• Nuclear Engineering and Technology
• /
• v.56 no.1
• /
• pp.180-188
• /
• 2024

This research examined consumption-based carbon emission reduction by nuclear energy consumption and environmental tax while considering the context of trade globalization in the highest five emitter nations from 1990 to 2020. This study used various empirical methodologies, including preliminary analysis to check the stationarity and cointegration, the CS-ARDL for long-run analysis, CCEMG, AMG for robustness, and the D-H causality test for short-term pairwise causation. The results indicated that nuclear energy consumption, environmental tax, and trade globalization help to mitigate consumption-based carbon emissions while economic growth and population density boost carbon emissions. Furthermore, the results also found two-way casual connection exists between nuclear energy consumption, population density, and consumption-based carbon emissions. Thus, the results emphasize the need for government policies that encourage nuclear energy and environmental tax as a strategy to reduce carbon emissions and achieve and maintain environmental development.

• Journal of Forest and Environmental Science
• /
• v.32 no.2
• /
• pp.120-128
• /
• 2016

Forest sequesters large terrestrial carbon which is stored in the biomass of tree and plays a key role in reducing atmospheric carbon. Thus, the objectives of the present study were to assess the growing stock, above ground biomass and carbon in trees of Ponda watershed of Rajouri district (J&K). IRS-P6 LISS-III satellite data of October 2010 was used for preparation of land use/land cover map and forest density map of the study area by visual interpretation. The growing stock estimation was done for the study area as well as for the sample plots laid in forest and agriculture fields. The growing stock and biomass of trees were estimated using species specific volume equations and using specific gravity of wood, respectively. The total growing stock in the study area was estimated to be $0.25million\;m^3$ which varied between $85.94m^3/ha$ in open pine to $11.58m^3/ha$ in degraded pine forest. However in agriculture area, growing stock volume density of $14.85m^3/ha$ was recorded. Similarly, out of the total biomass (0.012 million tons) and carbon (0.056 million tons) in the study area, open pine forest accounted for the highest values of 43.74 t/ha and 19.68 t/ha and lowest values of 5.68 t/ha and 2.55 t/ha, respectively for the degraded pine forest. The biomass and carbon density in agriculture area obtained was 5.49 t/ha and 2.47 t/ha, respectively. In all the three forest classes Pinus roxburghii showed highest average values of growing stock volume density, biomass and carbon.

• Korean Journal of Materials Research
• /
• v.31 no.5
• /
• pp.301-311
• /
• 2021

The conversion of all carbon preforms to dense SiC by liquid infiltration can become a low-cost and reliable method to form SiC-Si composites of complex shape and high density. Reactive sintered silicon carbide (RBSC) is prepared by covering Si powder on top of 0.5-5.0 wt% Y₂O₃-added carbon preforms at 1,450 and 1,500℃ for 2 hours; samples are analyzed to determine densification. Reactive sintering from the Y₂O₃-free carbon preform causes Si to be pushed to one side and cracking defects occur. However, when prepared from the Y₂O₃-added carbon preform, an SiC-Si composite in which Si is homogeneously distributed in the SiC matrix without cracking can be produced. Using the Si + C = SiC reaction, 3C and 6H of SiC, crystalline Si, and Y₂O₃ phases are detected by XRD analysis without the appearance of graphite. As the content of Y₂O₃ in the carbon preform increases, the prepared RBSC accelerates the SiC conversion reaction, increasing the density and decreasing the pores, resulting in densification. The dense RBSC obtained by reaction sintering at 1,500 ℃ for 2 hours from a carbon preform with 2.0 wt% Y₂O₃ added has 0.20 % apparent porosity and 96.9 % relative density.

• Carbon letters
• /
• v.4 no.1
• /
• pp.36-39
• /
• 2003

Carbon and carbon-based materials are used in nuclear reactors and there has recently been growing interest to develop graphite and carbon based materials for high temperature nuclear and fusion reactors. Efforts are underway to develop high density carbon materials as well as amorphous isotropic carbon for the application in thermal reactors. There has been research on coated nuclear fuel for high temperature reactor and research and development on coated fuels are now focused on fuel particles with high endurance during normal lifetime of the reactor. Since graphite as a moderator as well as structural material in high temperature reactors is one of the most favored choices, it is now felt to develop high density isotropic graphite with suitable coating for safe application of carbon based materials even in oxidizing or water vapor environment. Carboncarbon composite materials compared to conventional graphite materials are now being looked into as the promising materials for the fusion reactor due their ability to have high thermal conductivity and high thermal shock resistance. This paper deals with the application of carbon materials on various nuclear reactors related issues and addresses the current need for focused research on novel carbon materials for future new generation nuclear reactors.

• Composites Research
• /
• v.12 no.3
• /
• pp.8-16
• /
• 1999

Carbon woven fabric/C/SiC composites were fabricated by multiple impregnations of carbon woven fabric/carbon preform with the polymer precursor of SiC, i.e., polycarbosilane. In addition, two kinds of low density carbon/carbon preforms which had different fiber volume fraction and fiber orientation, i.e., a carbon woven fabric(${\thickapprox}$55 vol%)/carbon and a chopped carbon fiber${\thickapprox}$40 vol%)/carbon composites, were reaction-bonded with a silicon melt at 1$700^{\circ}C$ in a vacuum to fabricate dense carbon fiber/Si/SiC composites. The reaction-bonding process increased the density to ~2.1 g/$cm^3$ from 1.6 g/$cm^3$ and 1.15 g/$cm^3$ of a carbon woven and a chopped carbon preforms, respectively. All of the composites fractured with extensive fiber pull-out. The higher the density the higher the stiffness and proportional limit stress. The mechanical properties obtained from a three-point bend and tension tests were compared. The ratios of the peak tensile stresses to the bending strengths of a carbon woven and a chopped carbon composites were about one-third, respectively. The carbon woven fabric/Si/SiC composites with density of 2.06 g/$cm^3$ showed ~120 MPa of ultimate strength and ~80 MPa of proportional limit in bend testing.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.4
• /
• pp.160-164
• /
• 2007

Carbon nanofibers were deposited on silicon oxide substrate by thermal chemical vapor deposition method. For the enhancement of the characteristics of carbon nanofibers, the source gases ($C_2H_2,\;H_2$) flows were intentionally manipulated as the cyclic on/off modulation of $C_2H_2$ flow. By the cyclic modulation process during the initial deposition stage, the formation density of carbon nanofibers on the substrate could be much more enhanced. The diameter of as-grown carbon nanofibers was also reduced by the cyclic modulation process. The cause for the variation in the characteristics of carbon nanofibers by the cyclic modulation process was discussed in association with the hydrogen gas etching ability.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.5
• /
• pp.477-479
• /
• 2006

Carbon films was grown on Si substrates using the method of electrolysis for methanol liquid. Deposition parameters for the growth of the carbon films were current density for the electrolysis, methanol liquid temperature and electrode spacing between anode and cathode. We examined electrical resistance and the surface morphology of carbon films formed under various conditions specified by deposition parameters. It was clarified that the high electrical resistance carbon films with smooth surface morphology are grown when a distance between the electrodes was relatively wider. We found that the electrical resistance in the films was independent of both current density and methanol liquid temperature for electrolysis. The temperature dependence of the electrical resistance in the low resistance carbon films was different from one obtained in graphite.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.553-554
• /
• 2006

Carbon films was grown on Si substrates using the method of electrolysis for methanol liquid. Deposition parameters for the growth of the carbon films were current density for the electrolysis. methanol liquid temperature and electrode spacing between anode and cathode. We examined electrical resistance and the surface morphology of carbon films formed under various conditions specified by deposition parameters. It was clarified that the high electrical resistance carbon films with smooth surface morphology are grown when a distance between the electrodes was relatively wider. We found that the electrical resistance in the films was independent of both current density and methanol liquid temperature for electrolysis. The temperature dependence of the electrical resistance in the low resistance carbon films was different from one obtained in graphite.

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.2
• /
• pp.23-27
• /
• 2008

As a biofuel source, direct photosynthetic/metabolic biofuel cells (DPBFC) use cyanobacteria whose photosynthesis and metabolization reactions can convert light energy to electricity, In our previous work, we fabricated a prototype micro-DPBFC that could generate a peak current density of $36{\mu}A/cm^{2}$ and a maximum power density of $270nW/cm^{2}$. In this study, we improve on the previous results by using carbon micro electromechanical systems (C-MEMS), formed from the pyrolysis of patterned photoresist, to fabricate carbon electrodes of an arbitrary shape and controlled porosity to increase the surface area. With these new C-MEMS electrodes, the maximum power density of the micro-DPBFC was $516nW/cm^{2}$, a performance twice as good as the results of our previous work.

• Applied Chemistry for Engineering
• /
• v.4 no.4
• /
• pp.692-700
• /
• 1993

Corrosivities and catalytic activities of platinum-transition metal alloy catalyses loaded on carbon substrate and were studied by electrochemical method using a unit cell. And the analysis of Pt-alloy catalyst was conducted by x-ray diffractometer. Among the catalysts, the Pt-Mo/carbon, Pt-Fe-Co/carbon and Pt-Fe/carbon catalyst showed more excellent cathodic current densities than others. It was found that most of cathodic current density for the Pt-Mo/carbon electrode was $120mA/cm^2$. The current density of the Pt-Fe-Co/carbon was much higher than that of Pt/carbon, reaching $200mA/cm^2$.