• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.177-177
• /
• 2009

이동통신 시스템의 소형화 경량화 다기능화 추세에 따라 세라믹 모듈의 정밀도 및 집적도가 중요한 요소로 부각되고 있다. 이러한 모듈의 고집적화 추세에 대응하기 위하여 세라믹 소성시 수축율 제어가 필수적인 요소로 부각되고 있으며, 이에 따라 X, Y축의 소성 수축율을 0에 근접하게 제어하는 무수축 소성 기술이 요구되고 있다. 선행연구를 통하여 $Al_2O_3$/Glass/$Al_2O_3$ 구조의 glass infiltration법에 의한 무수축 소성 기술 구현 가능성을 확인하였으나, 아직 해결해야 할 문제점들이 있다. glass가 $Al_2O_3$층으로 infiltration되는 과정에서 glass층이 de-lamination 되는 결함이 발견되었으며 이는 유전체 기판의 Q값을 낮추고 기판의 신뢰성에 악영향을 줄 수 있어 이에 대한 개선이 필요한 실정이다. 본 연구에서는 $Al_2O_3$/Glass/$Al_2O_3$ 구조의 glass infiltration법에 의한 선행 실험에서 관찰된 기판 내부의 de-lamination 현상에 대한 원인을 규명하고 해결책을 제시하고자 하였다. glass 유동과 바인더 burn-out이 동시에 진행됨에 따라 기공이 생성되며 glass가 점성유동함에 따라 이 기공이 glass층으로 모이게 되어 de-lamination 현상이 발생하는 것으로 사료된다. 이를 해결하기 위하여 de-lamination층에 $Al_2O_3$의 tamping을 시도하여 glass층의 기공이 빠져 나갈 수 있는 channel 을 형성하고, 남아있는 기공을 $Al_2O_3$로 채우는 효과를 얻을 수 있었다. 이에 따라 기판의 밀도와 Quality factor 값이 향상되었으며 미세구조가 치밀한 무수축 기판을 제작할 수 있었다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.4
• /
• pp.149-156
• /
• 2006

This paper investigates the steady state combustion characteristics of LPG homogeneous charge compression ignition(HCCI) engine with variable valve timing(VVT) and dimethyl ether(DME) direct injection, to find out the benefits in exhaust gas emissions. VVT is one of the attractive ways to control HCCI engine. Hot internal residual gas which is controlled by VVT device, makes fuel is evaporated easily, and ignition timing is advanced. Regular gasoline and liquefied petroleum gas(LPG) were used as main fuel and dimethyl ether(DME) was used as ignition promoter in this research. Operating range and exhaust emissions were compared LPG HCCI engine with gasoline HCCI engine. Operating range of LPG HCCI engine was wider than that of gasoline HCCI engine. The start of combustion was affected by the intake valve open(IVO) timing and the ${\lambda}TOTAL$ due to the latent heat of vaporization, not like gasoline HCCI engine. At rich operation conditions, the burn duration of the LPG HCCI engine was longer than that of the gasoline HCCI engine. CAD at 20% and 90% of the mass fraction burned were also more retarded than that of the gasoline HCCI engine. And carbon dioxide(CO2) emission of LPG HCCI engine was lower than that of gasoline HCCI engine. However, carbon oxide(CO) and hydro carbon(HC) emission of LPG HCCI engine were higher than that of gasoline HCCI engine.

• Journal of Digital Convergence
• /
• v.10 no.1
• /
• pp.165-175
• /
• 2012

The government, Ministry of Education, Science and Technology(MEST) presented a new policy that standardizes digital textbooks as a method to accept the change of education paradigm in 2006. Since 2007, MEST has begun to provide digital textbooks for some elementary schools. MEST proposes to change digital textbooks as a standard in elementary, middle, and high schools in the future. However, the use of digital textbooks has led to concern about the health of students. The purpose of this study was to identify health-adverse effects of the use of digital textbooks on the health of students. Literature reviews regarding digital textbooks including national and international literature were conducted. The literature reviews found the key physical and psychological factors to be considered in using digital textbooks. The physical factors were symptoms and signs associated with eye, musculoskeletal system, general health, and skin. The mental factors were 'burn out of study' and 'stress due to study'.

• Fire Science and Engineering
• /
• v.30 no.2
• /
• pp.114-122
• /
• 2016

This study is to analyze the explosion and fire risks due to high temperature and short circuit current of Lithium batteries. This study selected the typical types of Li-polymer batteries and Li-ion batteries as the test samples. The result of explosion risk assessment due to the high temperature showed that, while a Li-polymer battery had $170^{\circ}C$ explosion on average, a Li-ion battery had $187^{\circ}C$ explosion. The measurement result of temperature increase due to short circuit current revealed that, in case that protection circuit module (PCM) was normally working, there was little of temperature increase due to over-current limitation. However, in case that PCM was out of order, the temperature of a Li-polymer battery increased up to an average of $115.7^{\circ}C$ and the temperature of a Li-ion battery increased up to an average of $80.5^{\circ}C$, which showed the higher risks of fire and burn.

• Journal of Acupuncture Research
• /
• v.28 no.2
• /
• pp.1-11
• /
• 2011

Objectives : The aim is to comprehend the difference of moxibustion used according to applied body parts (knee pain, neck pain, back pain) to oriental doctors running clinic in Seoul. Methods : A sampling of 288 oriental doctors running clinic in Seoul was done and the doctors were asked to fill out 20 questions by interviewing directly from Nov. 23. 2009 to Jan. 9. 2010. Results : The result shows that moxibustion was used for knee pain and back pain more than neck pain. The type of moxibustion mostly used was sticker moxibustion for all three symptoms. Burn marks were left mostly in knee and back pain. Most large volume of moxa was used to back pain. More than half of the oriental doctors used 1-3 acupoints for one procedure and on average 2-3 sessions was done. Patients with knee pain and back pain had more than 4 sessions compared to neck pain. Treatments were mostly done 3 times a week, and as for total treatment period, it took less than 1 week for acute symptom, and it took more than 1 week and less than 5 weeks for chronic symptom. Conclusions : This research shows that the method of moxibustion used differs according to the area of treatment(knee pain, neck pain, back pain) by survey of oriental doctors through direct interviews.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.2
• /
• pp.420-425
• /
• 2010

In the process of warm forging, billet is heated up to $800^{\circ}C$ and located in the upper part of die block impression. The scattered oxidized scale may cause workers burn and shortening of die life sticking to the die block impression. The separating materials sprayed in die block cause harmful dust, harmful mist, fume, and bad odor which contaminate workshop environment. The process is classified as one of the avoided jobs and make the planned output achievement difficult. Development of an elimination device to clear out the contaminating materials in the workshop and improvement of the unsatisfactory maintenance method to fix the abrasion of die block impression which delays the dead line, cost increases needs to be developed. In this research, I tried to solve the problems caused in warm forging of bronze pipe joint such as the billet heating process, die maintenance, and manufacturing cost through improvement of warming forging manufacturing method and die maintenance method and eliminating harmful gas which will make the workshop more environment friendly.

• Journal of Korean Physical Therapy Science
• /
• v.22 no.1
• /
• pp.29-36
• /
• 2015

Purpose : The purpose of present study was to improve communication of pain expressing terms and pain intensity between patient and physical therapist, and initiated to objectify a measurement of subjective pain. Methods : Data were delivered to 249 people by a self-completion questionnaire, and analyzed 160 copies except for 87 mark error of the collected 247 questionnaires. The questionnaire included a question on 55 terms used to describe pain, the type of the pain, and pain intensity using VAS (visual analogue scale). Results : The results were as follows; 'Tight' was the most frequently being expressed term of muscular pain, subsequently to 'knot' and 'dull'. 'Tear' was the term representing the most strong pain of muscular pain, subsequently to 'rupture' and 'squeeze'. 'Stinging' was the most frequently being expressed term of neurologic pain, subsequently to 'get shocked' and 'wriggle'. 'Burn' was the term representing the most strong pain of neurologic pain, subsequently to 'sear' and 'get shocked'. 'Creak' was the most frequently being expressed term of joint pain, subsequently to 'peel' and 'out of joint'. 'Break' was the term representing the most strong pain of joint pain, subsequently to 'peel' and 'crack'. Conclusion : The objectification of pain terms will be used to help physical therapist to check the patient's pain.

• Journal of the Korean association of regional geographers
• /
• v.15 no.2
• /
• pp.204-214
• /
• 2009

The purpose of this paper is to elucidate the formation processes of Hwaeumneup in Cheonseong Mountain which was designated as Wetland Conservation Area in 2002, and to offer data essential to sustainable management of wetland. According to wetland core samples and carbon dating of humus, grassland of Hwaeumneup Wetland Reservation resulted from slash-and-burn agriculture in no reference with climatic changes of last glacial period. And Hwaeumneup is a alpine wetland that is formed as rain water over Cheonseong Mountain crest area infiltrates into bedrock, springs out along joint line below main ridge, and dampens gentle grassland. It needs to support dense vegetation of southwestern ridge of Wetland Reservation in order to sustain water volumn of Hwaeumneup wetland, and to keep from breakdown of block dam at downstream fringe of wetland. And it needs to measure and analyse micro-topography and hydrology changes in Hwaeumneup Wetland Reservation through periodic monitoring.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.187-192
• /
• 2002

Applicability of laser micro welding process to the fabrication of medical devices was investigated. Austenitic stainless steel wire (SUS304) was spot melted and crosswise welded, which is one of the most possible welding process for the fabrication of medical devices, by using a Nd-YAG laser. Effects of welding parameters on the microstructure, tensile strength and corrosion resistance were discussed. In the spot melting, melted metal width decreased with decreasing the input energy and pulse duration. Controlling the laser wave to reduce laser noise which occurred in the early stage of laser irradiation made reasonable welding condition wider in the welding condition of small pulse duration such as 2ms. The microstructure of the melted metal was a cellular dendrite structure and the cell size of the weld metal was about 0.5~3.5 ${\mu}{\textrm}{m}$. Tensile strength increased with the decrease of the melted metal width and reached to a maximum about 660MPa, which is comparable with that for the tempered base metal. Even by immersion test at 318K for 3600ks in quasi biological environment (0.9% NaCl), microstructure of the melted metal and tensile strength hardly changed from those for as melted material. In the crosswise welding, joints morphologies were classified into 3 types by the melting state of lower wire. Fracture load increased with input energy and melted area of lower wire, and reached to a maximum about 80N. However, when input energy was further increased and lower wire was fully melted, fracture load decreased due to the burn out of weld metal.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.17 no.2
• /
• pp.41-46
• /
• 1989

Rhododendron micranthum grown over the area of Kyoung Puck, Kang Weon Province is showy and very attractive evergreen broad-leaned shrub of shade resistance. This shrub is considered very useful for exploiting as a garden plant. Environments, growth characteristics and vegetation association in the wild habitat and in the garden planted with this shrub, were investigated to find out some appropriate means of propagation and cultivation of this shrub. The results thus obtained were stated as follows ; 1. Light intensity for the native habitat ranged in the proximity of 9%. The most abundant stand of this shrub occurred in the northen side of mountains, while still some plants were found in the eastern sides also. 2. Soil of the native habitat was acidic (pH 4.4) and infertility. 3. Average elevation of the native habitat was shown to be 230m above the sea level. 4. The plant of the native habitat showed an average of 3.9 new shoots per branch, whereas that of the garden planted (light intensity 100%) showed 1.2, 5% of an average was for sun-burn leaves were noted, while garden Plants(light intensity 100%) showed 90% of them. 5. Other tree species associated with Rhododendron micrathum in the native habitat were primarily Pinus densiflora and secondarily Sorbus alnifolia, hemerocallis aurautiaca, Rubus crataegifolius, and Salix hulteni. 6. Vegetation rate of plant habitats in the Rhododendron growing area was observed to be 0 to 80% involving 27 to 50 species of associated trees in the vegetation for the 10${\times}$10m quadrat area.