• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.4
• /
• pp.619-627
• /
• 2000

Biodegradation of the C. I. Reactive Blue 114 was investigated in an upflow anaerobic sludge blanket (UASB) reactor. Important parameters studied include dye concentration, the kind and concentration of carbon source, hydraulic retention time (HRT), and influent pH. Glucose was found to be a better co-substrate than the mixture of volatile fatty acids (VFAs), although its concentration did not affect dye removal efficiency in the range of $1000{\sim}3000mg/{\ell}$. When HRT increased from 6 hr to 24 hr, dye removal efficiency increased up to 12 hr and remained almost constant thereafter at about 40%. When influent pH was varied in the range of 6.0~8.0, the effluent pH was varied in the range of 6.8~7.5 with maximum efficiency at pH 7.0. The highest dye removal rate obtained was $52mg/{\ell}{\cdot}day$, while the maximum dye load to meet the discharge limit of color intensity was estimated to be $46mg/{\ell}{\cdot}day$ at HRT of 12 hr and an influent glucose concentration of $2200mg/{\ell}$.

• Journal of Arbitration Studies
• /
• v.28 no.2
• /
• pp.217-248
• /
• 2018

This paper reviews the Supreme Court of Japan in Decision of December 12, 2017, 2016 (Kyo) 43 (2011) concerning arbitrator's duty of disclosure and reasonable investigation under the Japan Arbitration Act (Arbitration Act). The Supreme Court of Japan recently issued a precedential decision interpreting, for the first time, the arbitrator disclosure requirements of the Arbitration Act. Under Article 18(4) of the Arbitration Act, arbitrators have an ongoing obligation to disclose circumstances which may give rise to justifiable doubts as to their impartiality or independence. The Supreme Court held that Article 18(4) of the Arbitration Act - requiring arbitrators to disclose all "facts likely to give rise to doubts as to his/her impartiality or independence" - (1) is not satisfied by blanket disclosures or advance waivers of potential future conflicts, and (2) requires disclosure of facts both known to an arbitrator or "that can be normally ascertained by an investigation that is reasonably possible${\cdots}$" This new standard presents opportunities and challenges for enforcing arbitration awards in Japan, and suggests measures that both arbitrators and parties can use to protect their awards. Also, the Supreme Court's new standards for evaluating arbitrator conflict disclosures suggest some measures that both arbitrators and parties to arbitration in Japan can take to protect the enforceability of their awards. The key factual question posed by the Supreme Court's ruling was whether an arbitrator's conflicts check was reasonable. Maintaining records regarding a review of potential conflicts or any investigation provides a ready source of proof in case of a future challenge. The Supreme Court has spoken clearly that so-called advance waivers of potential conflicts are not effective under Japanese law. Instead, to the extent that potential conflicts arise during the course of arbitration, they should be specifically disclosed.

• Journal of Korean Academy of Fundamentals of Nursing
• /
• v.7 no.1
• /
• pp.86-96
• /
• 2000

The purpose of the study was to investigate the effects of Warming Therapy used with patients consistantly before and during surgery to on changes in their body temperatures. The data were collected from patients in a university hospital in Taegu between December 1, 1998 and May 31, 1999. The subjects were selected from patients who were hospitalized for total hip replacement surgery. Thirty participants were assigned to two groups : experimental(Warming Therapy) group and control group. Each group consisted of 15 patients. The research design was a repeated measurement design, using a nonequivalent control group. The Warming Therapy, using a forced-air warming blanket, that is a, 'Bair Hugger' was applied to subjects in the experimental group. The subjects in the group were treated with the 'Bair Hugger' to warm up the whole body for 40 minutes before surgery and upper body and face during the operation. The core temperature was measured using a tympanic thermometer. The body temperature of the patients was measured 13 times every 15 minutes during the surgery. After the operation the body temperature of the patients was measured 4 times every 15 minutes, from the time of arrivial in the recovery room to the time of leaving the recovery room. The SPSS Win 9.0 program was used for data analysis. Specific methods tested were done using ${\chi}^2-test$, t-test, repeated measures ANOVA. The findings of the study are as follows. 1. The first hypothesis, 'The level of tympanic temperature for the experimental group which received Warming Therapy will be higher than that of the control group during the operation', was supported (F=32.16, p=.000). 2. The second hypothesis, 'The level of tympanic temperature for the experimental group which received Warming Therapy will be higher than that of the control group after the operation', was supported.(F=33.36, p=.000) 3. During recovery, shivering was observed one patient in the experimental group and seven patients in the control group. In summary, the findings of the study suggest that the 'Warming Therapy' applied before and during the surgery was a very effective treatment for surgical patients in maintaining the core temperature during surgery

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.10
• /
• pp.694-702
• /
• 2013

The purpose of this study is to evaluate a de-watering filtrate treatment and the possibility of securing biological treatment capacity by changing the structure of the secondary clarifier. Accordingly, the column test was conducted to determine the effect of polymer in the de-watering filtrate on sludge sedimentation. Also, the characteristics of de-watering filtrate processing was evaluated through batch test and continuous processing operation. The results showed that sludge settling velocity increased with higher polymer concentration, and that effluent SS concentration was found to decrease. Regarding processing characteristics of de-watering filtrate, the removal efficiency of TSS and TBOD5 increased as the length of secondary clarifier was longer. Also, comparing injections into anoxic tank and secondary clarifier, de-watering filtrate by continuous infusion treatment process showed stability in both conditions. Therefore, by modifying the structure of secondary clarifier, efficient processing of de-watering filtrate is expected to be possible and processing capacity of small sewage treatment plants is considered to be improved.

• Journal of Korea Technology Innovation Society
• /
• v.12 no.1
• /
• pp.1-35
• /
• 2009

This study analyzes the current status of how to manage the national R&D program and the systematic problems of R&D planning, evaluation, and management, and then shows the strategy to support special agency of national R&D management for effective operation. Additionally, this study seeks to search for the macro methods to coordinate and to develop the roles and functions of special agency of national R&D management, and to promote efficiency and productivity of the National R&D investment. First of all, this study generally introduces the national R&D and surveys each special agency of national R&D management by analyzing the status of each agency charged by Ministry. Also, this study defines special agency of national R&D management by investigating each agency's status based on law and finds out the strategy to support special agency of national R&D management for effective operation. Each special agency of national R&D management is based on acts, administrative orders, or blanket contracts and takes whole charge of each National R&D program. The organization forms of special agency of national R&D management can be classified into two forms: One is a form to plan, to evaluate, and to manage the National R&D program and other is a form to research program together with the functions of planning, evaluation, and management. Therefore, this study defines special agency of national R&D management as "an organization, having a legal basis(acts, administrative orders), funded and charged by government for executing R&D planning, evaluation and management of R&D program." This study shows the strategy to operate special agency of national R&D management efficiently by analyzing each agency's current status and comparing each agency with each other. Moreover, every agency has a committee member pool, and the pool is classified well according to the fields of work and technology. Also, the special agency of national R&D management has its own organization to manage performances of program.

• Nuclear Engineering and Technology
• /
• v.56 no.1
• /
• pp.106-113
• /
• 2024

Understanding the tritium release and retention behavior of candidate tritium breeder materials is crucial for breeder blanket design. Recently, a melt spraying process was developed to prepare Li₄SiO₄ pebbles, which were subsequently subjected to the in-pile tritium production and extraction platform in China Mianyang Research Reactor (CMRR) to investigate their in-situ tritium release behavior and irradiation performance. The results demonstrate that HT is the main tritium release form, and adding hydrogen to the purge gas reduces tritium retention while increasing the HT percent in the purge gas. Post-irradiation experiments reveal that the irradiated pebbles darken in color and their grains swell, but the mechanical properties remain largely unchanged. It is concluded that the tritium residence time of Li₄SiO₄ made by melt spraying method at 467 ℃ is approximately 23.34 h. High-density Li₄SiO₄ pebbles exhibit tritium release at relatively low temperatures (<600 ℃) that is mainly controlled by bulk diffusion. The diffusion coefficient at 525 ℃ and 550 ℃ is 1.19 × 10^-11 cm²/s and 5.34 × 10^-11 cm²/s, respectively, with corresponding tritium residence times of 21.3 hours and 4.7 hours.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.1
• /
• pp.85-92
• /
• 2005

The performance of a novel fermentation process, adopting a sludge blanket type configuration for higher hydrolysis/acidogenesis of the municipal primary sludge, was investigated under batch and semi-continuous conditions with various pH and temperature conditions. This acid elutriation slurry reactor provided higher system performance with a short HRT (5 days) and higher acidogenic effluent quality under pH 9 and thermophilic ($55^{\circ}C$) conditions. The hydrolysis of the sludge was revealed to be significantly dependent on seasonal effects for sludge characteristics but with little impact on acidogenesis. Based on the rainy season at the optimum conditions, VFA production and recovery fraction ($VFA_{COD}/COD$) were $0.18\;g\;VFA_{COD}\;g^{-1}\;VSS_{COD}$ and 63%. As byproducts, nitrogen and phosphorus releasing were $0.006\;g\;N\;g^{-1}\;VSS_{COD}$ and $0.003\;g\;P\;g^{-1}\;VSS_{COD}$, respectively. For the mass balance in a full-scale plant($Q=158,880\;m^3\;day^{-1}$) based on the rainy season, the VFA and non-VFA(as COD) production were $3,110\;kg\;VFA_{COD}\;day^{-1}$ and $1,800\;kg\;COD\;day^{-1}$, resulting in an increase of organics of $31\;mg\;COD\;L^{-1}$ and $20\;mg\;VFA_{COD}\;L^{-1}$ and nutrients of $0.7\;mg\;N\;L^{-1}$ and $0.3\;mg\;P\;L^{-1}$ in the influent sewage. The economical benefit from this process application was estimated to be about $67 per $1,000m^3$ of sewage except for energy requirements and also, better benefits can be expected during the dry season. Also, the results revealed that the process has various additional advantages such as pathogen-free stabilized solids production, excellent solids control and economical benefits.

• Journal of environmental and Sanitary engineering
• /
• v.20 no.1 s.55
• /
• pp.64-75
• /
• 2005

The total production of food waste was about 11,398ton/day('03) in Korea. Also, food waste was treated by landfill, incineration, reuse and anaerobic digestion. The method of food waste treatment depended primarily on landfill. However, the method of landfill causing social problems was prevented to treat food waste in the first of January 2005.12) Thus, anaerobic digestion is an important method to treat food waste because of possibility of energy recovery as methane gas. In this study, the possibility of food waste treatment containing high organic material and low pH in the one stage anaerobic reactor to save cost and time and energy recovery using $CH_{4}$ gas by the hybrid anaerobic reactor (HAR) was measured. The HAR was designed by combing the merits of the anaerobic filter (AF) to minimize the microorganism shock when food waste of very low pH was injected and up-flow anaerobic sludge blanket (UASB) to prevent from plugging and channeling phenomena by large suspended solids when semi solids were injected. Granule was packed in the section of HAR. The purpose of the BMP experiment was to measure the amount of methane generated when organic material was resolved under anaerobic conditions, to grasp bio resolution of organic material. Total accumulated methane production per VS amount was $0.471(m^{3}/\cal{kg}\;VS)$. So, the value was about $81.2\%$ of theoretical methane production which was $0.58(m^{3}/\cal{kg}\;VS)$ by elementary analysis and organic matter removal velocity (K) was $0.18(d^{-1})$. From these results, food waste was treated by anaerobic treatment. From this study, $CH_{4}$ generation from food waste (11,398 ton/day) could be estimated. By using an energy conversion factor of Braun's study, $5.97KWh/m^{3}\;CH4,\;60\%\;of\;CH_{4}$ gas generation, the amount of total energy producing food waste is to 6,727MWh/day. It could be confirmed that energy recovery using $CH_{4}$ gas was possible. Above these results, food waste containing organic matters of high concentration could be treated in HRT 30 days under an anaerobic condition, using the hybrid anaerobic reactor and reuse of $CH_{4}$ gas was possible.

• International Journal of Ocean System Engineering
• /
• v.2 no.3
• /
• pp.185-194
• /
• 2012

A Macroscopic combination of two or more distinct materials is commonly referred to as a "Composite Material", having been designed mechanically and chemically superior in function and characteristic than its individual constituent materials. Composite materials are used not only for aerospace and military, but also heavily used in boat/ship building and general composite industries which we are seeing increasingly more. Regardless of the various applications for composite materials, the industry is still limited and requires better fabrication technology and methodology in order to expand and grow. An example of this is that the majority of fabrication facilities nearby still use an antiquated wet lay-up process where fabrication still requires manual hand labor in a 3D environment impeding productivity of composite product design advancement. As an expert in the advanced composites field, I have developed fabrication skills with the use of machinery based on my past composite experience. In autumn 2011, the Korea government confirmed to fund my project. It is the development of a composite sanding machine. I began development of this semi-robotic prototype beginning in 2009. It has possibilities of replacing or augmenting the exhaustive and difficult jobs performed by human hands, such as sanding, grinding, blasting, and polishing in most often, very awkward conditions, and is also will boost productivity, improve surface quality, cut abrasive costs, eliminate vibration injuries, and protect workers from exposure to dust and airborne contamination. Ease of control and operation of the equipment in or outside of the sanding room is a key benefit to end-users. It will prove to be much more economical than normal robotics and minimize errors that commonly occur in factories. The key components and their technologies are a 360 degree rotational shoulder and a wrist that is controlled under PLC controller and joystick manual mode. Development on both of the key modules is complete and are now operational. The Korean government fund boosted my development and I expect to complete full scale development no later than 3rd quarter 2012. Even with the advantages of composite materials, there is still the need to repair or to maintain composite products with a higher level of technology. I have learned many composite repair skills on composite airframe since many composite fabrication skills including repair, requires training for non aerospace applications. The wind energy market is now requiring much larger blades in order to generate more electrical energy for wind farms. One single blade is commonly 50 meters or longer now. When a wind blade becomes damaged from external forces, on-site repair is required on the columns even under strong wind and freezing temperature conditions. In order to correctly obtain polymerization, the repair must be performed on the damaged area within a very limited time. The use of pre-impregnated glass fabric and heating silicone pad and a hot bonder acting precise heating control are surely required.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.11
• /
• pp.2047-2058
• /
• 2000

The effects of operating parameters on performance of upflow anaerobic sludge blanket(UASB). anaerobic filter(AF), and two-stage anaerobic sludge bed filter (ASBF) bioreactors in treating swine wastewater were evaluated by operating the lab-scale bioreactors upto hydraulic retention time(HRT) of 1 day and organic loading rate (OLR) of $5.1kg-COD/m^3{\cdot}d$ for 200 days. Swine wastewaters of which characteristics were affected by types of hog raising and seasons contained high concentrations of COD, SS, and ammonia. Inoculation of the bioreactors with waste sludge from anaerobic treatment facility of local municipal wastewater treatment plant was effective in developing biomass in the bioreactors. Acclimation period of the bioreactors with swine wastewaters required approximately 40 days, but that for AF and two-stage ASBF, which were filled with media, was faster than VASB. The bioreactors showed high and stable COD removal efficiency of 77~91% at influent T-N concentrations of 370~800mg/L but low and unstable COD removal efficiency of 24~94% at influent T-N concentrations of 760~1,310mg/L. It is essential to remove ammonia prior to anaerobic treatment since the concentrations of ammonia in swine wastewaters showed toxic effects to methanogenic bacteria. The bioreactors were effective in treating swine wastewaters with COD removal efficiency of 78.9~81.5% and biogas generation rate of $0.39{\sim}0.59m^3/kg-COD_r$ at OLR of $1.1{\sim}2.2kg-COD/m^3{\cdot}d$: however, an increase of OLR by reducing HRT and increasing influent COD caused decrease of COD removal efficiency. The extent of decrease in COD removal efficiency was higher in UASB than AF and two-stage ASBF. AF and two-stage ASBF anaerobic bioreactors were effective in treating varing characteristics of swine wastewaters since they showed high and stable COD removal efficiency at high OLR due to effective retention of biomass by media and staging.