• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.5 no.1
• /
• pp.37-46
• /
• 1999

Water vapor permeability of films is commonly calculated from the water vapor transmission rate of the film measured using a permeability cup method which is essentially a gravimetric method. This method was originally developed for petroleum based plastic films with low water vapor permeability. In the case of hydrophilic bio-polymer films, the resistance caused by a stagnant air layer, which is developed between the underside of the film mounted on the cup and the surface of the desiccant saturated salt solution or distilled water, can be significant and, if neglected, ran lead to underestimation of water vapor transmission rates. Therefore, it is necessary to correct water vapor transmission rate data to accurately estimate the water vapor permeability of bio-polymer films.

• Textile Coloration and Finishing
• /
• v.21 no.4
• /
• pp.33-38
• /
• 2009

Poly(vinyl acetate) films containing benzophenone were photocrosslinked by continuous UV irradiation.UV irradiation of PVAc film containing 5% benzophenone induced bulk crosslinking of the polymer indicated by 84.1% of gel fraction after ethyl acetate extraction. The crosslinking was attributed to the recombination of tertiary polymer radicals generated upon UV irradiation, which was enhanced by the hydrogen abstraction of benzophenone. Also the UV irradiation resulted in scission of ester linkage and photooxidation of PVAc surface, which was verified by ATR and zeta potential analysis, implying that the PVAc surface became more polar and hydrophilic. The zeta potential proportionally increased from +4.5mV to -26.8 mV with increasing UV irradiation. Also the surface energy of the PVAc film increased with higher UV irradiation upto 56.5 $mJ/m^2$ by the enhanced Lewis acid/base component with larger contribution of Lewis acid parameter. Accordingly the crosslinked PVAc showed higher thermal stability with increasing UV energy.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.902-903
• /
• 2009

Polymer Dispersed Liquid Crystal (PDLC) films were prepared using the phase separation method with liquid crystal and a newly developed prepolymer. This study investigated the electro-optic characteristics of the PDLC film at various temperatures. It was found that as temperatures increased, the voltage varied, and that the ordinary refractive index of the liquid crystal and the polymer refractive index in the composite had similar dependence at various temperatures.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.3
• /
• pp.144-151
• /
• 2003

IPMC(Ionic Polymer-Metal Composite) is promising candidate material for bio-related actuators mainly due to its biocompatibility and wet and soft properties. The widely used commercialized Nafion film has a few kinds of fixed thicknesses but more various film thicknesses are required for extensive applications. Especially for the enhanced force as an actuator, the thick film is essential. Various Nafion films with thickness of 0.4-1.2mm have been prepared by casting of liquid Nafion. Also, IPMC actuators using casted Nafion films have been fabricated and the basic mechanical properties such as stiffness, displacement and force were measured and analyzed. These results can be used for the optimized design of actuators for different applications.

• Korean Journal of Materials Research
• /
• v.14 no.6
• /
• pp.443-450
• /
• 2004

Parylene polymer thin film shows excellent homogeneous coverage chracteristics when it was deposited onto very complex three dimensional solid matters, such as deep hole and micro crack. The parylene deposition process can be conducted at room temperature although most of chemical vapor deposition processes request relatively high processing temperature. Therefore, the parylene coating process does not induce any thermal problems. Parylene thin film is transparent and has extremly high chemical stability. For example, it shows high chemical stability with high reactive chemical solutions such as strong acid, strong alkali and acetone. The bio-stability of this material gives good chances to use for a packaging of biomedical devices and electronic devices such as display. In this review article, principle of deposition process, properties and application fields of parylene polymer thin film are introduced.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.8
• /
• pp.2291-2296
• /
• 2013

An efficient carbon monoxide (CO) sensor was developed based on poly(3,4-ethylenedioxy)thiophenepoly(styrenesulfonate) (PEDOT:PSS) modified with a new pyrimidine-fused heterocyclic compound, bis(2-hydroxyphenyl)dihydropyrido[2,3-d:6,5-d]dipyrimidine-tetraone (B2HDDT). B2HDDT remains stable in the polymer matrix through interactions with functional groups of the polymer. It created prominent sites that captured CO gas, and the experimental parameters, including the amount of doped B2HDDT in the PEDOT:PSS film, were optimized. The sensor probe was also examined to verify its reliability for detecting CO in the presence of atmospheric gases in a discriminating manner. NMR, AFM, and FT-IR spectra were obtained to evaluate the structure and morphology of the B2HDDT-doped PEDOT:PSS (PEDOT:PSS/B2HDDT) film. The content of 35 vol % B2HDDT (7.0 mM) in PEDOT:PSS provided the largest response factor (${\Delta}R/R_o$) for the CO gas. The sensor response was reproducible, with a relative standard deviation < 5% (n = 5). The detection limit was determined to be $0.44{\pm}0.05$ vol %.

• Korean Journal of Optics and Photonics
• /
• v.19 no.3
• /
• pp.193-198
• /
• 2008

A novel refractive index sensor, which consists of polymer channel waveguide overlaid with $TiO_2$ thin film, is demonstrated. To evaluate the fabricated sensor, we measured the polarimetric interference induced by concentration change of injected glycerol solution. Our experimental results show that thicker $TiO_2$ film improves the sensitivity of the polarimetric interferometer. For the fabricated waveguide with a 20 nm thick $TiO_2$ film, the measured index change to lead phase variation of $2{\pi}$ is $1.8{\times}10^{-3}$.

• Korean Journal of Organic Agriculture
• /
• v.19 no.spc
• /
• pp.119-122
• /
• 2011

Among the developed bio-degradable polymer films as compared with transparent film(White), black polymer film was significantly more effective for controlling weeds in red pepper. Also, we found that white and black polymer mulching had 81.8% and 97.9% of managing weed controlling effects in rice, respectively. Compared to non-mulched rice paddy with water supply, the non-mulched rice paddy without any water supply has stopped its growth at 41 days after transplanting, while polymer-mulched rice paddy without water supply had about 60% of normally growing rice plants. This shows the polymer treatment has a remarkable effect on water and power saving, solution of herbicidal resistance, avoidance of herbicidal influence to eco-system etc. When the naturally decomposing polymer was used, a temperature was elevated as high as $4.7^{\circ}C$ on maximum and $2.6^{\circ}C$ on average. Also the naturally decomposing polymer accelerated rooting by 7 days and lowered a stress level from transplanting. The weed control effect mulched by polymer was remarkable as 98.7%. The polymer now, after 294 days treated on the rice paddy, has been completely decomposed.

• Macromolecular Research
• /
• v.17 no.11
• /
• pp.850-855
• /
• 2009

Keratin is an important protein used in wound healing and tissue recovery. In this study, keratin was modified chemically with iodoacetic acid (IAA) to enhance its solubility in organic solvent. Poly(hydroxybutylate-co-hydroxyvalerate) (PHBV) and modified keratin were dissolved in hexafluoroisopropanol (HFIP) and electrospun to produce nanofibrous mats. The resulting mats were surface-characterized by ATR-FTIR, field-emission scanning electron microscopy (FE-SEM) and electron spectroscopy for chemical analysis (ESCA). The pure m-keratin mat was cross-linked with glutaraldehyde vapor to make it insoluble in water. The biodegradation test in vitro showed that the mats could be biodegraded by PHB depolymerase and trypsin aqueous solution. The results of the cell adhesion experiment showed that the NIH 3T3 cells adhered more to the PHBV/m-keratin nanofibrous mats than the PHBV film. The BrdU assay showed that the keratin and PHBV/m-keratin nanofibrous mats could accelerate the proliferation of fibroblast cells compared to the PHBV nanofibrous mats.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.3
• /
• pp.927-933
• /
• 2011

Conducting polyaniline-poly($\varepsilon$-caprolactone) polymer composites were synthesized via in situ deposition techniques. By dissolving different weight percentages of poly($\varepsilon$-caprolactone) (PCL) (10%, 20%, 30%, 40%, and 50%), the oxidative polymerization of aniline was achieved using ammonium persulfate as an oxidant. FTIR, UV-vis spectra, and X-ray diffraction studies support a strong interaction between polyaniline (PANI) and PCL. Structural morphology of the PANI-PCL polymer composites was studied using scanned electron microscopy (SEM) and transmittance electron microscopy (TEM), and thermal stability was analyzed by thermogravimetric analysis (TGA) technique. The temperature-dependent DC conductivity of PANI-PCL polymer composite films was studied in the range of 305-475 K, which revealed a semiconducting behavior in the transport properties of the polymer films. Conductivity increased with the increase of PCL in below critical level, however conductivity of the polymer film was decreased with increase of PCL concentration higher than the critical value.