• 전기전자학회논문지
• /
• 제21권3호
• /
• pp.272-275
• /
• 2017

최근 반도체의 집적도가 증가하고 배선 폭이 미세해짐에 따라 칩 수준의 EMI(electromagnetic interference)가 문제로 대두되고 있다. 이에 따라 칩 제조사는 칩 수준의 EMI를 측정하기 위해 TEM 셀(transverse electromagnetic cell)을 사용하고 있다. 이를 위해 측정용 PCB(printed circuit board)를 제작하여야 하지만, PCB의 배선 패턴 등이 EMI 측정에 영향을 미칠 수 있다는 점이 간과되고 있다. 본 논문에서는 PCB 설계 변수를 변화시켜가며 테스트 패턴을 제작한 다음 TEM 셀의 EMI 측정에 미치는 영향을 분석하였다. 또한 이를 바탕으로 EMI 측정에 미치는 영향을 최소화하기 위한 PCB 설계 가이드라인을 제시하였다.

• 한국수소및신에너지학회논문집
• /
• 제23권5호
• /
• pp.484-492
• /
• 2012

The TMS(Thermal Management System) heater in a fuel cell vehicle has been developed to prevent a decline of fuel cell durability and cold start durability. Main functions of the COD(Cathode Oxygen Depletion) heater are depletion of oxygen in a cathode as heat energy and consumption of electric power for rapid warming up of a fuel cell stack. This paper covers subjects including the design specification of a heater, heater controller for detection of overheat and reliability assessment including coolant pressure cycle test of a heater. To verify the design concept, burst pressure and deformation analysis of plastic housing were carried out. Also, temperature distribution analysis of heater surface and coolant inside of housing were carried out to verify the design concept. By designing the plastic housing instead of a steel housing, the 30% weight lightening and 50% cost reduction were attained. A module-based design of a TMS system including a heater or reducing the watt density of a heater is a problem to be solved in the near future work.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.13-16
• /
• 2008

Solid oxide fuel cell(SOFC) is an electrochemical energy conversion system with high efficiency and low-emission of pollution. In order to reduce the operating temperature of SOFC system under $800^{\circ}C$, the thickness reduction of YSZ electrolyte to be as thin as possible, e.g., less than 10 ${\mu}m$ are considered with the microstructure control and optimum design of unit cell. Methods for reducing the thickness of YSZ electrolyte have been investigated in coin cell. Moreover, a large unit cell($8cm{\times}8cm$) for SOFC was fabricated using an anode-supported electrolyte assembly with a thinner electrolyte layer, which was prepared by a tape casting method with a co-sintering technique. we studied the design factors such as active layer, electrolyte thickness, cathode composition, etc,. by the coin type of unit cell ahead of the fabrication process of a large unit cell and also reviewed about the evaluation technique of a large size unit cell such as interconnect design, sealing materials and current collector and so forth. Electrochemical evaluations of the unit cells, including measurements such as power density and impedance, were performed and analyzed. Maximum power density and polarization impedance of coin cell were 0.34W/$cm^2$ and $0.45{\Omega}cm^2$ at $800^{\circ}C$, respectively. However, Maxium power density of a large unit cell($5cm{\times}5cm$) decreased to 0.21W/$cm^2$ at $800^{\circ}C$ due to the increase of ohmic resistance. However, It was found that the potential value of a large unit cell loaded by 0.22A/$cm^2$ showed 0.76V at 100hrs without the degradation of unit cell.

• 한국통신학회논문지
• /
• 제15권8호
• /
• pp.639-647
• /
• 1990

음성 인식에서의 dynamic time warp(DTW)은 반복적 계산을 필요로 하며, 이 계산을 수행하기에 합당한 PE cell의 설계는 매우 중요하다. 따라서 이 연구에서는 실제에 가까운 실시간 어휘 인식을 가능하게 하는 large dictionary 의 DTW 알고리즘을 hardware로 구현하기 위한 PE(Processing Element) cell의 설계에 주안점을 두었다. 이 DTW 용 PE cell은 크게 세가지의 블록으로 대별된다. 즉 MIN block, ADD block 그리고 ABS block인데, "MIN"은 accumulated minimum distance를 계산하기 위한 블록이고 "ADD"는 이들 minimum distance들의 합을 계산하는 블록, 그리고"ABS"는 이러한 합에 의한 local distance의 절대값을 구하기 위한 블록이다. 본 연구에서는 이들 세가지 블록중 MIN 회로의 설계 및 검증을 행하였으며, 3um CMOS N-well 설계 규칙에 따라 MIN 블록에 대한 레이아웃을 행한 후 설계 규칙 검사(DRC)를 마쳤다.레이아웃을 행한 후 설계 규칙 검사(DRC)를 마쳤다.

• 방사성폐기물학회지
• /
• 제21권4호
• /
• pp.517-529
• /
• 2023

The objectives of this paper are: (1) to conduct the thermal analyses of the disposal cell using COMSOL Multiphysics; (2) to determine whether the design of the disposal cell satisfies the thermal design requirement; and (3) to evaluate the effect of design modifications on the temperature of the disposal cell. Specifically, the analysis incorporated a heterogeneous model of 236 fuel rod heat sources of spent nuclear fuel (SNF) to improve the reality of the modeling. In the reference case, the design, featuring 8 m between deposition holes and 30 m between deposition tunnels for 40 years of the SNF cooling time, did not meet the design requirement. For the first modified case, the designs with 9 m and 10 m between the deposition holes for the cooling time of 40 years and five spacings for 50 and 60 years were found to meet the requirement. For the second modified case, the designs with 35 m and 40 m between the deposition tunnels for 40 years, 25 m to 40 m for 50 years and five spacings for 60 years also met the requirement. This study contributes to the advancement of the thermal analysis technique of a disposal cell.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 하계종합학술대회 논문집(2)
• /
• pp.419-422
• /
• 2004

A sensing scheme for current-mode magneto-resistance random access memory (MRAM) with a 1T1MTJ cell structure is proposed. Magnetic tunnel junction (MTJ) resistance, which is HIGH or LOW, is converted to different cell currents during READ operation. The cell current is then amplified to be evaluated by the reference cell current. In this scheme, conventional bit line sense amplifiers are not required and the operation is less sensitive to voltage noise than that of voltage-mode circuit is. It has been confirmed with HSPICE simulations using a 0.35-${\mu}m$ 2-poly 4-metal CMOS technology.

• Nuclear Engineering and Technology
• /
• 제49권8호
• /
• pp.1717-1726
• /
• 2017

In the nuclear industry, mechanical engineers spend a significant portion of their time designing equipment such as manipulators, bogies, mechanical grippers, and so on. Some customized designs can be considered as standard mechanical equipment in this area, although it is not unusual to find that an existing design cannot simply be copied from one project to another. Varied performance requirements can dictate that redesign, often quite extensive redesign, is required. However, if something similar has been done before, engineers could use that as a starting point for the new project. In this regard, this study presents several guidelines inspired by previous design knowledge for similar development cases. Moreover, this study presents more detailed suggestions such as design guidelines for an argon-based hot cell atmosphere and design experience for a large-scale practical hot cell facility. Design considerations and case studies dealt with in this study are dedicated to teleoperation manipulators that are used at a large-scale argon cell facility for pyroprocess integrated inactive demonstration (PRIDE), at the Korea Atomic Energy Research Institute. In particular, for case studies to support the suggested recommendations, a fabricated telemanipulator system for PRIDE is introduced, and several kinds of experimental results associated with it are presented.

• 대한산업공학회지
• /
• 제23권3호
• /
• pp.581-595
• /
• 1997

The procedure of grouping the machines and parts to form cells is called manufacturing cell design. The manufacturing cell design is an important step in the development and implementation of advanced manufacturing systems. For the successful implementation of the manufacturing systems, identification of independent manufacturing cells, i.e., cells where parts are completely processed in the cell and no intercell movements, is necessary in the design phase. In this paper, we developed a mixed integer programming model and genetic algorithm based procedure to solve the independent manufacturing cells design problem considering the alternative process plans and machines duplication. Several manufacturing parameters such as, production volume, machine capacity, processing time, number of cells and cell size, are considered in the process. The model determines the process plan for parts, port families and machine cells simultaneously. The model has been verified with the numerical examples.

• 한국공작기계학회논문집
• /
• 제12권6호
• /
• pp.92-96
• /
• 2003

Feul-Cell system consists of fuel reformer, stack and energy translator. Among these parts, stack is a core part which produces electricity directly. In order to set a stack module, fabrication of appropriate stack, design of water flow path in stack and control of coolant are needed. Especially, oater or air is used as a coolant to dissipate heat. The different temperature of each electric cell after cooling affects the performance of the stack. Therefore, it is necessary that the relationship between coolant hearing rate, width of stack, properties of stack, and the shape of water flow path must be understood. For the optimal design, the computational simulation by CFD-ACE has been conducted and the resulting database has been constructed.

• 한국CDE학회논문집
• /
• 제12권4호
• /
• pp.245-254
• /
• 2007

This research proposed feature extraction algorithms as an input of STEP Ap214 data, and feature parameterization process to simplify further design change and maintenance. The procedure starts with suppression of blend faces of an input solid model to generate its simplified model, where both constant and variable-radius blends are considered. Most existing cell decomposition algorithms utilize concave edges, and they usually require complex procedures and computing time in recomposing the cells. The proposed algorithm using reference features, however, was found to be more efficient through testing with a few sample cases. In addition, the algorithm is able to recognize depression features, which is another strong point compared to the existing cell decomposition approaches. The proposed algorithm was implemented on a commercial CAD system and tested with selected industrial product models, along with parameterization of recognized features for further design change.