• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.1
• /
• pp.156-162
• /
• 2015

This paper has analyzed how conduction path and electron concentration for the device parameters such as oxide thickness, channel doping, and top and bottom gate voltage influence on subthreshold swing of asymmetric double gate MOSFET. Compared with symmetric and asymmetric double gate MOSFET, asymmetric double gate MOSFET has the advantage that the factors to be able to control the short channel effects increase since top and bottom gate oxide thickness and voltages can be set differently. Therefore the conduction path and electron concentration for top and bottom gate oxide thickness and voltages are investigated, and it is found the optimum conditions that the degradation of subthreshold swing, severe short channel effects, can reduce. To obtain the analytical subthreshold swing, the analytical potential distribution is derived from Possion's equation. As a result, conduction path and electron concentration are greatly changed for device parameters, and subthreshold swing is influenced by conduction path and electron concentration of top and bottom.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.4
• /
• pp.281-285
• /
• 2020

Oxide semiconductor devices have become increasingly important because of their high mobility and good uniformity. The channel length of oxide semiconductor thin film transistors (TFTs) also shrinks as the display resolution increases. It is well known that reducing the channel length of a TFT is detrimental to the current saturation because of drain-induced barrier lowering, as well as the movement of the pinch-off point. In an organic light-emitting diode (OLED), the lack of current saturation in the driving TFT creates a major problem in the control of OLED current. To obtain improved current saturation in short channels, we fabricated indium gallium zinc oxide (IGZO) TFTs with single gate and double gate structures, and evaluated the electrical characteristics of both devices. For the double gate structure, we connected the bottom gate electrode to the source electrode, so that the electric potential of the bottom gate was fixed to that of the source. We denote the double gate structure with the bottom gate fixed at the source potential as the BGFP (bottom gate with fixed potential) structure. For the BGFP TFT, the current saturation, as determined by the output characteristics, is better than that of the conventional single gate TFT. This is because the change in the source side potential barrier by the drain field has been suppressed.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.3
• /
• pp.202-209
• /
• 2019

The objective of this study is to examine the reproducibility for compressive strength development and mechanical properties of lightweight concrete made using bottom ash aggregates and foam(LWC-BF). Based on the mix proportions conducted by Ji et al., six identical mixes were prepared with different actual foam volume ratios from 0% to 25% and water-to-binder ratios from 25% to 30%. The presently measured properties, including initial slump, slurry density, compressive strength gains at different ages, splitting tensile strength, and modulus of rupture, were very close to those determined in the previous tests by Ji et al. Thus, the developed LWC-BF has a good potential in obtaining a reproducibility for compressive strength development and mechanical properties even though the troubles of mixing control owing to the addition of preformed foam.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.371-371
• /
• 2000

A strategy for the swing-up control according to states of the 2-link rotational pendulum is proposed. The proposed controller consists of two modes of control such as divergence mode and stabilization mode. When the controller is in divergence mode, control input is generated using sinusoidal and signum function to make the first and second links reach the bottom and top positions, respectively. After the controller finishes divergence mode, stabilization mode is initiated to keep the pendulum around the top position using pole-placement method. Dynamic models including actuator dynamics are obtained using coordinate changes at each control mode. Simulation results are given to show the effectiveness of the proposed method.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.305-308
• /
• 2004

The constant flow control valve is used to control the flow rate of heating water in the large apartment complex and buildings. It is important to have similar heating flow rate in the apartments, even though the apartment is top or bottom floors. To achieve those purposes, the constant flow control valve was developed. The performance of this control valve is effected by hole area and discharge coefficients of the cartridge holes. The discharge coefficients of orifice hole in the cartridge were testes with various sizes of holes and various flow direction in the holes. The discharge coefficients decreased as the hole size increased due to the collision at the cartridge wall of water jet. The effects of the flow direction at the hole were not significant on the discharge coefficients.

• Structural Engineering and Mechanics
• /
• v.12 no.2
• /
• pp.157-168
• /
• 2001

In this paper, experimental investigation into the behavior of reinforced concrete (RC) columns tested under large lateral displacement with four different types of loading arrangements is presented. Each loading arrangement has a different system for controlling the consistency of the loading condition. One of the loading arrangements used three units of link mechanism to control the parallelism of the top and bottom stub of column during testing, and the remaining employed eight hydraulic jacks for the same purpose. The loading systems condition used in this investigation were similar to the actual case in a moment-resisting frame where the tested column was displaced in a double curvature. Ten model column specimens, divided into four series were prepared. Two columns were tested monotonically until collapse, and unless failure took place at an earlier stage of loading, the remaining eight columns were tested under cyclic loading. Test results indicated that the proposed system to keep the top and bottom stubs parallel during testing performed well.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1428-1431
• /
• 1997

This paper presents an efficient fault diagnosis methodology for lare chemical processes. The methodology is based on a two-tier strategy, When a falt occurs in a process, a top tier identifies the sector (process part or unit) that may contain the fault(s). Afterwards, a bottom tier or lower level evaluates the suspicious sector. The process modeling methodology based on functionality-behavior relations of process units, is proposed and utilized in the top-tier. This methodology models a target process as sequences of functions and variables and their relations. In the bottom tier, each sector has a dedicated diagostic module, which is tailored to the available information or models of the sector. For the sectors selected in the top-tier diagnosis, each diagnostic module is executed to identify the actual faults within the sector. Teh utility of the methodology is illustrated in the diagnosis of the CSTR with heat exchanger.

• ETRI Journal
• /
• v.40 no.3
• /
• pp.389-395
• /
• 2018

A novel class of planar metamaterial unit-cells consisting of a peace logo pattern is presented. A significant advantage of the proposed peace-logo planar metamaterial (PLPM) unit-cell over existing designs is its tunability, simplicity, and compatibility with microstrip structures. The theoretical analysis is founded on the famous transmission-line theory for the metamaterial concept. Then, the tunable dual-band two-sided PLPM (TSPLPM) unit-cell is designed by printing a similar PLPM pattern at the bottom of the substrate. The influence of the bottom PLPM pattern on the resonance frequencies of the unit-cell was analyzed by performing numerical simulations using CST Microwave Studio 2017 and HFSSv15 simulators. The results of the numerical simulations demonstrated that the proposed TSPLPM has the ability to control the resonance frequencies over 50 GHz-75 GHz for millimeter-wave applications.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.5
• /
• pp.674-682
• /
• 2012

A new intelligent stereo vision sensor system was studied for the motion and depth control of unmanned vehicles. A new bottom-up saliency map model for the human-like active stereo vision system based on biological visual process was developed to select a target object. If the left and right cameras successfully find the same target object, the implemented active vision system with two cameras focuses on a landmark and can detect the depth and the direction information. By using this information, the unmanned vehicle can approach to the target autonomously. A number of tests for the proposed bottom-up saliency map were performed, and their results were presented.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.558-563
• /
• 2003

The tracked vehicle travel on off rod and on rod. So the tracked vehicle need a sufficient stiffness and a lightweight. In this study we performed FEA for the track vehicle and performed topology optimization based on the results of FEA. The displacements of road wheel are used as displacement constraint for topology optimization. We performed topology optimization with the control of the frame size which is the results of topology optimization and suggested the shaped of the tracked vehicle bottom plate of topology optimization