• 접착 및 계면
• /
• 제9권2호
• /
• pp.24-31
• /
• 2008

본 연구에서는 EVA 에멀젼에 내수성 및 기계적 특성을 향상시키기 위하여 금속 이온 가교제인 calcium hydroxide 및 magnesium carbonate를 사용하여 이온성 가교결합을 도입하였다. EVA 에멀젼 필름의 가교밀도, 열적특성, 표면자유에너지 그리고 인장강도, 파단신율 및 인열강도 특성을 고찰하였다. 금속 이온 가교제 양이 증가함에 따라 EVA 에멀젼의 가교밀도는 증가하였고, 이에 내수성과 $T_g$ 값도 증가하였다. 그러나 EVA 에멀젼 필름의 표면에너지 및 기계적 특성들은 다소 다른 거동을 보였다. Calcium hydroxide 0.4% 그리고 magnesium carbonate 0.5%를 첨가한 경우가 EVA 에멀젼에 강한 이온성 가교결합이 형성되어 가장 높은 표면 자유에너지 값과 인장강도 및 인열강도를 보였다. 그러므로 본 연구에서 calcium hydroxide 및 magnesium carbonate와 같은 금속 이온 가교제가 EVA 에멀젼의 내수성과 기계적 물성을 향상시킴을 확인하였다.

• 한국식품저장유통학회지
• /
• 제12권2호
• /
• pp.112-116
• /
• 2005

본 연구에서는 시판되는 3종의 칼슘 용해에 미치는 식초의 영향을 조사하였다. 식초의 초기총산에 따른 영향을 조사한 결과 초기총산과 칼슘첨가량이 높을수록 용해 후 pH와 잔사량은 낮게, 총산과 칼슘함량은 높게 나타났다. 식초 함량에 따른 영향을 조사한 결과 식초함량이 높을수록 pH는 낮게 총산은 높게 나타났으며, 칼슘함량은 해조칼슘과 탄산칼슘에서 높게 나타났다. 식초를 이용하여 해조칼슘과 탄산칼슘의 포화농도를 조사한 결과 해조칼슘은 $7.0\%$ (w/v), 탄산칼슘은 $6.0\%$(w/v) 농도이며 이때 칼슘함량은 $2,234\;mg\%$와 $2,490\;mg\%$로 나타났다.

• Geomechanics and Engineering
• /
• 제32권3호
• /
• pp.347-359
• /
• 2023

With the development of infrastructure, there is a critical shortage of filling materials all over the word. However, a large amount of silt accumulated in the lower reaches of the Yellow River is treated as waste every year, which will cause environmental pollution and waste of resources. Microbial induced calcium carbonate precipitation (MICP) technology, with the advantage of efficient, economical and environmentally friendly protection, is selected to solidify the abandoned Yellow River silt with poor mechanical properties into high-quality filling material in this paper. Based on unconfined compressive strength (UCS) test, determination of calcium carbonate (CaCO₃) content and scanning electron microscope (SEM) test, the effects of cementation solution concentration, treatment times and relative density on the solidification effect were studied. The results show that the loose silt particles can be effectively solidified together into filling material with excellent mechanical properties through MICP technology. The concentration of cementation solution have a significant impact on the solidification effect, and the reasonable concentration of cementation solution is 1.5 mol/L. With the increase of treatment times, the pores in the soil are filled with CaCO₃, and the UCS of the specimens after 10 times of treatment can reach 2.5 MPa with a relatively high CaCO₃ content of 26%. With the improvement of treatment degree, the influence of relative density on the UCS increases gradually. Microscopic analysis revealed that after MICP reinforcement, CaCO₃ adhered to the surface of soil particles and cemented with each other to form a dense structure.

• 한국식품위생안전성학회지
• /
• 제19권4호
• /
• pp.203-208
• /
• 2004

꼬막, 참굴, 바윗굴 및 가리비 등 폐기되는 몇 종의 패각류를 이용하여 칼슘 보강용 식품 첨가제의 원료로써 사용 할 수 있는 고순도의 탄산칼슘을 제조하고자 하였다. 꼬막 패각을 $900^{\circ}C$에서 5시간 회화한 회화분의 칼슘 함량이 $64.9\%$로 가장 높게 나타났으며, 가리비 $62.5\%$, 참굴 $62.4\%$, 바윗굴 $61.5\%$ 순이었다 백색도는 가리비 패각 회화분의 경우 81.6-85.8로서 패각류 중 가장 높았다. 꼬막 패각 회화분$(Ca\;39.92\%)$에 ammonium chloride process(ACP)와 ammonium nitrate process(ANP)법을 적용하여 제조한 $CaCO_3$의 Ca 함량은 $40.03-40.04\%$로 높아졌고, ANP법에 의해 제조한 pH 조정 시료의 경우가 $40.04\%$로서 가장 높았으며, 이 방법들에 의해 불순물이 거의 대부분 제거되는 것으로 나타났다. ACP법과 AMP법에 의해 제조한 $CaCO_3$의 백색도는 101.0-101.5로 매우 우수하였으며, 칼슘보강용 식품첨가제로서 사용될 가능성이 충분하다고 판단된다.

• 한국식품과학회지
• /
• 제39권1호
• /
• pp.33-38
• /
• 2007

밀가루에 소금을 0, 2 및 4%를 첨가하였을 경우, Mixograph의 peak time은 밀가루의 종류에 관계없이 소금 첨가량이 증가함에 따라서 증가함을 알 수 있었으나 박력분의 경우에는 유의적인 차이를 나타내지는 않았다. Peak height와 width at peak도 소금 첨가량이 증가함에 따라 증가하는 경향을 나타내었으나 강력분과 중력분에서는 유의적인 차이를 나타내지 않았다. Width at 8 min의 경우에는 모든 밀가루에서 소금 첨가량이 증가함에 따라 증가하는 경향을 나타내었다. Sodium carbonate를 0, 0.5, 1.0 및 1.5의 농도로 밀가루에 첨가하여 Mixograph 특성을 관찰한 결과 밀가루의 종류에 관계없이 0.5% 첨가 시 peak time이 거의 2배정도 증가하였다가 그 보다 높은 농도에서는 다시 감소된 반면, peak height는 sodium carbonate 첨가량이 증가함에 따라서 감소하는 경향을 보였다. Mixograph peak time과 단백질 함량 및 침전가와는 유의적인 상관이 없었으나, peak height, width at peak 및 width at 8min과는 모두 정의 상관관계를 보여 주었다. 반죽의 초기호화온도, 최고점도, 최소점도, 최종점도는 밀가루의 종류에 관계없이 소금의 첨가량이 증가함에 따라 증가하는 경향을 나타내었으며, 최고점도, 최소점도 및 최종점도는 모든 밀가루에서 sodium carbonate 첨가량이 증가함에 따라서 유의적으로 증가하는 경향을 보였다. 초기호화온도와 보수율 및 알칼리수 흡수율과는 정의 상관이 있었으나, 보수율과 최고점도, 최소점도 및 최종점도와는 모두 부의 상관관계를 보여 주었다.

• Carbon letters
• /
• 제24권
• /
• pp.62-72
• /
• 2017

The aim of this work was to evaluate the dielectric properties of impregnated and activated palm kernel shells (PKSs) samples using two activating agents, potassium carbonate ($K_2CO_3$) and sodium hydroxide (NaOH), at three impregnation ratios. The materials were characterized by moisture content, carbon content, ash content, thermal profile and functional groups. The dielectric properties were examined using an open-ended coaxial probe method at various microwave frequencies (1-6 GHz) and temperatures (25, 35, and $45^{\circ}C$). The results show that the dielectric properties varied with frequency, temperature, moisture content, carbon content and mass ratio of the ionic solids. PKSK1.75 (PKS impregnated with $K_2CO_3$ at a mass ratio of 1.75) and PKSN1.5 (PKS impregnated with NaOH at a mass ratio of 1.5) exhibited a high loss tangent ($tan{\delta}$) indicating the effectiveness of these materials to be heated by microwaves. $K_2CO_3$ and NaOH can act as a microwave absorber to enhance the efficiency of microwave heating for low loss PKSs. Materials with a high moisture content exhibit a high loss tangent but low penetration depth. The interplay of multiple operating frequencies is suggested to promote better microwave heating by considering the changes in the materials characteristics.

• Journal of Nutrition and Health
• /
• 제27권5호
• /
• pp.473-482
• /
• 1994

This study was to compare the bioavailability of calcium from anchovy and tofu to those of calcium from calcium carbonate(CaCO3)as the control diet and non-fat dry milk(NFDM). Rats weighing 50-60g were placed on experimental diets and deionized water at free access for 4 weeks. Diets contained 0.2% calcium from calcium-carbonate, NFDM, anchovy, tofu or 0.5% calcium as obtained were as follows : 1) No significant differences in the apparent absorption of calcium(62.5%-71.0%) were observed in the rats fed four different calcium sources at the level of 0.2% while 0.5% calcium diet group apparently absorbed calcium less efficiently(52.2%). 2) Bone length of tibia and femur was not significantly different among the groups, though 0.5% calcium of control group showed slightly longer length. 3) Tibia fat-free dry weights of 0.2% calcium of NFDM and anchovy diet groups were not significantly different from that of 0.5% calcium of control group. For femurs NFDM, anchovy and tofu groups were similar in their fat-free dry weight to that of 0.5% calcium group. 4) For calcium contents tibia contents tibia from anchovy treated group showed higher value than calcium-carbonate and tofu groups and the value was not significantly different from that of 0.5% calcium group. In femur NFDM, tofu and calcium-carbonate groups were not significantly different in their calcium content but 0.5% calcium group had higher level of calcium than 0.2% calcium groups. 5) The normalized values(NV) show that there was no significant differences in NV among 0.2% CaCO3 anchovy and tofu groups, while NV of NFDM group was significantly lower than that of calcium-carbonate group. NV of 0.5% calcium group was a little more than 50% of those in 0.2% calcium groups. Though the values obtained for the calcium bioavailability were somewhat variable among experimental products, it was demonstrated that anchovy and tofu are as good as NFDM for the dietary calcium provider when calcium intake is at marginal level.

• Journal of Electrochemical Science and Technology
• /
• 제11권1호
• /
• pp.60-67
• /
• 2020

In this study, copper (II) oxide powder for electroplating was prepared by recovering CuCl₂ from NaClO₃ type etching wastes via recovered non-sintering two step chemical reaction. In case of alkali copper carbonate [mCuCo₃·nCu(OH)₂], first reaction product, CuCo₃ is produced more than Cu(OH)₂ when the reaction molar ratio of sodium carbonate is low, since m is larger than n. As the reaction molar ratio of sodium carbonate increased, m is larger than n and Cu(OH)₂ was produced more than CuCO₃. In the case of m has same values as n, the optimum reaction mole ratio was 1.44 at the reaction temperature of 80℃ based on the theoretical copper content of 57.5 wt. %. The optimum amount of sodium hydroxide was 120 g at 80℃ for production of copper (II) oxide prepared by using basic copper carbonate product of first reaction. At this time, the yield of copper (II) oxide was 96.6 wt.%. Also, the chloride ion concentration was 9.7 mg/L. The properties of produced copper (II) oxide such as mean particle size, dissolution time for sulfuric acid, and repose angle were 19.5 mm, 64 second, and 34.8°, respectively. As a result of the hole filling test, it was found that the copper oxide (II) prepared with 120 g of sodium hydroxide, the optimum amount of basic hydroxide for copper carbonate, has a hole filling of 11.0 mm, which satisfies the general hole filling management range of 15 mm or less.

• 자원환경지질
• /
• 제29권1호
• /
• pp.25-33
• /
• 1996

Stable isotopic ratios of the carbonate rocks and chemical compositions of the matrix of pebble bearing phyllitic rocks known as the Hwanggangri Formation, which are in hot debate on their origin such as tillite, debris flow and turbidite, were determined to interpret their depositional environment. Argillaceous matrix of the pebble bearing phyllitic rocks has a high content of CaO (av. 19.5%) and MgO (av. 8.3%), corresponding to calcareous sandy shale. No difference of chemical compositions including trace elements and REE is in the matrices between the Hwanggangri and the Kunjasan Formations. Carbonate rocks from the Okchon zone and outside of the zone range $-2.5{\sim}+6.1$‰ in ${\delta}^{13}C$ and $+5.8{\sim}+25.9$‰ in ${\delta}^{18}O$, indicating normal marine limestone. However, unusally $^{13}C$ enriched carbonate rocks might be deposited in the highly evaporated sedimentary basin. A wide variation of ${\delta}^{18}O$ values is responsible for metamorphism with a $^{18}O$ depleted meteoric water. Isotopic equilibrium temperatures by graphite-calcite geothermometer show a higher metamorphic temperature ($547{\sim}589^{\circ}C$) in the Okchon zone than those ($265{\sim}292^{\circ}C$) in the Samtaesan Formation of the Chosun group. Rhythmic alternation of relatively thin shale with thin limestone in the Kounri Formation is not cherty layer but thin limesilicate bed by metasomatic replacement. Judging from the isotopic and chemical compositions of the carbonate rocks and calcareous matrix of the pebble bearing phyllitic rocks, the Hwangganari Formation was deposited in the shallow marine environment favorable to debris flow.

• 펄프종이기술
• /
• 제29권1호
• /
• pp.7-12
• /
• 1997

This study was intended to investigate the proper shape and size of calcium carbonate for the improvement of paper properties and its end use performance. We loaded calcium carbonate of various shapes and size in the handsheet and measured their physical and optical properties. Results obtained from the study are summarized as follows : 1. Due to different particle shapes and sizes, precipitated calcium carbonate (PCC) contributed greater to bulk improvement than ground calcium carbonate (GCC). Scalenohedral form of PCC produced the bulkiest sheet, GCC made the sheet bulkier as average particle size increases. 2. Tensile strength increased as average particle size was increasing. GCC kept tensile strength more effectively than PCC. The effect of particle size on tensile strength was much more pronounced as filler addition level was increasing. 3. Over the average particle size of 6.99$\mu$m, GCC gave much higher burst strength and internal bond than PCC did. In the filler levels of 20% and 30%, GCC by using bigger size fillers showed 50~100% improvement in some cases than PCC at the same filler content. 4. Tear strength increased as average particle size was increasing. At the filler level of 30%, PCC decreased tear greatly. 5. Over the average particle size of 13.56$\mu$m, GCC kept bending stiffness greater than PCC. Due to its shape, Scalenohedral form of PCC showed higher stiffness than others at the same particle size. 6. Cubic and acicular form of PCC improved light scattering coefficient very effectively. Light scattering coefficient of GCC decreased as average particle size increased. 7. Both of particle shape and size of filler were important factor in developing optical properties and bending stiffness. Particle size was the only important factor in developing other strength properties