• Horticultural Science & Technology
• /
• v.29 no.3
• /
• pp.201-210
• /
• 2011

This experiment was conducted to investigate physical and chemical characteristics by volume fractions of root media using peatmoss, perlite, and vermiculite, along with effects on the growth of pot chrysanthemums (Dendranthema ${\times}$ grandiflorum 'Vemini') in a C-channel mat irrigation system. To evaluate the physico-chemical properties of 20 root media, the bulk density, particle density, total pore space, pore space, ash content, organic matter, pH, and electrical conductivity were measured and data were analyzed using principal component analysis (PCA). PCA scores revealed that physico-chemical properties changed by the blending of peatmoss, perlite, and vermiculite. The 20 root media were divided into three main groups by hierarchical cluster analysis. At the end of the experiment, the pH and EC of the root media were measured from media divided into four layers. The pH of root media without plants showed a strong linear relationship and the pH of root media with plants increased exponentially. The change of EC in the root medium was indicated as a hyperbolic curve. Plant growth characteristics according to growth in the 20 root media were analyzed by PCA. It was found that the mixing ratios of the root media affected plant growth characteristics. Therefore, mixing ratio is an important factor for pot-plant production in a subirrigation system.

• Tribology and Lubricants
• /
• v.34 no.4
• /
• pp.160-167
• /
• 2018

Vegetable oils can contribute to the goal of energy independence and security owing to their naturally renewable resources. One of the representative vegetable oils is biodiesel, which is being used in domestic and European markets as a blended fuel with automotive diesel. Vegetable oils are promising candidates as base fluids to replace petroleum lubricants because of their excellent lubricity and biodegradability. We prepared biodiesel with a purity of 99.9% via the esterification of waste cooking oil. Blended biodiesel and Petro-lube base oil were mixed to produce five types of mixed lubricating oil. We analyzed the various characteristics of the blended biodiesel with Petro-lube base oil for different blending ratios. The lubricity of the vegetable lubricant improves as the content of biodiesel increases. In addition, since zinc dialkyldithiophosphates (ZnDTPs) are widely used as multifunctional additives in petroleum-based lubricants, we optimized the blending ratio for lubricity, oxidation stability, and shear stability by adding ZnDTP as a performance additive to improve the biodiesel properties, such as oxidation stability and hydrolysis. The optimized lubricants improve by approximately 25% in lubricity and by 20 times in oxidation stability and shear stability after the addition of ZnDTP.

• Journal of the Korean Society of Combustion
• /
• v.18 no.4
• /
• pp.12-20
• /
• 2013

The ignition delay time is an important factor to understand the combustion characteristics of internal combustion engine. In this study, ignition delay times of cool and thermal flame were observed separately in homogeneous charge compression ignition(HCCI) engine. This study presents numerical investigation of ignition delay time of n-heptane and alcohol(ethanol and n-butanol) binary fuel. The $O_2$ concentration in the mixture was set 9-10% to simulate high exhaust gas recirculation(EGR) rate condition. The numerical study on the ignition delay time was performed using CHEMKIN codes with various blending ratios and EGR rates. The results revealed that the ignition delay time increased with increasing the alcohol fraction in the mixture due to a decrease of oxidation of n-heptane at the low temperature. From the numerical analysis, ethanol needed more radical and higher temperature than n-butanol for oxidation. In addition, thermal ignition delay time is sharply increasing with decreasing $O_2$ fraction, but cool flame ignition delay time changes negligibly for both binary fuels. Also, in high temperature regime, the ignition delay time showed similar tendency with both blends regardless of blending ratio and EGR rate.

• Elastomers and Composites
• /
• v.31 no.2
• /
• pp.111-121
• /
• 1996

The characteristic of silicone rubber can be seen from its resistance to both low and high temperature, whereas HNBR is resistant only in high temperature moderatly although it can be compounded to give good tensile properties, good oil resistance while silicone rubber severely lacks in these qualities. This study was initiated a balance of properties by blending HNBR and silicone rubber which is not considered for commercial blending; blends of HNBR with silicone rubber tend to show immiscible due to dissimilar nature of silicone and HNBR, the possibility of phase separation cannot be ruled out, in unfilled system after vulcanisation leading to premature failure. Attempt has been made to improve compatibility and minimise the layer seperation by the use of compatibilizer. Both filled and unfilled systems, in presence and absence of compatibilizer have been studied. Improvement in tensile properties of the blends or are observed as compared to the non-blended rubber. Different ratios of HNBR and silicone rubber are represented in this study. Blends of HNBR with silicone rubber were immiscible system. The tensile strength increased with filler loading.

• Elastomers and Composites
• /
• v.45 no.4
• /
• pp.280-285
• /
• 2010

The CIIR blends with SBR, NBR and BR were prepared with various mixing ratios. The mechanical and physical properties of these blends, such as frictional coefficient, abrasion resistance, compression set, and specific gravity, were measured. In the permanent compression set measurement, the blends at the composition of 75 wt% CIIR showed the highest value, which means the lowest resistance to deformation. As SBR, NBR and BR blends with CIIR, the coefficient of friction of the mixtures showed a tendency to decrease in arithmetic average. In the case of blending CIIR with BR in order to increase the friction force, the negative effect due to reduction in abrasion resistance was greater than the positive effect of the improvement of the traction force caused by increasing friction coefficient.

• Textile Coloration and Finishing
• /
• v.32 no.2
• /
• pp.111-120
• /
• 2020

In this study, lignin/chlorinated poly(vinyl chloride)(CPVC) blended fibers have been produced for the development of low-cost carbon fiber. Carbon fiber manufacturing was accomplished through stabilization and carbonization process. The lignin/CPVC blended fibers were prepared by wet spinning method. Dimethylacetamid e(DMAc) and cychlohexanone in a ratio of 5:1(wt%) was employed as co-solvent. The ratio of lignin/CPVC was prepared at 0/10, 1/9, 2/8, 3/7, 4/6, and 5/5(wt%). The spinning solution was extruded at a rate of 0.1 to 0.4ml/min according to the blending ratio. The speed of the rollers was the same for all ratios(draw ratio=1). Analysis of fiber cross-section by scanning eletron microscopy(SEM) showed that as the lignin ratio increased in the same coagulation bath and distilled water, the pore size of the spinning fiber decreased. Therefore, the highest tensile strength of the blending fibers was 6.3±1.2MPa at the 5/5 ratio. The carbon fiber also showed the best tensile strength of 120.78±2.43MPa at 5/5 ratio.

• Journal of the Korea Institute of Building Construction
• /
• v.19 no.5
• /
• pp.449-456
• /
• 2019

Recent developments in architectural technologies and programs have enabled architects to think creatively and design free-form architecture. however, there are many problems in the production technology of FCP(Free-Form Concrete Panel). In particular, reduced accuracy due to lack of free-form panel production technology can lead to redesign of buildings as a result, problems such as an increase in construction cost and period. Therefore, this experiment aimed to compensate the decrease of the accuracy according to the displacement difference and to derive the proper mixing ratio for maintaining the shape during the free-form panel curing. In this study, molds were made using paraffin that is a recyclable phase change material. Concrete Panel is usually produced from Portland cement, dead burn magnesia, phosphate, borax and fine aggregate. In this study, four mixing ratios of FCP were selected after each material was blended to determine the proper blending ratio of the fluidity phase, the water absorption rate and the water content of the test piece. FCP was fabricated on the basis of the selected four compounding ratios and thickness and error rate were measured. Based on the error rate of the measured FCP, the quality standard was satisfied among the four compounding ratios.

• The Korea Journal of Herbology
• /
• v.35 no.3
• /
• pp.33-45
• /
• 2020

Objective : The present study aimed to evaluate the change of the content of 7 active components in decoctions produced by various proportional pairs of Coptis chinensis Franch and Scutellaria baicalensis Georgi in 'Mixed decoction (MD)' and 'Single decoction mixture (SDM)'. Methods : The samples of MDs were prepared by decocting C. chinensis : S. baicalensis with the ratios of 10 g:10 g, 10 g:20 g, and 20 g:10 g. Those of SDMs were prepared by blending each single decoction from C. chinensis and S. Baicalensis with the ratios of 1:1, 1:2, and 2:1. The samples were evaluated by high-performance liquid chromatography with statistical analyses. Results : The analytical methods, which were optimized and validated, were reliably applied to present research. The content of all components in both MDs and SDMs at C. chinensis : S. baicalensis = 1:1 ratio were reduced compared with single herb decoction. The components from each compositional herb in MDs were proportionally increased with the ratio of original herb increased, but inversely proportional to paired herb. The contents of components in MDs were significantly lower than those in SDMs at all ratios, except for high content of baicalin at C. chinensis : S. baicalensis = 2:1. Conclusion : It was concluded that MDs and SDMs as well as the proportions of herbs could affect the contents of the components from original herbal medicines. These results provide the information for the quality control of herbal medicine combined C. chinensis with S. baicalensis.

• Environmental Engineering Research
• /
• v.23 no.2
• /
• pp.121-128
• /
• 2018

This paper describes the non-isothermal pyrolysis of cashew shell cake (CSC) - bituminous coal blends. The blends exhibit two distinct stages in the thermogravimetric curves, which the first stage stems from CSC and the second one from the superposition of CSC and coal pyrolysis. The pyrolysis behavior of the blend was linearly proportional to the blending ratios. The overall behavior of the blends was evaluated in terms of the maximum rate of weight loss, characteristic temperatures, char yields, and the calculated and experimental thermogravimetric curves. The activation energies ranged up to 49 kJ/mol for the blends were obtained and used to evaluate the interaction in the blends. The present thermogravimetric study shows that there is no significant interaction between CSC and coal in the blends, and it was supported by the characteristic values which are linearly proportional to the weight percentages of cashew cake-shell in the blends. The no-interaction might be due to the fact that the main reaction zones are distinctively different for two constituents, so the additive rule is acceptable for describing pyrolysis behavior of the present blends.

• Journal of the Korean Ceramic Society
• /
• v.27 no.7
• /
• pp.833-840
• /
• 1990

For the development of multi-functional materials which has water reducing power, air entraining power and waterproofing power as well as blending additive in cement mortar the coal ash was modified with asphalt-stearic acid or asphalt-boiled oil mixtures by mechanical treatment. And the physical properties of cement mortar blended with modified coal ashes were compared with those of the water-tightness-cement mortar and the ordinary-portland-cement mortar added with AE.water reducing agent. The mortar of coalash-blend-cement modified with asphalt-stearic mixture was increased acid about 20% in initial strengths and decreased about 20% in water absorption ratio than those of ordinary coalash-blend-cement. The mortar of coalash-blend-cement modified with asphalt-bolied oil mixture was similar to the cement mortar added with AE.water reducing agent in water reduction ratio, air entraining conents and the initial strengths, also was similar to the water-tightness-cement mortar in water absorption and water permeability ratios.