• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.9
• /
• pp.72-79
• /
• 1997

The dominant physical process repsonsible for the nonlinear gain is from spectral-hole burning with the time constant fo about 50fs and the contribution to the nonlinea rgain form hot carriers effect is determined to be about 15% of the contribution due to spectral-hole burning. To prove the above results we fit the data of hall and found that hot carriers have a profound effect on their experimental data despite the fact that the magnitude of hot carriers effect is only 15% of spectral-hole burning. We suggest that the experimenta with a pump pulse width of 180 fs is very sensitive in detecting the effect of hot carriers, but is not sensitive in detecting much faster process associated with spectral-hole burning.

• Journal of Korea Foresty Energy
• /
• v.22 no.1
• /
• pp.24-29
• /
• 2003

Using woodceramics made from sawdust board of Larix leptolepis thinning logs, change in surface temperature were investigated, by the rate of resin impregnation and burning temperature. As the surface temperature of silicon rubber heater was going up, that of woodceramics also increase rapidly. Woodceramics made from under the condition of the rate of resin impregnation 70-80% and burning temperature 800-$1000^{\circ}C$, were higher than that of surface temperature. Also, it was found that woodceramics maintained heat for a long time because the descending velocity of their surface temperature was lower than that of the heater.

• Journal of the Korean Society of Safety
• /
• v.8 no.1
• /
• pp.35-46
• /
• 1993

This paper was concerned with the risk assessment about oxidizing substances as dangerous goods by burning test method. The sample. which was formed with the heaped cone-shape. was composed of solid oxidant and sawdust. The burning time of each sample was measured under the following various conditions circumstance temperature. mixing ratio of oxidizing substance and sawdust. particle size of sawdust and kinds of sawdust. As a results. the effective combustibility was gained when the sawdust content was 20∼30 wt.% in the sample and the lauan with -30+50 mesh was used. But. although the circumstance temperature increased. burning efficiency of the samples wet$.$e not affect by it. Finally. the average burning times were obtained by considering the weighting factors related on the mixing ratio and the circumstance temperature. And then. it were compared with the combustion risk level and the effects of cation and anion of oxidizing substances as dangerous goods.

• Journal of the Korean Society of Safety
• /
• v.11 no.3
• /
• pp.137-142
• /
• 1996

Combustion characteristics of immobilized methyl, ethyl and propyl alcohols on sands were studied. Experiments were performed by burning methyl, ethyl and propyl alcohols Immobilized on sands (particle size 0.1~5mm) and ceramic balls(particle size 5mm) to measure mass burning rate, height burning rate and combustion temperature. It was concluded that the longer time from ignition to extinguishment was resulted from the larger particle size of sands and the smaller size of sands exhibited the higher mass burning rate. Of alcohols tested the relative magnitude of facilitation of combustion was methyl>ethyl>propyl alcohol. Combustion temperature of alcohols, without regard to the types of alcohols, was not increased with smaller sands. However, with larger sands, combustion temperatare of alcohols was increased with the larger particle.

• Journal of the Korean Ceramic Society
• /
• v.44 no.9
• /
• pp.517-523
• /
• 2007

For the preparation of tricalciumaluminate $(C_3A)$ clinker, in traditional clinkering method using oxides and carbonates as a raw material, uneconomical repetition of burning have been necessary to avoid the melting of clinker by eutectic reaction in the system $CaO-Al_2O_3$. In this study, special starting raw materials for the clinker burning were prepared from a mixture of oyster shell and aluminium hydroxide by heating to $1100^{\circ}C$ and hydrating at $30^{\circ}C$. The starting raw materials, hardened body with weak hydraulic strength, were mainly composed of $C_3AH_6$ formed by resolution-precipitation mechanism of the system $CaO-Al_2O_3-H_2O$. By heating them, relatively pure $C_3A$ clinker could be obtained by one-time burning at the fairly lower temperature than that of conventional method. The easier formation of $C_3A$ clinker seemed to be caused by higher compositional homogeneity and stoichiometry of the starting materials, high surface area and crystallographic instability of the thermally decomposed products, and the catalytic effect of decomposed moisture on the early-stage crystallization of calciumaluminates. The basic hydration behavior of the clinker was also confirmed.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.1
• /
• pp.41-45
• /
• 2003

In this study, woodceramics were made from MDF with various resin impregnation rate. To investigate the change of surface temperature of woodceramics, the impregnated MDF was burned at the temp. 600, 800, 1,000, 1,200℃. Surface temperature of woodceramics was increased as impregnation rate and burning temperature was increased. The specimen burned at 800℃ was lower than others. Change of temperature under given temperature increased as time passed and it showed more increased in temperature at burning temperature of 1,200℃. Change of surface temperature increased when floor temperature increased and the temperature was 49.2℃ at 70℃ in floor temperature of 1,200℃ specimen. The decent in surface temperature of woodceramics was the fastest decrease at the burning temperature of 800℃ specimen.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.5
• /
• pp.122-134
• /
• 1995

The present study was investigated combustion characteristics of methane-air mixtures at stratified charge in a constant volume combustion chamber. The main results obtained from this study can be summarized as follows. In case of ${\phi}_s=1.0$, total burning times greatly affected rather than initial time of pressure increase and maximum combustion pressure. In case of ${\phi}_t=1.0$, initial time of pressure increase and total burning times were affected considerably in comparison with the case of ${\phi}_s=1.0$. Also, even the very lean mixture which total equivalence ratio is ${\phi}_t=0.69$(${\phi}_s=1.0$, ${\phi}_m=0.65$), by changing configuration of the critical passage-hole and using a stratified mixture, it is possible to decrease substantially the initial time of pressure increase. total burning times and NOx concentration without deteriorating combustion characteristics such as maximum combustion pressure, rate of heat release etc. in comparison with the use of single chamber(in case of ${\phi}=1.0$) only. Specifically, our trends were revealed remarkably in the case of Type D which is reduced a flame contact area of sub-chamber side of the passage-hole.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.8 no.3
• /
• pp.150-156
• /
• 1975

This paper dealt itself with the relation of the heat release rate with crank angle in combustion process by adjusting the injection time, injection amount and engine speed of diesel engine. The result of test were obtained by analyzing indicator diagram of KUBOTA 2LKE diesel engine, where the indicator was used Tertronix oscilloscope. The combustion period of diesel engine is composed of premixed burning time and combustion controlled time. The larger the premixed burning region, the higher efficiency was obtained with the higher maximum pressure than at the time of the normal smooth operation. The longer the combustion controlled time, the lower the maximum pressure than the period of the normal operation, but the efficiency was decreased. The region of premixed burning was principally controlled by injection delay, but combustion controlled time was affected when oxygen and fuel were mixed. Efficiency of engine was increased at the time of earlier injection time under the constant injection amount, and engine speed, but the pressure increasing was observed higher than the efficiency increasing.

• The Korean Journal of Quaternary Research
• /
• v.16 no.2
• /
• pp.1-8
• /
• 2002

In this paper, the writer attempts to clarify causes by general man and weather factor on forest fire occurrence in Kosong-Area, 1995-2001. The major results are summarized as follows: The forest fire at Kojin-ri, Sonyusil-ri and Majwa-ri occurred at the same area over 3 times and that Hakya-ri, Songdae-ri and Inhung-ri, at the adjoining land over 3times. In the total 46 times of forest fire, fire frequence was greatest in March(11 time) and April(11 time) followed by November(7 time), January(6 time), February(6 time). December(3 time), October(2 time). Hours on frequent forest fire are from 11:00 till 18:00. Number for forest fire occurrence by causes was greatest in military training followed by burning paddy fields, debris burning, burning agricultural debris, visiting a grave, cigarette and arson. Frequent forest fire in Kosong-Area coincide not only with above normal temperatures, but also with below normal relative humidity. When the strong winds appear at Kosong-Area, the properties of daily surface chart re the south high and north low pressure pattern in the Far East Asia.

• Journal of the Korean Wood Science and Technology
• /
• v.15 no.3
• /
• pp.56-67
• /
• 1987

Plywoods used for construction as a decorative interior material are inflammable and can make fire accidents, causing destruction of human life and property. Therefore, it is indeed required to make fire-retardant treated plywood. In this study, 3.7mm yellow meranti plywoods were soaked in 18% boric acid solutions and tap water by hot-cold bath for 1/2, 2/2, 4/2, 6/2 hours and redrying of treated plywoods was carried out by press drying at the platen temperature of 110, 130, 160, $180^{\circ}C$ and then it was conducted to investigate solution absorption, drying rates, dynamic young's modulus. specific gravity and fire-retardant factors such as burning point, flame spread length. flame exhausted time, back side carbonized area and weight loss by treating time, treating solutions and platen temperature. The results are as follows; 1. When plywood was impregnated with the hot bath temperature of $70^{\circ}C$ for 1. 2, 4, 6 hours and the cold bath temperature of $15^{\circ}C$ for 2 hours respectively, retentions of boric acid were 1.565, l.597, 1.643, 1.709kg/$(30cm)^3$ and all of them exceeded the minimum retention [1.125kg/$(30cm)^3$] even in the shortest treatment. 2. In hot-cold bath method for 1/2 hours, the drying rates of treated plywood remarkably increased with the extension of platen temperature of 110, 130, 160, $180^{\circ}C$ and the values of boric acid treated plywood were 5.900, 10.196, 45.42, 54.958m.c%/min and the values of water treated plywood were 6.014, 12.373, 46.520, 55.730m.c%/min and drying rates of water treated plywood were faster than those of boric acid treated plywood. 3. The values of boric acid treated plywoods in dynamic young's modulus were widely higher than those of water treated plywoods. And it can be observed that there were highly significant differences for treating time between dynamic young's modulus, and the values of boric acid plywoods increased with the extension of treating time but on the contrary water treated plywoods were decreased values with prolonged time 4. It was observed that there were highly significant differences for platen temperature between dynamic young's modulus. When the values of water treated plywoods in dyna nic young's modulus were abruptly decreased according to the rise of platen temperature. boric acid treated plywoods showed rather increased values at $160^{\circ}C$ of platen temperature. And in 2- way interactions, there were also highly significant for dynamic young's modulus between treating time x treating solutions and platen temperature x treating solutions. 5. Correlation coefficients of fire-retardant factors were shown in table 5. It could be recognized that there were close correlations between the treating solutions and burning point, flame spread length, back side carbonized area, flame exhausted time and weight loss, but there was no correlation between fire-retardant factors and treating time and platen temperature. 6. From table 6, it can be observed that there were highly significant differences for burning point, flame spread length, flame exhausted time, back side carbonized area, weight loss between treating solutions. And in 2-way interactions, there were highly significant for burning point, flame spread length, weight loss between treating time $\times$ treating solutions.