• Title/Summary/Keyword: camera vibration

Search Result 239, Processing Time 0.032 seconds

A Study on the Evaluation of Famage Zone around Tunnel Induced by Blasting (발파에 의한 터널 주변 암반의 손상영역 평가에 관한 연구)

  • 장수호;신일계;최용근;이정인
    • Journal of the Korean Geotechnical Society
    • /
    • v.16 no.5
    • /
    • pp.129-140
    • /
    • 2000
  • 최근들어 핵폐기물 지하처분장을 중심으로 터널굴착에 의한 주변 암반의 손상상태와 암반특성의 변화를 정량적으로 평가하기 위한 시도가 이루어지고 있다. 이는 암반의 지지력을 적극적으로 이용하는 NATM개념에 의해 터널을 시공할 셩우 안정성 해석과 최적 보강설계를 위해 필수적인 사항으로 고려된다. 그러나 현재까지 암반 손상영역을 평가하기 위해 제시된 여러 방법들은 아직까지 그 적용성과 타당성이 충분히 검증되지 못한 실정이다. 이 연구에서는 코어시추, 실험실시험, 발파진동측정, 보어홀 카메라 등의 여러 방법에 의해 손상영역을 정량적으로 평가하고자 하였으며 가 방법의 적용성을 검토하였다. 암반상태 및 발파조건을 달리하여 시험발파를 수행하였으며 발파 후에 터널벽면에 수직하게 시추를 하여 암석코어를 채취한 뒤 손상정도에 따른 암석의 물리적, 역학적 특성들? 변화를 정량적으로 나타내고자 하였다. 코어 채취후 시축공에 보어홀 카메라를 사용하여 손상영역을 시각적으로 판별하고자 하였으며 발파진동 측정결과로부터 손상영역을 예측하고 채취한 암석시표에 대한 실험실시험 결과와 비교하여 적용성을 검토하였다.

  • PDF

A comparative study of cavitation inception of naval ship's propeller using on-board noise and vibration signals (선체 부착 소음/진동 센서를 이용한 함정 추진기 캐비테이션 초생 분석 비교 연구)

  • Hongseok Jeong;Hanshin Seol
    • The Journal of the Acoustical Society of Korea
    • /
    • v.42 no.3
    • /
    • pp.243-249
    • /
    • 2023
  • The occurrence of cavitation on the propeller is directly linked to the naval ship's survivability, and it is necessary to design a propeller shape that delays the cavitation inception. However, the propeller cavitation can occur under various operating conditions, thus it is important to identify whether the propeller cavitation exists during operation as well as in the design phase. To this end, it is necessary to use noise or vibration signals on board to monitor the cavitation inception. In this study, a hydrophone and an accelerometer were installed on the ship hull right above the propeller to compare the performance of analyzing cavitation inception between acoustic and vibration signals. Also, a high speed camera was used to visually observe the occurrence of cavitation through an observation window. The measured results showed that the spectral shapes between acoustic and vibration signals were different, but the level increases at each frequency band and the overall level of the frequency band from 1 kHz to 10 kHz showed a similar tendency. The Detection of Envelope Modulation On Noise (DEMON) analysis also showed similar results for both acoustic and vibration signals, confirming that both hydrophones and accelerometers can be utilized in the analysis of cavitation inception.

Design of High Speed Tensile Test Machine for Flow Stress under Intermediate Strain Rate Condition (중변형률 속도 유동응력 확보를 위한 고속 인장 실험기 설계)

  • Choung, Joonmo;Yoon, Sung-Won;Park, Sung-Ju;Kim, Younghun
    • Journal of Ocean Engineering and Technology
    • /
    • v.29 no.1
    • /
    • pp.34-44
    • /
    • 2015
  • A hydraulic tensile test machine (HSTM) is one of the devices used to obtain the flow stress of a material during high-speed elongation. This paper first describes some features of a newly built HSTM. The improvement histories of the upper and lower jigs, which are the most vital parts of the HSTM, are also presented. We have frequently witnessed test failures with 1st generation jigs and specimens due to slip between the jig and specimen. 2nd generation jigs provide more stable test results, but the use of a longer upper jig induces excessive vibration and consequently makes it difficult to attach an environment chamber. 3rd generation jigs have some advances in terms of the symmetric fastening between the upper jig and specimen, as well as an exemption from direct contact between the lower jig and specimen. The performance of an environment chamber is verified by high and low temperature tests. A high-speed displacement measurement system is introduced based on a high-speed camera and motion-tracking software with aid of a surface grid device for the specimen.

Image Deblurring Using Vibration Information From 3-axis Accelerometer (3축 가속도 센서의 흔들림 정보를 이용한 영상의 Deblurring)

  • Park, Sang-Yong;Park, Eun-Soo;Kim, Hak-Il
    • Journal of the Institute of Electronics Engineers of Korea SC
    • /
    • v.45 no.3
    • /
    • pp.1-11
    • /
    • 2008
  • This paper proposes a real-time method using a 3-axis accelerometer to enhance blurred images taken from a camera loaded in mobile devices. Blurring phenomenon is a smoothing effect occurring in photo images. Algorithms to cope with blurring phenomenon is essential since small-size mobile devices tremble severely by even a tiny hand-shaking of a user. In this paper, accurate sensing characteristics of the 3-axis accelerometer is acquired by applying the sensor in pendulum motion and the blurring phenomenon is modeled as a uniform distribution and Gaussian distribution. Also, non-Gaussian distributed model is observed in the experiment of real blurring phenomenon and a particular deblurring function is designed by reversing the model. It has been demonstrated that the application of trembling information to the deblurring function adequately removes the blurring phenomenon.

Defect Detection of Carbon Steel Pipe Weld Area using Infrared Thermography Camera (적외선 열화상 카메라를 이용한 탄소강관 용접부 결함검출)

  • Kwon, DaeJu;Jung, NaRa;Kim, JaeYeol
    • Tribology and Lubricants
    • /
    • v.30 no.2
    • /
    • pp.124-129
    • /
    • 2014
  • The piping system accounts for a large portion of the machinery structure of a plant, and is considered as a very important mechanical structure for plant safety. Accordingly, it is used in most energy plants in the nuclear, gas, and heavy chemical industries. In particular, the piping system for a nuclear plant is generally complicated and uses the reactor and its cooling system. The piping equipment is exposed to diverse loads such as weight, temperature, pressure, and seismic load from pipes and fluids, and is used to transfer steam, oil, and gas. In ultrasound infrared thermography, which is an active thermography technology, a 15-100 kHz ultrasound wave is applied to the subject, and the resulting heat from the defective parts is measured using a thermography camera. Because this technique can inspect a large area simultaneously and detect defects such as cracks and delamination in real time, it is used to detect defects in the new and renewable energy, car, and aerospace industries, and recently, in piping defect detection. In this study, ultrasound infrared thermography is used to detect information for the diagnosis of nuclear equipment and structures. Test specimens are prepared with piping materials for nuclear plants, and the optimally designed ultrasound horn and ultrasound vibration system is used to determine damages on nuclear plant piping and detect defects. Additionally, the detected images are used to improve the reliability of the surface and internal defect detection for nuclear piping materials, and their field applicability and reliability is verified.

Defect Detection of Ceramic Heating Plate Using Ultrasound Pulse Thermography (초음파 펄스 서모그라피를 이용한 세라믹 전열 판의 결함 검출)

  • Cho, Jai-Wan;Seo, Yong-Chil;Jung, Seung-Ho;Kim, Seung-Ho;Jung, Hyun-Kyu
    • Journal of the Korean Ceramic Society
    • /
    • v.43 no.4 s.287
    • /
    • pp.259-263
    • /
    • 2006
  • The applicability of UPT (Ultrasound Pulse Thermography) for real-time defect detection of the ceramic heating plate is described. The ceramic heating plate with superior insulation and high radiation is used to control the water temperature in underwater environment. The underwater temperature control system can be damaged owing to the short circuit, which resulted from the defect of the ceramic heating plate. A high power ultrasonic energy with pulse duration of 280 ms was injected into the ceramic heating plate in the vertical direction. The ultrasound excited vibration energy sent into the component propagate inside the sample until they were converted to the heat in the vicinity of the defect. Therefore, an injection of the ultrasound pulse wave which results in heat generation, turns the defect into a local thermal wave transmitter. Its local emission is monitored and recorded via the thermal infrared camera at the surface which is processed by image recording system. Measurements were Performed on 4 kinds of samples, composed of 3 intact plates and the defect plate. The observed thermal image revealed two area of crack in the defective ceramic heating plate.

On the Experimental Modeling of Focal Plane Compensation Device for Image Stabilization of Small Satellite (소형위성 광학탑재체의 영상안정화를 위한 초점면부 보정장치의 실험적 모델링에 관한 연구)

  • Kang, Myoung-Soo;Hwang, Jai-Hyuk;Bae, Jae-Sung;Park, Jean-Ho
    • Journal of the Korean Society for Aeronautical & Space Sciences
    • /
    • v.43 no.8
    • /
    • pp.757-764
    • /
    • 2015
  • Mathematical modeling of focal plane compensation device in the small earth-observation satellite camera has been conducted experimently for compensation of micro-vibration disturbance. The PZT actuators are used as control actuators for compensation device. It is quite difficult to build up mathematical model because of hysteresis characteristic of PZT actuators. Therefore, the compensation device system is assumed as a $2^{nd}$ order linear system and modeled by using MATLAB System Identification Toolbox. It has been found that four linear models of compensation device are needed to meet 10% error in the input frequency range of 0~50Hz. These models describe accurately the dynamics of compensation device in the 4 divided domains of the input frequency range of 0~50Hz, respectively. Micro-vibration disturbance can be compensated by feedback control strategy of switching four models appropriately according to the input frequency.

Bubble Popping Augmented Reality System Using a Vibro-Tactile Haptic Mouse (진동촉각 햅틱 마우스 기반 버블포핑 증강현실 시스템)

  • Jung, Da-Un;Lee, Woo-Keun;Jang, Seong-Eun;Kim, Man-Bae
    • Journal of Broadcast Engineering
    • /
    • v.15 no.6
    • /
    • pp.715-722
    • /
    • 2010
  • As one of applications in augmented realities, this paper presents a bubble popping system utilizing a haptic vibro-tactile mouse. In this system, virtual bubbles randomly float in the 3D space. By using the vibro-tactile mouse grabbed by a user, the bubbles are popped when they are touched by the mouse in the 3D space. Then a bubble popping effect with addition mouse vibration is delivered to the user's hand through the mouse. The proposed system is developed on ARToolkit environment. Therefore, basic components such as a camera and a marker pattern are required. The systems is composed of a vibro-haptic mouse, a webcam, a marker pattern, a graphic bubble object, and graphic mouse. Mouse vibration as well as bubble fade-out effect is delivered. Therefore, the combination of visual and tactile bubble popping effects outperforms the usage of a single effect in the experience of augmented reality.

Identification of frequency determining sound generating organ of cicadas with the Helmholtz resonator structure (헬름홀쯔 공명기 구조 매미 소리의 주파수 결정 발음기관 규명)

  • Yoon, Ki-sang;Cho, Se-hyun;Jung, Yoon-sang;Lee, Dong-hyun
    • The Journal of the Acoustical Society of Korea
    • /
    • v.37 no.5
    • /
    • pp.276-283
    • /
    • 2018
  • The purpose of the study is to identify a sound generating organ that has a major influence on the central frequency of the cicadas with the Helmholtz resonator structure for the first time. The sound of cicadas Cryptotympana atrata and Hyalessa fuscata were recorded and analyzed, then the motion of the tymbals was analyzed with a high-speed camera to compare the relationship between the frequency of sound and the motion of the tymbals. As a result, there was little difference in the frequency distribution of calling song and scream for two species. The tymbals of C. atrata oscillated in three vibration modes, while those of H. fuscata oscillated in one mode. There was no difference in the frequency of both tymbals of both cicadas, and three vibration modes of C. atrata generated sound with different frequency bands. The frequency band of tymbals and the central frequency band of calling song were very similar. In conclusion, it is presumed that the frequency of the cicadas with the Helmholtz resonator structure was determined by mode frequency of the tymbals than resonance condition of the abdomen.

A Study on the Development of Wearable Smart Fashion Product - Focused on the Construction of Optimized Functionalities for Particular Needs - (웨어러블 기능성 스마트 패션제품 개발 연구 - 특정사용자를 위한 특수한 기능성 구현을 중심으로 -)

  • Lee, Hyunseung;Lee, Jaejung
    • Fashion & Textile Research Journal
    • /
    • v.21 no.2
    • /
    • pp.133-140
    • /
    • 2019
  • This study developed smart fashion prototypes that provide utilitarian functionality by combining Fashion and Electronics regarding the IT focused convergence tendency in modern industries. A convergence R&D workshop was performed by Fashion design majors and Engineering majors for the study. As a result, 5 functional smart fashion prototypes were developed and the outline of each prototype are as follows. The $1^{st}$ prototype, 'Hidden Camera Detecting Coat' focused on gender-related crimes. The coat uses infrared lighting and LED technologies to provide a function to detect hidden cameras in suspicious public spaces such as toilets. The $2^{nd}$ prototype, 'Heating-massage Suit' targeted patients with musculoskeletal system difficulties. The suit uses heating and vibration technologies to provide a heating massage treatment for patients with ongoing difficulties in their daily lives. The $3^{rd}$ prototype is an air-bag jacket to prevent sexual molestation on public transportation. The jacket extends its volume through pressure sensing, air compressing, motors and 3D-printing technology to secure the wearer's personal preventive space between the user's body and others. The $4^{th}$ prototype is a town wear for people suffering from synesthesia. People with synesthesia inadvertently see colors when exposed to certain sounds. This town wear uses sound sensing, air compressing, motors and 3D-printing technology to provide sound prevention and a comfortable sound playing function. The $5^{th}$ prototype is a set of a vest and a gloves for visually impaired people. The vest and gloves uses DMS, voice playing, vibration technology to provide distance measuring and warning functions.