• Journal of the Korean Home Economics Association
• /
• v.25 no.1
• /
• pp.43-50
• /
• 1987

Non-durable flame retardant finish, borax/boric acid mixed solution, was applied to cotton fabric with pad-dry method. The LOI(limited oxygen index) was measured as the measare of the flame retardant effect. The TGA was investigated to know the thermal behavior of the samples. In addition, the solubility of the solutions was investigated. The results were as follows: 1) There was a synergism of flame retardant effect in the borax/boric acid mixed solution treatment and the maximum synergism was shown around the ratio of 7 : 3 2) After the borax/boric acid solution treatment, the degradation temperature was lowered and degraded at the larger temp range with slower rate. The residual char length also increased. 3) The solubility of borax/boric acid become higher when the ratio of borax/boric acid became similar. Compositions from 80/20 to 40/60 borax/boric acid mixtures were solubilized well in room temperatuare or warmwater therefor there was no problem for home use.

• Journal of the Korean Society of Safety
• /
• v.6 no.1
• /
• pp.14-25
• /
• 1991

The smouldering combustibility of cellulose insulation treated with boric acid-borax-alum as combustion retardants are examined by cigarette ignition method and electrical cardrige heater method. The alum to be required at an add on level of at least 12% by weight of cellulose treated with boric acid-borax-alum=2 ： 1 ： 2 fomulatlon if resistance to smouldering combustion by cigarette ignition is to be achived. The optimum electrical ignition source employed by electrical cartidge heater method was 23.2 watts(80V) power level The effectiveness of Alum as a third combstion retardant are acceptable both smouldering resistance and flame resistance at 18% level of all examined formulation.

• Journal of the Korean Society of Safety
• /
• v.7 no.4
• /
• pp.7-12
• /
• 1992

The smouldering combustibility of cellulose insulation treated with boric acid-borax-aluminium sulfate as combustion retardants are examined by cigarette ignition method and electrical cardrige heater method. The effectiveness of Aluminium sulfate as a third combustion are acceptable both smouldering resistance and flame resistance at 18% level of all examined formulation. As the proportion of Aluminium sulfate in the formulation was increased, the flame resistance of cellulose insulation was improved.

• Journal of the Korean Wood Science and Technology
• /
• v.49 no.6
• /
• pp.602-615
• /
• 2021

Red jabon wood is a potential fast-growing species for veneer, furniture, and many other wood products, but its durability is very low. The purpose of this study was to investigate the effects of castor bean oil and heating on boron leaching, dimensional stability, and resistance to decay fungi in treated jabon wood. Red jabon wood was preserved with boron solutions containing 5% boron (boric acid, borax, or borax-boric acid). Following that, castor bean oil impregnation and heating were used as posttreatments. Furthermore, all the wood samples were tested in terms of leaching, dimensional stability, and resistance against Schizophyllum commune and Fomitopsis palustris fungi. This study discovered that boron compounds, castor bean oil, and heating treatments influenced the leaching, dimensional stability, and resistance of red jabon wood to decay fungi. The double impregnation of boric acid or borax and castor bean oil, followed by heating at 160℃, significantly reduced water absorption and leaching while increasing the dimensional stability and resistance of red jabon wood against the two tested decay fungi.

• Journal of the Korean Wood Science and Technology
• /
• v.51 no.1
• /
• pp.49-57
• /
• 2023

This research aimed to evaluate the durability of Samama (Anthocephalus macrophyllus) wood treated with boron preservatives, citric acid (CA), and heating against termites. Wood samples were impregnated firstly with 5% boron solutions, such as boric acid, borax and boric acid + borax combination at 1:1 (w/w). The second impregnation used 5% CA. The impregnations were conducted in a pressure tank at 7 kg/cm² for 4 hours. After impregnation, the samples were heat treated at 80℃ or 160℃. All the treated and control samples were exposed to decay fungi, drywood termites and subterranean termites based on SNI 7207:2014 standard. The results showed that boron preservatives reduced fungal attacks on Samama wood. The combination treatment of boric acid, CA and heat treatment at 160℃ was also effective to increase the resistance of Samama wood against white- and brown rot fungi, and drywood termites. Heat treatment consistently improved the resistance of Samama wood from decay fungi.

• Journal of the Korean Wood Science and Technology
• /
• v.9 no.4
• /
• pp.1-21
• /
• 1981

Exterior grades of Douglas-fir and aspen plywood were impregnated with interior fire-retardant chemicals and redried under low-, intermediate-, and high-temperature drying conditions. Fire-retardant treatments included borax-boric acid, chromated zinc chloride, minalith, pyresote, and a commercial formulation. Drying processes included kiln and press-drying. Evaluated were drying rates and defects generated. The borax-boric acid and the commercial treatments redried at rates similar to water-treated controls. Other salt treatments were significantly slower drying and more defect prone. Chromated zinc chloride treatment was consistently the slowest drying and most defect prone. Press drying was three times faster at an equivalent temperature level. However, thickness shrinkage doubled because of 50 1b/in. platen pressure.

• Journal of the Korea Furniture Society
• /
• v.19 no.6
• /
• pp.475-486
• /
• 2008

In this study, fire-retardant chemicals were melt with mixed composition ratios of dibasic ammonium phosphate and each half of boric acid and borax in hot water, in which hammer-milled chips were immersed to increase swelling of waste particleboards. Also, fire-retardant treated particles from sawn lumber chip and recycled particleboard chip were composed in ratio of 70:30 in core layer to improve boards' properties. Retention ratio of fire-retardant chemicals for the particles for face layer was high due to high specific surface area, and that of sawn lumber chips was somewhat higher than that of recycled particleboard chips. The mixture of particles from sawn lumber chips and recycled PB of 70:30 in weight ratio exceeded bending strength of 100 $kgf/cm^2$. It seemed that the relatively greater portions of dibasic ammonium phosphate affected adversely to dimensional stability, however fire-retardants treatment resulted in distinct effect lowering formaldehyde emission such as $E_0$ type(0.5mg/$\ell$ or less) in KS F 3104. In fire-retardancy, the recycled boards with a mixed ratio of dibasic ammonium phosphate to boric acid borax(50:50 mixture) of 70% to 30% in weight satisfied fire-retardancy 3rd grade in KS F 2271, and also this composition from cone calorimeter test met same standard grade figuring total heat release of 4.6MJ/$m^2$.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.3
• /
• pp.315-325
• /
• 2020

Boron compound had many advantages as wood preservative, but it was prone to leaching. Improving boron preservation was required to extend the service life of fast growing and low durability red jabon (Antochephalus macrophyllus) hardwood. This study aimed to evaluate the dimensional stability, color change and durability of modified red jabon wood by double impregnation with boron and methyl methacrylate (MMA) and heat treatment. Impregnation I used boric acid or borax, and impregnation II used MMA, while heat treatment used temperatures of 90 ℃ or 180 ℃ for 4 hours. The dimensional stability, leachability, water absorption, color change and decay resistance of modified red jabon wood were tested. The results showed that MMA impregnation increased the dimensional stability of red jabon wood, while the leaching and water absorption in the wood significantly reduced. Heating at 180 ℃ caused less water absorption and higher dimensional stability of the wood than that of heating at 90 ℃. Impregnation with boric acid and MMA followed by heating at 90 ℃ resulted in the highest wood ASE, 89.9%. The color change (∆E^*) of wood increased significantly after MMA impregnation and heating at 180 ℃. Boric acid impregnation caused more resistant wood than borax impregnation against decay fungi and termites. Impregnation with boric acid and MMA followed with heating at 180 ℃ increased significantly the wood resistance against decay fungi and termites.

• Fire Science and Engineering
• /
• v.29 no.6
• /
• pp.1-5
• /
• 2015

In this study, the combustion characteristics of Hinoki Cypress Louver were measured after performing pressure impregnation with aqueous solution of boric acid, borax, and ammonium phosphate. The characteristics measured include ignition time, critical heat flux, and mass loss rate by incident hear flux (25, 30 and $50kW/m^2$). The samples used for the test were $100{\times}100{\times}10mm$, and the 5 min variation for each incident heat flux was measured 3 times. The results show that the ignition time for incident heat flux of $25kW/m^2$ showed a delay effect of 17.4 to 21.3% except for Type C-H. There was no significant difference at 35 and $50kW/m^2$ in the average mass loss rate in Types A-H and D-H, which had lower rates than Type N-H, which was predicted to be higher than that of Type N-H ($10.7kW/m^2$) by 38.22 to 60.46%. It is thus expected that at the time of initial primary fire, there would be a delay effect against fire spread.

• Journal of Korean Society of Forest Science
• /
• v.78 no.4
• /
• pp.419-424
• /
• 1989

To obtain relative effectiveness in fire resistance among fire retardant chemicals, oxygen indices were determined for 3.5 mm thick, three-ply, meranti plywoods, treated with 5 commercial chemicals and water and then press-dried, through Up and Down method following oxygen index test of ASTM D 2863-77. The oxygen indices obtained were 28.4 for ammonium sulfate, 26.9 for monoammonium phosphate, 43.4 for diammonium phosphate, 30.1 for borax-boric acid, 32.4 for minalith, and 25.5 for water. Therefore, diammonium phosphate was found to rank first in fire-retardant effectiveness, followed by minalith, borax-boric acid, ammonium sulfate, and monoammonium phosphate in turn, judging from the fact that highly flammable materials are likely to have a low oxygen index.