• Geomechanics and Engineering
• /
• 제28권4호
• /
• pp.405-419
• /
• 2022

Cavity expansion and contraction solutions for cylindrical and spherical cavities in unsaturated residual soils are presented in this paper. Varying soil state in the plastic zone is accounted by a numerical approach, wherein an element-by-element discretization of the plastic zone of both expanding and contracting cavities is carried out. Unlike existing methods utilizing self-similarity technique, the solution procedure enables the prediction of entire soil-state at any stage of expansion and subsequent contraction. It is also applicable for both cavity creation and expansion problems. The approach adopts constant contribution of suction to effective stress (constant X^s drainage condition) for analysis. The analysis procedure is validated by interpreting the previously reported pressuremeter test results in lateritic residual soil. The typical cavity expansion and contraction characteristics of unsaturated Indian lateritic soil were then examined using this solution procedure. The effect of initial soil-state on cavity limit pressure, plastic radius, reverse yield pressure, and reverse plastic radius are also presented.

• Geomechanics and Engineering
• /
• 제13권6호
• /
• pp.907-928
• /
• 2017

The effects of seepage force and out-of-plane stress on cavity contracting and tunnel opening was investigated in this study. The generalized Hoek-Brown (H-B) failure criterion and non-associated flow rule were adopted. Because of the complex solution of pore pressure in an arbitrary direction, only the pore pressure through the radial direction was assumed in this paper. In order to investigate the effect of out-of-plane stress and seepage force on the cavity contraction and circular tunnel opening, three cases of the out-of-plane stress being the minor, intermediate, or major principal stress are assumed separately. A method of plane strain problem is adopted to obtain the stress and strain for cavity contracting and circular tunnel opening for three cases, respectively, that incorporated the effects of seepage force. The proposed solutions were validated by the published results and the correction is verified. Several cases were analyzed, and parameter studies were conducted to highlight the effects of seepage force, H-B constants, and out-of-plane stress on stress, displacement, and plastic radius with the numerical method. The proposed method may be used to address the complex problems of cavity contraction and tunnel opening in rock mass.

• Restorative Dentistry and Endodontics
• /
• 제25권1호
• /
• pp.91-108
• /
• 2000

Most of cervical abrasion and erosion lesions show gingival margin where the cavosurface angle is on cementum or dentin. Composite resin restoration of cervical lesion shrink toward enamel margin due to polymerization contraction. This shrinkage has clinical problem such as microleakage and secondary caries. Several methods to diminish contraction stress of composite resin restoration, such as modifying cavity form and building up restorations in several increments have been attempted. The purpose of this study was to compare polymerization contraction stress of composite resin in Class V cavity subjected to cavity forms and placement methods. In this study, finite element model of 5 types of Class V cavity was developed on computer tomogram of maxillary central incisor. The types are : 1) Box cavity 2) Box cavity with incisal bevel 3) V shape cavity 4) V shape cavity with incisal bevel 5) Saucer shape cavity. The placement methods are 1) Incisal first oblique incremental curing 2) Bulk curing. An FEM based program for light activated polymerization is not available. For simulation of curing dynamics, time dependent transient thermal conduction analysis was conducted on each cavity and each placement method. For simulation of polymerization shrinkage, thermal stress analysis was performed with each cavity and each placement method. The time-temperature dependent volume shrinkage rate, elastic modulus, and Poisson's ratio were determined in thermal conduction data. The results were as follows : 1. With all five Class V cavifies, the highest Von Mises stress at the composite-tooth interface occurred at gingival margin. 2. With box cavity, V shape cavity and saucer cavity, Von Mises stress at gingival margin of V shape cavity was lower than the others. And that of box cavity was lower than that of saucer cavity. 3. Preparing bevel at incisal cavosurface margin decreased the rate of stress development in early polymerization stage. 4. Preparing bevel at incisal cavosurface margin of V shape cavity increased the Von Mises stress at gingival margin, but decreased at incisal margin. 5. At incisal margin, stress development by bulk curing method was rapid at early stage. Stress development by first increment of incremental curing method was also rapid but lower than that by bulk curing method, however after second increment curing final stress was the same for two placement methods. 6. At gingival margin, stress development by incremental curing method was suddenly rapid at early stage of second increment curing, but final stress was the same for two placement methods.

• 한국재료학회지
• /
• 제12권7호
• /
• pp.580-586
• /
• 2002

The effect of processing and designing variables such as pouring temperature(1400 or $1500^{\circ}C$), inoculation and risering design(T and H type) on the formation of defects such as external depression, primary and secondary shrinkage cavities in GC150 gray cast iron was investigated. In T type risering design, external depression or primary shrinkage cavity due to liquid contraction was formed in all of the eight cases. Regardless of its modulus value, the riser could not function properly in T type risering design because directional solidification was not promoted toward the riser. On the other hand, the four cases of H type risering design in which thermal sleeves were set onto the risers produced defect-free castings. In both types of the risering designs, secondary shrinkage cavity caused by solidification contraction was not observed in the casting because of the expansion pressure due to graphite precipitation and the application of rigid pep-set mold. The degree of external depression or primary shrinkage cavity was reduced with lowered pouring temperature. The effect of inoculation was diminished because of the high carbon equivalent of GC 150 gray cast iron.

• 한국재료학회지
• /
• 제13권2호
• /
• pp.74-80
• /
• 2003

The effects of risering design and alloying element on the formation of defects such as external depression, primary and secondary shrinkage cavities in ductile cast iron were investigated. Two types of risering design for the cylindrically step-wise specimen, No. 1(progressive solidification) and No. 2(directional solidification) risering designs, were prepared and six different alloy compositions were casted. In the No. 1 risering design, external depression or primary shrinkage cavities due to liquid contraction were observed in all the specimens from SG 10 to SG 60. The defects caused by liquid contraction seemed to be more affected by risering design than alloying elements. The secondary shrinkage cavities were also observed in all the specimens but a swollen surface was not observed in all the castings. The primary shrinkage cavities were located right under the top surface or connected to the top surface, and were characterized by smooth surfaces. On the other hand, the secondary shrinkage cavities were positioned in the thermal center of the specimen steps 3 and 4, and characterized by rough surfaces. In the No. 2 risering design, no external depression or primary shrinkage cavities due to liquid contraction were observed in all the specimens from SG 10 to SG 60. However, the secondary shrinkage cavities were formed in the thermal center of specimens SG 40, 50 and 60. Like the No. 1 risering design, a swollen surface was not observed in all the castings.

• Restorative Dentistry and Endodontics
• /
• 제19권2호
• /
• pp.641-654
• /
• 1994

This study was executed to evaluate adaptability of dentin bonding agents to dentinal wall with measuring contraction gap on interface between cavity wall and composite resin by SEM study. 6 kinds of dentin bonding agents were investigated for this study : Gluma, Super Bond C & B, All bond 2, Scotchbond multipurpose, Scotchbond 2 and Clearfil photo bond. 30 of fresh extracted teeth were randomly selected and divided into 6 groups with each 5. The round shaped cavities with 3mm dia. and 1.5mm depth were prepared on cementoenamel junction of buccal surface of teeth. Dentin bonding agents were applied to cavity wall and then the composite resin was filled in the cavity. Specimens were sectioned longitudinally on buccal surface. Sectioned aspects of specimens were impressioned with rubber base materials and finally precise replica were made of epoxy resin poured in negative impression. Contraction gaps were examined on interface between cavity wall and composite resin under condition of 200 and 2000 magnification of SEM. The results were as follows. 1. There were no gap on interface between enamel and composite resin in all specimens, but gaps were mainly exhibited on apical side of lateral wall of dentin of cavity. 2. In Gluma, 2 cases of 5 specimens exhibited excellent adaptation to the cavity wall, indicating no gaps on interface between cavity wall and composite resin. The other specimens showed gaps with range of $0{\sim}15{\mu}m$ width. 3. In Super Bond C & B, gaps with range of $0{\sim}10{\mu}m$ width were mainly exhibited on apical side of lateral wall of dentin of cavity. 4. In All bond 2, all specimens showed the most exellent adaptation to cavity wall when compared to the other materials, indicating no gap interface between cavity wall and composite resin. 5. In Scotchbond multipurpose, gaps with range of $0{\sim}10{\mu}m$ width were locally located on cavity wall. 6. In Scotchbond 2, all specimens showed great amount of gap with range of $5{\sim}25{\mu}m$, indicating the worst adaptation to cavity wall compared to the other materials. 7. In Clearfil photo bond, 2 case of 5 specimens exhibited exellent adaptation to cavity wall, indicating no gap. the other specimens showed gap with range of $0{\sim}15{\mu}m$ width on inferface between cavity wall and composite resin.

• 한국주조공학회지
• /
• 제15권5호
• /
• pp.494-506
• /
• 1995

Test castings in plate, disc, and cubic shaped castings for 0.2wt.% carbon and stainless steel have been poured to examine the effects of the riser dimensions including riser neck on the casting soundness. Three empirical methods were chosen in risering of steel castings. A computer program of solidification analysis considering liquid and solidification contraction was developed to apply for riserdesign calculated by using their methods in plate, disc, and cubic shaped castings, and to calculate the position and dimension of shrinkage cavity in complex shaped casting. The potential of present method has been successfully demonstrated by comparing predicted cavity shapes with those obtained in a series of experimental castings. Three empirical methods can be used in a practical way to make a rapid estimation of tie minimum riser diameter, but they can not provide a criterion of casting soundness with shape and material on all occasions. The shape and position of shrinkage cavity can be successfully predicted both using the present method and using risering calculated by their methods regardless of the shape and cast material.

• 대한소아치과학회지
• /
• 제33권2호
• /
• pp.233-243
• /
• 2006

와동 형성시 C-factor와 충전방법이 복합레진 수복물에서의 수축 응력에 미치는 영향을 평가하고자 발거된 소구치를 대상으로 C-factor가 3.6과 1.0인 와동을 각각 형성한 후 hybrid형 복합레진인 $Z-250^{TM}$(3M ESPE U.S.A.)과 flowable형 복합레진인 $Filtek\;flow^{TM}$(3M ESPE U.S.A.)를 사용하여 layering을 시행하고 광중합하면서 strain gauge법을 이용하여 치질에서의 수축 응력을 측정하였다. 시편을 절단하여 레진과 상아질 사이 계면의 접착상태를 주사전자현미경으로 관찰한 결과 다음과 같은 결과를 얻었다. 1. C-factor에 따른 수축 응력을 측정한 결과 C-factor가 3.7인 제 1군과 제 2군 그리고 제 5군이 900초 후 각각 0.11, 0.07, 0.07 MPa로 C-factor가 1.0인 제 3군과 제 4군의 0.05와 0.04 MPa에 비해 크게 나타났다(P<0.05). 1,800초 후에는 제 1군, 제 5군, 제 2군, 제 3군, 제 4순으로 크게 나타났으나 제 2군과 제 3군 그리고 제 3군과 제 4군 사이에는 유의성이 없었다. 2. 재료에 따른 수축 응력의 차이는 C-factor가 3.7인 와동의 경우 hybrid형 레진인 Filtek $Z-250^{TM}$이 flowable 레진인 $Filtek\;flow^{TM}$에 비해 수축 응력이 크게 나타났으나(P<0.05), C-factor가 1.0인 와동의 경우 재료의 차이에 따른 수축응력의 유의한 차이가 없었다. 3. Layering에 따른 수축 응력은 Filtek $Z-250^{TM}$을 layering 없이 bulk 충전한 제 1군에 비해 flowable 레진을 layering한 제 5군이 전 측정 시간대에 걸쳐 수축 응력이 유의하게 낮게 나타났다(P<0.05). 4. C-factor가 3.7인 제 1군과 제 2군 제 5군은 900초까지 수축 응력이 증가하다 이후 점차 감소하는 경향을 보였다. 5. C-factor가 1.0인 와동의 경우 충전용 레진 종류에 관계없이 레진과 와동벽 사이에 긴밀한 접착 상태를 보였으나 C-factor가 3.7인 와동의 경우 부분적으로 틈이 관찰되었다. 전반적으로 와동저에 비해 와동벽에서 틈이 더 많이 관찰되었다. 이상의 결과를 종합하여 보면 복합레진 수복시 수축응력에 따른 합병증을 예방하기 위해 C-factor를 크지 않게 와동을 설계, 형성하여야 하며 C-factor가 클 경우 flowable 레진을 이장하는 등 재료적인 면에서의 선택과 적용법이 중요할 것으로 사료된다.

• 한국재료학회지
• /
• 제13권5호
• /
• pp.297-302
• /
• 2003

The effects of risering design and alloying element on the formation of defects such as external depression, primary and secondary shrinkage cavity in gray cast iron were investigated. Two types of risering design for the cylindrically step-wise specimen, No. 1(progressive solidification) and No. 2(directional solidification) risering designs, were prepared and five different alloy compositions were casted. In the No. 1 risering design, external depression or primary shrinkage cavity due to liquid contraction was observed in all the specimens from ISO 150 to ISO 350. The primary shrinkage cavity was located right under the top surface or connected to the top surface, and was characterized by smooth surface. Its size increased with an increase in ISO number. However, neither secondary shrinkage cavity nor swollen surface was observed in all the castings. In the No.2 risering design, neither primary shrinkage cavity nor secondary shrinkage cavity was observed in all the specimens due to proper risering design. A swollen surface was also not observed in all the castings with the application of pep-set mold.

• 대한치과보존학회:학술대회논문집
• /
• 대한치과보존학회 2001년도 추계학술대회(제116회) 및 13회 Workshop 제3회 한ㆍ일 치과보존학회 공동학술대회 초록집
• /
• pp.558.1-558
• /
• 2001

Flowable resin composite is a relatively new restorative material. It has been reported that a low viscosity, low modulus intermediate resin applied between the bonding agent and restorative resin act as an "elastic buffer" that can relieve contraction stress. This in-vitro study aimed to evaluate the effect of flowable composite resin as a restorative material on regional tensile bond stredgth to cervical wedge shaped cavity walls. (omitted)