• 약학회지
• /
• 제42권3호
• /
• pp.290-295
• /
• 1998

To optimize the formulation of acetaminophen liquid suppository, the effect of additives on the physicochemical properties of liquid suppository base was investigated. The physi cochemical properties of P 407/P 188 (15/15%) (abbreviated in 15/15) and P 407/P l88 (15/20%) (abbreviated in 15/20) were measured after the addition of following additives; 2.5% acetaminophen as an active ingredient, vehicle components (5% ethanol, 5% propylene glycol, 5% glycerin), preservatives (0.1% sodium benzoate, 0,1% methylparahydroxybenzoate, 0.1% propylparahydroxybenzoate) and 1% of sodium chloride as an ionic strength controlling agent. Poloxamer gel was prepared with three different buffer solutions (pH 1.2, 4.0 and 6.8) and the physicochemical properties, gelation temperature, gel strength and bioadhesive force, were determined. In the results, the effect of additives on the physicochemical properties was dependent on their bonding capacities including hydrogen bonding and cross-linking bonding. Because the hydrogen-bonding capacities of acetaminophen, ethanol and propylene glycol were smaller than that of poloxamer, the binding force of poloxamer gel became weak by their putting in between poloxamer gel. Therefore, the gelation temperature (15/15, $35.7^{\circ}C$ vs 37.0, 39.4 $38.2^{\circ}C$; 15/20, $29.2^{\circ}C$ vs 31.2, 32.0, $30.3^{\circ}C$) increased, and gel strength (15/15, 4.03 see vs 2.72, 2.08, 3.12sec; 15/20, 300g vs 50, 50, 200g) and bioadhesive force (15/15, $6.8{\times}10^2\;dyne/cm^2$ vs 3.2, 6.0, $6.0{\times}10^2\;dyne/cm^2$; 15/20, $97.3{\times}10^2\;dyne/cm^2$ vs 11.1, 89.5, $92.0{\times}10^2\;dyne/cm^2$) decreased. Furthermore, the binding force of poloxamer gel became strong due to the hydrogen-bonding capacities of glycerin and the cross-liking bonding of sodium salt. Then, the gelation temperature (15/15, 35.0, $32.1^{\circ}C$; 15/20, 26.0, $21.0^{\circ}C$) decreased, and gel strength (15/15, 6.51 see, 300g; 15/20, 500, 650g) and bioadhesive force (15/15, 7.2, $81.6{\times}10^2\;dyne/cm^2$; 15/20, 112.3, $309.2{\times}10^2\;dyne/cm^2$) increased. The effect of pH on the physicochemical properties of poloxamer gel was dependent on the ingredients with which the buffer solutions were prepared. Poloxamer gels prepared with pH 1.2 and 4.0 buffer solutions had the increasing gelation temperature (15/15, 37.5, $38.1^{\circ}C$; 15/20, 33.1, $34.0^{\circ}C$) and the decreasing gel strength (15/15, 2.98, 3.81sec; 15/20, 200, 200g) and bioadhesive force (15/15, $7.0{\times}10^2dyne/cm^2$; 15/20, $74.0{\sim}88.1{\times}10^2dyne/cm^2$) owing to HCl. Poloxamer gel prepared with pH 6.8 buffer solutions had the decreasing gelation temperature (15/15, $27.2^{\circ}C$; 15/20, $22.3^{\circ}C$) and the increasing gel strength (15/15, 400g; 15/20, 550g) and bioadhesive force (15/15, $207.0{\times}10^2dyne/cm^2$; 15/20, $215.0{\times}10^2dyne/cm^2$) due to the cross-linking bonding of $NaH_2PO_4\;and\;K_2HPO_4$.

• 대한소아치과학회지
• /
• 제49권3호
• /
• pp.264-273
• /
• 2022

치과에서 사용하는 재료들의 물성의 발달로 인하여 브라켓과 치아 사이의 결합 능력도 크게 향상되었다. 그러나 소아치과 영역에서와 같이 환자의 협조를 기대하기 어렵거나, 수분 격리가 제대로 이루어지지 않을 경우 기대하는 효과에 미치지 못하는 결합강도를 보여 줄 수 있다. 본 연구의 목적은 세 가지의 접착 술식을 비교하여 브라켓의 전단 접착 강도를 평가하고, 임상적으로 유의한 차이가 존재하는지 비교하는 것이다. 우식증이나 수복물이 없는 상, 하악 소구치 60개 치아를 대상으로 하였다. Group I은 대조군으로서 기존의 3 step 접착 방식에 따라 브라켓을 부착하였고, Group II는 self-etching primer system을 이용하여 부착하였다. Group III는 self-priming adhesive를 이용하여 브라켓을 부착하였다. 각 group의 전단 결합 강도를 측정하고 접착제 잔류지수(ARI)를 기록하였다. 각 group I, II, III의 평균 전단 결합 강도는 14.69 MPa, 11.21 MPa 그리고 12.21 MPa로 측정되었다. Group I과 II, group I과 III에서만 유의한 차이가 존재하였으며(p < 0.05), ARI 값은 모든 group에서 유의한 차이가 존재하지 않았다.

• Asian-Australasian Journal of Animal Sciences
• /
• 제20권8호
• /
• pp.1285-1291
• /
• 2007

This research investigated variation in the improvement of the texture of chicken and pork sausages induced by microbial transglutaminase (MTG). The extractability of myofibrillar proteins from these sausages as well as the ${\varepsilon}-({\gamma}-glutamyl)$lysine (G-L)　content were also investigated. MTG treatment of sausages significantly increased the breaking strength values in both meat types, especially for samples incubated at $40^{\circ}C$. However, values of the breaking strength in both meat types were increased differently. The variation in protein extractability of samples incubated at $40^{\circ}C$ for both meat types could lead to some consideration of the mechanisms and the high accessions of myosin heavy chain (MHC) to MTG. SDS-PAGE analysis showed significant changes in the density of the bands after adding MTG, especially for the pork samples in which the bands disappeared totally. The G-L content in the presence of MTG was double that in control samples of both meat types. This study suggests that the binding ability of myofibrillar proteins with MTG is strong. This leads us to suggest that MTG functions positively with different improvements in the texture of chicken and pork products that are treated mechanically, such as sausages. Variability in gel improvement level between chicken and pork sausages was observed; this resulted from the variation in meat proteins in response to MTG, as well as to the original glutamyl and lysine content.

• Composites Research
• /
• 제33권5호
• /
• pp.282-287
• /
• 2020

본 연구에서는 저 융점 폴리에틸렌 테레프탈레이트(PET) 섬유(Low melting PET fiber: LMF)가 복합화된 PET 시트의 고밀도화 공정을 통해 고강도 PET 시트를 제조하였다. 복합화된 LMF는 열처리 과정에서 용융되어 개개의 PET 섬유를 연결해 섬유간의 계면결합력을 향상시켰다. 또한 PET시트의 고밀도화는 거대기공밀도를 감소시키고 중첩된 PET 네트워크간의 결합력을 향상시켜 결과적으로 압축 전 LMF-PET 시트와 비교하여 연신율은 유지하면서 약 410% 향상된 인장강도를 보여주었다. 또한 강화된 결합력은 PET 섬유 네트워크의 수축을 방지하여 우수한 치수안정성을 나타내었다.

• 복합신소재구조학회 논문집
• /
• 제6권2호
• /
• pp.52-62
• /
• 2015

This study aims at developing a new seismic resistant method by using precast concrete wall panels for existing low-rise, reinforced concrete beam-column buildings such as school buildings. Three quasi-static hysteresis loading tests were performed on one unreinforced beam-column specimen and two reinforced specimens with U-type precast wall panels. Top shear connection of the PC panel was required to show the composite strength of RC column and PC wall panel. However, the strength of the connection did not influence directly on the ultimate loading capacities of the specimens in the positive loading because the loaded RC column push the side of PC wall panel and it moved horizontally before the shear connector receive the concentrated shear force in the positive loading process. Under the positive loading sequence(push loading), the reinforced concrete column and PC panel showed flexural strength which is larger than 97% of the composite section because of the rigid binding at the top of precast panel. Similar load-deformation relationship and ultimated horizontal load capacities were shown in the test of PR1-LA and PR1-LP specimens because they have same section dimension and detail at the flexural critical section. An average of 4.7 times increase in the positive maximum loading(average 967kN) and 2.7 times increase in the negative maximum loading(average 592.5kN) had resulted from the test of seismic resistant specimens with anchored and welded steel plate connections than that of unreinforced beam-column specimen. The maximum drift ratios were also shown between 1.0% and 1.4%.

• 대한환경공학회지
• /
• 제36권12호
• /
• pp.843-850
• /
• 2014

본 연구는 국내 하수처리장에서 발생하는 감량화/안정화된 소각재를 무기바인더로 재이용하기 위하여 수행하였다. 실험은 무소성 공정으로 진행하였으며, Sewage Sludge Ash를 시멘트, Geobond 등의 바인더와 모래를 혼합하여 페이스트 시편과 몰탈 시편으로 성형하였다. 성형 후 양생과정을 거친 시편을 압축강도를 측정한 결과 KS 기준치 22.54 Mpa ($229.7kg/cm^2$)을 상회하고, 하수슬러지 소각재(SSA) 첨가율은 약 10~40%까지 가능한 것으로 나타나 개발하고자 한 하수슬러지 소각재를 무기바인더인 시멘트, Geobond의 대체 물질로 재활용이 가능함을 입증하였다.

• 한국염색가공학회지
• /
• 제25권3호
• /
• pp.172-180
• /
• 2013

Aramid fibers are being used increasingly in a wide range of application due to low density, high specific strength, high modulus, and high thermal resistance. But owing to its special physical and chemical structures, it is sensitive to absorb the ultraviolet light which will degrade the fiber's useful mechanical properties and structure. In this paper, the sol-gel technique was used to improve the photo-stability of p-aramid fibers. $TiO_2$, modified $SiO_2$/$TiO_2$ sol were used as coating solutions. The influence of the such coatings on the photo-stability of p-aramid fiber was investigated by an accelerated photo-ageing method using xenon lamp. The photo-stability of p-aramid fiber showed obvious improvement after the modified silica binding coating. But the amorphous $TiO_2$ sol coatings showed a negative effect. After 144h light exposure, the modified silane binder-coated fibers showed less degradation in mechanical properties with the retained tensile strength greater than about 70% of the original value.

• 한국건축시공학회지
• /
• 제19권4호
• /
• pp.323-330
• /
• 2019

시멘트 산업은 온실가스 감축을 위한 주요 산업분야로 고려되고 있으며, 콘크리트에 시멘트를 대체할 수 있는 재료의 사용량을 증가시키는 것은 이산화탄소 감축을 위해 효과적인 방법으로 알려져 있다. 따라서 시멘트의 일부를 대체하여 사용할 수 있는 산업부산물을 다량으로 활용하기 위한 연구가 진행되고 있다. 그러나 산업부산물의 혼합량을 증가시키지 못하는 큰 이유로 초기강도 저하와 응결지연에 대한 문제점이 있다. 따라서 이 연구에서는 보통 시멘트를 사용한 경우와 고분말도 시멘트를 사용한 경우에 대해 플라이애시의 사용량에 차이를 두고 물리적 특성을 검토하여, 시멘트의 사용량을 줄이고 산업부산물을 다량으로 사용하기 위한 방안으로서, 고분말도 시멘트를 활용한 결과에 대한 기초 자료를 제시하였다.

• Geomechanics and Engineering
• /
• 제29권3호
• /
• pp.311-320
• /
• 2022

TBM concrete segment requires a higher level of material properties compared to general concrete structures due to difficulties in maintenance and uncertainty in ground conditions. In this regard, recently, as one of the methods to achieve enhancement effect on concrete strength, many researchers have been focusing on adding CNTs to concrete mixture. However, even CNTs do not compensate the weakness that concrete exhibits brittle behavior after cracking. Separately, over the past few decades, a number of studies have been conducted on fiber reinforced concrete which exhibits ductile behavior due to fibers bridging cracks. However, only limited studies have been conducted to employ the advantages of the both materials together. In this study, an experimental program has been conducted to investigate the effect of CNTs on the workability and the compressive behavior of PVA-ECC which exhibits ductile tensile behavior with well-distributed cracks even without a conventional rebar. In addition to the compression test, SEM analysis has been also conducted for detailed investigation in the microstructure. The variable was the CNTs mix ratio, which were set to 0.00, 0.25, and 0.50 wt.% to the binding materials. It was observed though the test results that as the CNTs mix ratio increased, the workability considerably decreased with the reduced slump and slump flow. From the compression test results, it was also investigated that the compressive behavior was improved since the compressive strength, the strain corresponding to the compressive strength, and the modulus of elasticity increased with an increase of CNTs mix ratio. The contents of this paper will be useful for relevant research areas such as fiber reinforced concrete with CNTs which might be applied for high performance TMB concrete segments.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.71-71
• /
• 2012

Chemically modified graphene has been great interest for the application of printed electronics using solution prossesable technique. Here, we demonstrate a large area graphene exfoliation method with fewer defects on the basal plane by application of shear stress in solution to obtain high quality reduced graphene oxide (RGO). Moreover, we introduce a novel route to preparing highly concentrated and conductive RGO in various solvents by monovalent cation-${\pi}$ interaction. Noncovalent binding forces can be induced between a monopole (cation) and a quadrupole (aromatic ${\pi}$ system). The stability of this RGO dispersion was more sensitive to the strength of the cation-${\pi}$ interactions than to the cation-oxygen functional group interactions. The RGO film prepared without a post-annealing process displayed superior electrical conductivity of 97,500 S/m. Our strategy can facilitate the development of large scalable production methods for preparing printed electronics made from high-quality RGO nanosheets.