• 한국가시화정보학회지
• /
• 제8권2호
• /
• pp.51-55
• /
• 2010

Flow characteristics of a free-horizontal-axis-turbine (FHAT) current power generation system have been investigated by the use of a volumetric PTV. Three types of FHAT system (S50, SE50, S65) have been tested under the current speed 1.35 knot, 1.5 knot and 2 knot. The width of the blade installed around the body is 50 mm. Based upon the power generation characteristics of the FHAT, the flow features of the blade have been investigated. Among the three models it has been verified that the S65 is the most appropriate for power generations.

• 한국항공운항학회지
• /
• 제19권4호
• /
• pp.24-29
• /
• 2011

Conceptual study of an open-circuit type low-speed wind tunnel for performance test of wind turbine blade and airfoil is conducted. The tunnel is constituted of a settling chamber, a contraction, closed test section, a diffuser, two corners, a cross leg and a fan and motor. For the performance test, the closed test section width of 1.8 m, height of 1.8 m and length of 5.25 m is selected. The contraction ratio is 9 to 1 and maximum speed in the test section is 67 m/sec. Input power in the tunnel is about 238 kW and its energy ratio is 3.6. The wind tunnel designed in present study will be an effective tool in research and development of wind turbine and airfoil.

• 한국재료학회지
• /
• 제14권4호
• /
• pp.300-306
• /
• 2004

A laser welding has been made between sintered tip of Fe-Co-W and low carbon steel shank for the diamond saw blade. The welding characteristics and formation of defect has been investigated carefully for the weld fusion zone in different welding condition. Full penetration has been observed for the whole range of heat input investigated in the present work. Bead width and under-fill have been increased with the increase of heat input. With increasing of heat input small cavities were decreased while large cavities were increased. The ratio of total cavity area to the entire weld bead area was not changed significantly with change of heat input. Most of cavities were found near the tip, and supposed to be formed from the pore in the tip.

• 한국조경학회지
• /
• 제31권6호
• /
• pp.73-76
• /
• 2004

This study was conducted to investigate the growth responses of Polystichum lepidocaulon as influenced by 4 different shadings(Control, 50%, 70%, 90%). Under 50 or 70% shading, plant height, stipe length, blade length, blade width, and number of spores increased compared with the other shadings, except the number of frond and shoots. The plants grown under control was shown as smaller with more yellowish green leaf color, and under 90% shading the growth was slightly inferior to those under the 50 or 70% shading. Fresh weight and segment area of frond was better in increased shade levels, but they decreased in under 90% shading. Dry weight and segment thickness decreased as shading increased. Chlorophyll contents increased in proportion to lowered light intensity. Thus, 50 or 70% shading of Polystichum lepidocaulon seemed to maintain the highest growth.

• 한국자동차공학회논문집
• /
• 제24권1호
• /
• pp.74-81
• /
• 2016

The aim of this study was to find the initial design value of turbine blade for electrical type turbocompound system generating 10 kW. Turbocompound is one of the waste heat recovery system applying to internal combustion engine to recover exhaust gas energy that was about 30 % of total input energy. To design the turbine blade, 1-D mean line flow model was used. Exhaust gas temperature, pressure, flow rate and turbine rotating speed was fixed as primary boundary conditions. The velocity triangles was defined and used to determine the rotor inlet radius and width, the rotor outlet radius at shroud and radius at hub, the rotor flow angles and the number of blades.

• 한국수산과학회지
• /
• 제54권6호
• /
• pp.982-988
• /
• 2021

Gamma irradiation is one of the simple methods used to induce mutagenesis. Therefore, it is widely used for the development of breeding lineages of plants and algae. In this study, it was developed a new variety of Pyropia yezoensis using gamma irradiation. It was applied a dose of 1 kGy and named the developed mutant Py1k. The blade with width of the mutant was narrower and the blade length was longer than those of the wild type. To further investigate the mutant, it was analyzed the nutrient composition and antioxidant activity. In comparison to those in the wild type, it was found a higher amino acid composition and marginally increased antioxidant activity in Py1k. Based on these results, it was suggests that our protocol can be utilized to develop Pyropia species with improved nutritional quality through gamma irradiation.

• 한국유기농업학회지
• /
• 제11권3호
• /
• pp.75-90
• /
• 2003

우리나라의 재래벼 192품종을 공시하여 다양한 작물학적 특성을 평가하고 양적 형질간의 상근관계를 검토하여 유기농업 및 친환경농업에 적합한 품종을 선발하고 추후 이를 품종육성의 소재로 활용하고자 실험을 수행한 결과는 다음과 같다. 1. 재래벼는 파종에서 출수까지 평균 111.1일이 소요되어 중생종에 속하는 품종이 많았고 초장과 간장은 일반 재배 품종에 비하여 대부분 20∼40cm 정도 컸다. 2. 엽폭과 이삭의 평균 길이는 각각 1.3cm, 22.4cm이었고 주당 이삭수는 평균 10개로 소얼성의 특성을 나타내었으며, 현미의 장폭비는 평균 1.7이었고 장립종도 일부 존재하였으며 천립중은 평균 21.6g이었다. 3. 재래벼의 양적 형질간 상관관졔는 간장과 수장, 엽폭, 출수기간에는 고도로 유의한 정의 상관이 있었으며, 출수기와 천립중 간에는 고도로 유의한 부의 상관이 존재하였다. 4. 간강도는 27.1%가 약한 특성을 나타내었고 엽신과 엽초의 색은 3.6%가 자주줄무늬를 나타냈으며 엽각와 지엽각도는 직립형이 각각 46.9%, 10.9%이었고 엽노화도는 지연형이 24.0%이었다. 5. 재래벼의 74.5%가 까락이 있었고 찰벼는 20.3%, 갈색종피는 4.2%가 존재하였으며, 주두색, 영색, 부선색 및 망색은 백색, 갈색, 적색 및 자색 등 다양한 색이 존재하였다.

• 식물분류학회지
• /
• 제35권2호
• /
• pp.81-98
• /
• 2005

본 연구는 제주도산 벚나무속 식물을 대상으로 잎 형질의 분류학적 중요성을 검토하기 위하여 수행하였다 양적 형질은 엽신의 길이, 엽병의 길이, 엽폭, 엽맥 수, 분지각과 엽저각 등을 조사하였다. 질적 형질은 모용분포와 밀선의 위치 잎의 형태 등을 조사하였다. 총 25개의 OTU에 대해 UPGMA에 의한 표현형적 분석을 실시하였다. 그 결과 subgenus Prununophora에 속하는 매실나무가 subgenus Padus에 속하는 귀릉나무와 섬개벚나무와 같은 유집군을 형성한 점과 subgenus Cerasus에 속하는 벚나무, P. speciosa, 산벚나무, 사옥와 올벚나무, 왕벚나무가 별개의 유집군을 형성한 점 등 일부 분류체계와 다른 양상을 보였다 그러나 subgenus Padus에 속하는 귀릉나무와 섬개벚나무, subgenus Microcerasus에 속하는 이스라지, subgenus Amygdalus에 속하는 복사나무가 각각의 유집군을 형성하는 등 분류체계와 유사한 양상이 강하게 나타났다. 결국, 잎 형질, 그 중에서도 엽신의 길이와 폭의 비, 엽신의 길이와 엽병 길이의 비, 엽맥 수, 잎 기부에서 밀선과의 거리, 주맥과 잎 기부의 좌 우각 등과 모용의 분포 등이 제주도산 벚나무속의 식별형질이 될 수 있을 것으로 판단되었다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2005년도 춘계 학술대회논문집
• /
• pp.25-29
• /
• 2005

Axial fan is used for the supplement of large amount of flows. Axial blowers show relatively high efficiency of the system. The present model of axial fan is for cooling a condenser in an air-conditioning unit that exhibits tendency toward compact size. In order to realize the compact model, the width of an axial blade should be cut down in axial distance. Main interest lies on the performance of the axial blowing system with blades having shorter chord length. One of the important design parameters for axial fan is the shape of the blades of it. Design of blades includes the cross-sectional shape and its dimension, including the chord length. We consider two types of blades; one is NACA airfoil with normal chord length and the other is with shortening chord length by $10\%$ of normal airfoil. Axial blower with the modified blades is essential for the compact model of an air-conditioner. The other design parameters are same in the two cases. Using a wind tunnel follows ASHRAE standards carries out evaluation of performance of the system. Detail of flows around the blades is prepared by velocity measurements using PIV. According to performance estimation, the axial blower with short chord blade show quite close to the performance results, including flow rate and pressure rise, of the standard one. The reason of the two similar results is that the flowpatterns depend on Reynolds number based on the chord length of a blade. In this investigation, the critical chord length is found, in which the flows near the airfoil are so unstable and the performance of the system is decreased. A series of figures is for the detail information on the flow.

• 한국소음진동공학회논문집
• /
• 제20권12호
• /
• pp.1153-1160
• /
• 2010

A circular plate is the main part of a circular saw blade, which is widely used in industrial cutting tools. In experiments using a circular saw containing slots, we observed that a number of natural frequencies are simultaneously emerged in specific frequency regions. The interesting phenomenon is called the frequency convergence. Effects of design parameters such as the number, the length and the width of slots, on the frequency-convergence phenomenon are analyzed by FEM simulations using ALGOR. The frequency-convergence phenomenon will be intensified when the number, length and width of slots increase.