressive strength 4 MPa were derived.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.3
• /
• pp.287-294
• /
• 2021

In this study, tests were performed to analyze the feasibility of using the ground stabilizer from recycled resources such as blast furnace slag powder as filling material of prebored piles. For this, specimens were prepared by applying 70% and 83% of the general water/binder ratio of the filling material of prebored piles. And compression test, model test, and shaking table test were performed to determine the compressive strength, skin friction on the surface between prebored pile and filling material, and seismic performance of ground stabilizer. As a result of the tests, the compressive strength exceeded the relevant domestic standards, and the skin friction was equivalent to that of ordinary portland cement. In addition, the amount of vertical and horizontal displacement caused by earthquakes was found to be much smaller than the domestic standard. Therefore, when considering the test results comprehensively, it is judged that the feasibility of using a ground stabilizer from recycled resources as filling material for prebored pile is sufficient.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.35 no.12
• /
• pp.165-172
• /
• 2019

The aim of the research is to evaluate the influence of various replacing ratios of supplementary cementitious materials(SCMs) such as fly ash(FA), blast furnace slag(BS), and both FA and BS on general properties including segregation resistance as a powder based high fluidity concrete of normal strength grade with water-to-cement ratio 0.40. Specifically, by replacing the SCMs with low density powders, it was assessed that the decreased segregation resistance due to the decreased viscosity by J-ring test. As a result of the experiment, from the general test, the mixtures with SCMs showed increased segregation resistance by increased viscosity as the references, while some segregation was shown from J-ring test due to the decreased density of fresh state mixture related with the capacity of delivering coarse aggregate.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.1
• /
• pp.66-73
• /
• 2022

The purpose of this study was to develop self-heating concrete by utilizing the conduction resistance of concrete in order to reduce the risk of occurrence of black ice in the concrete pavement in winter and to prevent damage caused by freez-thawing effect. For this purpose, it was attempted to evaluate the strength and temperature exothermic characteristics using powder and liquid waste CNTs and a waste cathode agent as a conduction promotion. It was analyzed that liquid waste CNT had an effective dispersion degree in the mortar and a small decrease in strength occurred. In addition, DC 24 V was supplied by applying steel mesh, copper foil and copper wire to the mortar as electrodes, and the temperature change characteristics according to the mixing ratio of spent CNTs, anodes and carbon fibers were evaluated. In addition, by evaluating the temperature characteristics according to the electrode spacing from the selected optimal mixture, it was confirmed that it had sufficient heating characteristics up to an electrode spacing of 100 mm up to AC 50 V.

• The Journal of Engineering Geology
• /
• v.32 no.4
• /
• pp.661-670
• /
• 2022

In recent years, extreme rainfall and rainy seasons caused by climate change have caused river flooding and flooding damage, and it is urgent to solve economic and environmental problems in the city center due to the increase in the number of peak homes. The gap block, called the fitting block, is designed to facilitate rainwater pitching by forming a gap between the block and the block by forming a concave part and a protrusion of the block differently without the use of an existing spacer. In this study, for the production of such a gap block, the existing cement content was reduced and aramid fibers and exploration fibers, which are industrial by-products such as Goroslag fine powder and reinforcing fibers, were applied.